Optoma H27 Projector User Manual

E
nglish
11
Installation
Power/Standby
Powering On the Projector
1.Remove the lens cap.
2.Ensure that the power cord and signal cable are securely
connected.  The Power LED will flash green.
3.Turn on the lamp by pressing “Power/Standby” button on
the control panel.n  And the Power LED will turn green.
The first time you use the projector, you can select your
prefered language from quick menu after the startup
screen display.
4.Turn on your source (computer, notebook, video player,
etc.).  The projector...

E
nglish
12
Installation
Warning Indicator
™When the “LAMP” indicator lights solid red, the projector will
automatically shut itself down.  Please contact your local reseller
or service center.
™When the “TEMP” indicator lights solid red for about 20
seconds, it indicates the projector has been overheated.  You
will see a message “Projector Overheated. Lamp will auto-
matically turn off soon.” on the on-screen display.  The
projector will automatically shut itself down.
Under normal conditions, the...

E
nglish
13
Elevator Foot
Installation
The projector is equipped with an elevator foot to adjust the
image height.
To raise or lower the image :
1. Turn the projector over and locate the elevator foot. Press
the elevator button 
n  to extend the foot so it may be
adjusted.
2. While holding down the elevator button, adjust the foot to
the desired height, 
o then release the button to lock the
elevator foot into position.
3. Use 
p to fine-tune tilt-adjustment
4. Lower the projector so it rests on its...

E
nglish
14
Zoom Lever
Adjusting the Projector’s Zoom/Focus
You may adjust the zoom  to zoom the lens in or out.  Turn the
zoom lever
 to zoom in or  zoom out.  To focus on the image, turn
the focus ring until you see a clear image. The projector will fo-
cus at distances from 4.9 to 40.7 feet (1.5 to 12.5 meters).
Installation
Focus Ring   

E
nglish
15
User Controls
Control Panel & Remote Control
There are two ways to control the projector: through the remote
control or through the control panel on the projector.
Using the Remote Control
Power
4“Power” turns on the projector’s lamp. Refer to the “Powering
On/Off the Projector” section on page 11~ 12 for more details.
Hide
4“Hide” immediately turns the screen black. Press “Hide” again
to restore the displayed image.
Freeze
4“Freeze” pauses the screen image, press “Freeze” again to un-...

E
nglish
16
User Controls
Contrast
4Control the degree of difference between the lightest and
darkest parts of the picture.
Keystone +/-
4Correct image distortion caused by tilting the projector.
4 : 3
4Scale the image at a 4:3 aspect ratio.
16 : 9
4Scale the image at a 16:9 aspect ratio.
1:1
4The input source will be displayed without scaling.
Letterbox
4Enable the viewing of the letterboxed non-anamorphically
enhanced movie at full screen width. Part of the original image
will be lost if the image...

E
nglish
17
Using the Control Panel
Power/Standby  
4Refer to the “Power  On/Off the Projector” section on pages
11-12.
Source  
4Press “Source” to choose DVI, RGB, S-Video, SCART RGB,
Composite, Component and HDTV sources.
Menu 
4Display or exits the onscreen display menus.
Keystone + /- 
4Adjusts image distortion caused by tilting the projector (±16
degrees).
Four Directional Select Keys
4Press “Menu,” then use         to select items or
make adjustments to your selection.
Enter 
4Confirm your...

E
nglish
18
User Controls
How to Operate
4The projector has multilingual on-screen display menus that allow
you to make image adjustments and change a variety of settings.
The projector automatically detects the source.
4Press “Menu” on the Remote Control or Control Panel.
4When the menu is displayed, use         to navigate the main
menu. To Select a specific icon, press “Enter” to access related.
ŠTo exit the main menu, press  or “Menu” .
4When  a sub menu is displayed, use      to select the desired...

E
nglish
19
User Controls
Menu Tree   

E
nglish
20
User Controls
Image-I
(Computer Mode)
Display Mode
There are many factory presets optimized for various types of
images.
4Normal : For nomal status.
4Movie : For home theater.
4Game : For game.
4TV : For TV standard color.
4User 1 / User 2: Memorize user’s settings.
Brightness
Adjust the brightness of the image.
4Press  to darken image.
4Press  to lighten image.
Contrast
Contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast...