Optoma Ex665utis Projector User Manual

							51English
User Controls
 Reset Dust Filter
Choose “Yes” to show or “No” to hide the warning message when 
the changing filter message is displayed.
 Reset
Choose “Yes” to return the display parameters on all menus to the 
factory default settings. 
						

							52English
User Controls
OPTIONS | 
Advanced
 Direct Power On
Choose “On” to activate Direct Power mode. The projector will 
automatically power on when AC power is supplied, without 
pressing the “” key on the projector control panel or on the 
remote control.
 Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start, 
when there is no signal being sent to the projector. The projector 
will automatically power off when the countdown has finished (in 
minutes).
 Sleep Timer (min)
Sets the countdown timer interval. The countdown timer will start, 
with or without a signal being sent to the projector. The projector 
will automatically power off when the countdown has finished (in 
minutes).
 Power Mode (Standby)
 Eco.: Choose “Eco.” to save power dissipation further < 1W.
 Active: Choose “Active” to return to normal standby and the 
VGA out port will be enabled. 
	When Power mode (Standby) is set to Eco (
						

							53English
User Controls
OPTIONS |  
Lamp Settings
 Lamp Hours
Display the projection time.
 Lamp Reminder
Choose this function to show or to hide the warning message 
when the changing lamp message is displayed.  
The message will appear 30 hours before suggested replacement 
of lamp.
 Brightness Mode
 STD: Choose “STD” to dim the projector lamp which will lower 
power consumption and extend the lamp life. 
 BRIGHT: Choose “BRIGHT” to increase the brightness. 
 Image AI:  Choose “Image AI” to improve the contrast of the 
picture. 
 Lamp Reset
Reset the lamp hour counter after replacing the lamp.
	When ambient tem-perature is over 35°C in operating, the projector will switch to STD automatically.
  
						

							54English
User Controls
OPTIONS |  
Point Blank
 Interactive
Choose “On” to enable Interactive and activate the Interactive 
menu.
 Pointer Motion
Choose this function to select the Pointer Motion mode: “Normal”, 
“Draw”, and “Stable”.
  Normal: In this mode, press Mouse Left Click  button of 
the interactive pen can hold the position of the pointer for a 
moment. This mode is best to use the Interactive Pen like a 
mouse, i.e., for left click and double click functions. 
  Draw: In this mode, the pointer can move freely for drawing. 
This mode is best for drawing or writing on the screen
  Stable: In this mode, press and hold the Mouse Left Click  
button of the interactive pen to limit the pointer to vertical or 
orizontal moves. If the Mouse Left Click  button is released, 
the pointer can resume to move freely. This mode is best for 
drawing vertical or horizontal lines on the screen. 
 Click Speed
Choose this function to select the mouse pause time. This function 
is only available in Normal mode. The available options are: “Fast”, 
“Medium” and “Low”.
 Set Function
Choose this function to select the function of the Menu  button 
on the interactive pen.
	Interactivity is sup-ported only in the fol-lowing input modes: VGA and HDMI from a PC, and Wire-less Display, USB Display, and LAN Display
	Interactive Pen is not supported in 3D source.   
						

							55English
User Controls
  Pointer Motion: Function as toggling among “Normal”, “Draw”, 
and “Stable” mode
  
PowerPoint Annotation: Function as annotating in the Power-
Point slide show.
  Switch Windows (Alt+Tab): Function as toggling among 
windows,acting as the keyboard shortcut Alt+Tab. 
  Esc: Function as the keyboard Esc button. 
  
Show Desktop (Cmd+D): Function as showing desktop, mini-
mizing all windows.
  Open Windows Explorer (Cmd+E): Choose the function as 
opening the Windows Explorer. 
  
Middle Mouse: Choose the function as the scroll wheel of the 
mouse.
  Double Click: Choose the function as double-clicking. 
  Disable: Disable the Function button.
 Channel
  Auto: Channel is selected automatically. 
  Manual: Channel is selected manually. A total of 15 channels 
are available.
 Information
View the information about the interactive pen. 
						

							56English
User Controls
Ruby is a embedded project which can bring the high perfor-
mance in network projection. Base on network protocol, user 
can configure the projector remotely. It supports to connect the 
PC with Projector by USB, Ethernet, and Wireless. This project 
makes full use of the network capability. It allows the admin-
istrator to control all the projectors in one building by one PC. 
When some emergencies happen, the projector can send out 
alert information to administrator by email and web page. It 
can read more than one USB device directly and show all the 
images in it
This project consists of three software applications which 
make full use of the network and USB capability
• Web Control
• Card Reader
• Optoma Presenter
How to use Web Control 
The Web Control application allows user to configure the projec-
tor remotely base on various network protocol. It is convenient for 
administrator to control the whole projectors in one building by 
one PC.
1. Start the web browser, and enter the IP address of the projector in 
URL: http://IP-address, the log-in web page is displayed.
Ruby Introduction 
						

							57English
User Controls
2 There are 3 options in this page. 
•  Click “Download”, it displays the interface to download the soft-
ware of “Optoma Presenter”.
• Click “Crestron”, to enter the control page of Flash UI.
• Click “Admin”,  the log-in page shows up.
3. Enter the password and click [Login] button, and then main page 
is displayed. The default password is “admin” when target system 
is brand new. The maximum password is 8 characters with any 
characters except “space”.
4.  Click “Logout”, it returns back to log-in page.
  System Status
This page indicates the information of Model Name, Versions, LAN 
Status and Wireless Status.
 General Setup
Password of entering control web page can be changed here. Old 
password is requested when changing a new password.
 Projector Control
All items in this page is the detail options about how to control 
the projector more smoothly. Example: Power On/OFF, Source 
change, Brightness, ….This page will refresh the status currently 
of all the items in few seconds. 
						

							58English
User Controls
 Alert Setup
This page is to set up the alert notification for kinds of error types 
by sending mail. Alert type is multi-options.
 SMTP Mail Setup
This page is to set up the details of mail sending, ex. mail server 
IP address, user name, password and mail address of receivers. 
(Note: Multi-receivers are separated by semicolon.)
 Network Setup
This page is to set up network parameters of IP, DHCP Server, and 
wireless.  
						

							59English
User Controls
•  IP Setup: Click “Obtain an IP address automatically” as auto 
mode; click “Use the following IP Address” as static mode,  IP Ad-
dress/Subnet Mask/Default Gateway/ DNS Server are required to 
be filled and then click “Apply” button.
•  DHCP Server Setup: Enable/Disable, Start IP, End IP, Subnet 
Mask, Default Gateway, DNS server.
•  Wireless Setup: Connect with wireless dongle, and then setup 
WLAN mode, SSID, KEY, Channel etc.
  Presenter Setup
Admin password/User password is used to change the password 
for admin/user in target side.
Click “Connection Control” to enter “Connection Status”
•  Conference Control: Click “On” or “Off” to enable/disable confer-
ence control mode. 
						

							60English
User Controls
 Click the following icons under “Play Control”
•  : Click to disconnect host PC.
•  : Click to switch session to background.
•  : Click to change display region.
 Crestron RoomView
This is the control page of Flash UI.
Click “Power” to control power on/off of projector.
Click “Vol-, Mute, Vol+” to control volume.
In the SourceList, it includes all sources that the projector can 
process. 
Click “Menu” to open menu; click “Source” to choose next source; 
click “Auto” to detect the source automatically; click “Blank” for  AV 
mute function.
“Contrast, Brightness, Color, Sharpness, Zoom, Freeze” can be 
adjusted in the control panel below.