Optoma Hd200x Projector User Manual
Have a look at the manual Optoma Hd200x Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1077 Optoma manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
41 English ppendices On Screen Messages Fan failed: The projector will switch off automatically. Over temperature: The projector will switch off automatically. Replacing the lamp: Lamp is approaching the end of it’s rated life. Replcement suggested. Remote Control Problems If the remote control does not work Check the operating angle of the remote control is within ±15° both horizontally and vertically of one of the IR receivers on the projector. Make sure there are not any obstructions between the remote control and the projector. Move to within 8 m of the projector. Make sure the batteries are inserted correctly. Replace batteries if they are exhausted.
42 ppendices Replacing the lamp The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp. Warning: Lamp compartment may be hot! Allow it to cool down before changing the lamp! Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped. Warning: If ceiling mounted, please use caution when opening the lamp access panel. It is recommended to wear safety glasses if changing the bulb when ceiling mounted. “Caution must be used to prevent any loose parts from falling out of projector.”
43 English ppendices Lamp Replacement Procedure: 1. Switch off the power to the projector by pressing the “” button. 2. Allow the projector to cool down for at least 30 minutes. 3. Disconnect the power cord. 4. Unscrew the two screws on the cover. 1 5. Lift up and remove the cover. 2 6. Unscrew the two screws on the lamp module. 3 7. Lift up the lamp handle and remove the lamp module slowly and carefully. 4 To replace the lamp module, reverse the previous steps. 8. Turn on the projector and use “Lamp Reset” after the lamp module is\ replaced. Lamp Reset: (i) Press “Menu” (ii) Select “SYSTEM” (iii) Select “Lamp Settings” (iv) Select “Lamp Reset” (v) Select “Yes”. 1 2 3 4 The screws on the lamp cover and the lamp cannot be removed. The projector cannot be turned on if the lamp cover has not been placed back on the projector. Do not touch the glass area of the lamp. Hand oil can cause the lamp to shatter. Use a dry cloth to clean the lamp module if it was accidentally touched. NoteNote
44 ppendices Compatibility Modes Computer Compatibility For widescreen resolution (WXGA), the compatibility support is dependent on Notebook/PC models. ModeResolutionV.Frequency (Hz) AAnalogDigital SVGA 800 x 60056 800 x 60060 800 x 60072 800 x 60075 800 x 60085 XGA 1024 x 76860 1024 x 76870 1024 x 76875 1024 x 76885 WXGA1280 x 76860 1280 x 80060 HD 1280 x 72060 1280 x 102460 1280 x 102475 1920 x 108024 1920 x 108060 SXGA+1400 x 105060 UXGA1600 x 120060 Power Book G4 SVGA800 x 60060 800 x 60075 800 x 60085 XGA1024 x 76860 1024 x 76870 1024 x 76875 1024 x 76885 WXGA1280 x 76860 HD1280 x 72060 1280 x 102460 1280 x 102475 SXGA+1400 x 105060 UXGA1600 x 120060 iMAC XGA1024 x 76860 NoteNote
45 English ppendices Video Compatibility NTSCM (3.58MHz), 4.43 MHz PALB, D, G, H, I, M, N SECAMB, D, G, K, K1, L SDTV/HDTV480i/p, 576i/p, 720p@50Hz/60Hz, 1080i/p@50Hz/60Hz
46 ppendices Please note that damage resulting from incorrect installation will invalidate the warranty. Ceiling Mount Installation 1. To prevent damage to your projector, please use the Optoma ceiling mount. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector meet the following specifications: Screw type: M3*3 Maximum screw length: 10mm Minimum screw length: 7.5mm Warning: 1. If you buy a ceiling mount from another company, please be sure to use the correct screw size. Screw size will vary depending on the thickness of the mounting plate.2. Be sure to keep at least 10 cm gap between the ceiling and the bottom of the projector.3. Avoid installing the projector near a heat source. NoteNote NoteNote Lens 82.30 93.60 110.00137.2076.40 55.00 131.40323.60 233.30 59.01Unit: mm
47 English ppendices Optoma Global Offi ces For service or support please contact your local offi ce. USA 715 Sycamore Drive Tel : 408-383-3700 Milpitas, CA 95035, USA Fax: 408-383-3702 www.optomausa.com Service : [email protected] Canada 5630 Kennedy Road, Mississauga, Tel : 905-361-2582 ON, L4Z 2A9, Canada Fax: 905-361-2581 www.optoma.ca Service : [email protected] Europe 42 Caxton Way, The Watford Business Park Watford, Hertfordshire, WD18 8QZ, UK Tel : +44 (0) 1923 691 800 www.optoma.eu Fax: +44 (0) 1923 691 888 Service Tel : +44 (0)1923 691865 Service : [email protected] France Bâtiment E Tel : +33 1 41 46 12 20 81-83 avenue Edouard Vaillant Fax: +33 1 41 46 94 35 92100 Boulogne Billancourt, France Service : [email protected] Spain C/ José Hierro,36 Of. 1C Tel : +34 91 499 06 06 28529 Rivas VaciaMadrid, Fax: +34 91 670 08 32 Spain Deutschland Werftstrasse 25 Tel : +49 (0) 211 506 6670 D40549 Düsseldorf, Fax: +49 (0) 211 506 66799 Germany Service : [email protected] Scandinavia Grev Wedels Plass 2 Tel : +47 32 26 89 90 3015 Drammen Fax: +47 32 83 78 98 Norway Service : [email protected] Latin America 715 Sycamore Drive Tel : 408-383-3700 Milpitas, CA 95035, USA Fax: 408-383-3702 www.optoma.com.br www.optoma.com.mx
48 ppendices Korea WOOMI TECH.CO.,LTD. 4F,Minu Bldg.33-14, Kangnam-Ku, Tel : +82+2+34430004 seoul,135-815, KOREA Fax: +82+2+34430005 Japan 東京都足立区綾瀬3-25-18 株式会社オーエスエム E-mail : [email protected] サポートセンター:0120-46-5040 www.os-worldwide.com Taiwan 5F., No. 108, Minchiuan Rd. Tel : +886-2-2218-2360 Shindian City, Fax: +886-2-2218-2313 Taipei Taiwan 231, R.O.C. Service : [email protected] www.optoma.com.tw asia.optoma.com Hong Kong Unit A, 27/F Dragon Centre, 79 Wing Hong Street, Tel : +852-2396-8968 Cheung Sha Wan, Fax: +852-2370-1222 Kowloon, Hong Kong www.optoma.com.hk China 5F, No. 1205, Kaixuan Rd., Tel : +86-21-62947376 Changning District Fax: +86-21-62947375 Shanghai, 200052, China www.optoma.com.cn
49 English ppendices Regulation & Safety notices This appendix lists the general notices of your projector. FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the device and receiver. • Connect the device into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/television technician for help. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations. Caution Changes or modifi cations not expressly approved by the manufacturer could void the user’s authority, which is granted by the Federal Communications Commission, to operate this projector.
50 ppendices Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference and 2. This device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian users This Class B digital apparatus complies with Canadian ICES-003. Remarque à l’intention des utilisateurs canadiens Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. Declaration of Conformity for EU countries • EMC Directive 2004/108/EC (including amendments) • Low Voltage Directive 2006/95/EC • R & TTE Directive 1999/5/EC (if product has RF function) Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle it.