Optoma Ex556 Projector User Manual

							1English
Table of Contents ............................1
Usage Notice ...................................2
Safety Information ...............................2
Precautions  .........................................3
Eye Safety Warnings  ..........................5
Product Features ................................5
Introduction ......................................6
Package Overview  ..............................6
Product Overview  ...............................7
Main Unit ..............................................7
Control Panel  .......................................8
Input/Output Connections ....................9
Remote Control ..................................10
Installation  .....................................11
Connecting the Projector ..................11
Connect to Computer/Notebook ........11
Connect to Video Sources .................12
Powering the projector On / Off  ........13
Powering On the Projector .................13
Powering Off the Projector  .................14
Warning Indicator  ...............................14
Adjusting the Projected Image  ..........15
Adjusting the Projector’s Height ........15
Adjusting the Projector’s Zoom /  Focus  .................................................16
Adjusting Projection Image Size ........16
User Controls  ................................18
Control Panel & Remote Control ......18
Control Panel .....................................18
Remote Control ..................................19
On-screen Display Menus  ................24
How to operate  .................................24
Menu Tree ..........................................25
IMAGE  ...............................................27
IMAGE | Advanced  ............................29
DISPLAY ............................................31
DISPLAY | 3D   ...................................34
SETUP ...............................................35
SETUP | Signal (RGB) .......................37
SETUP | Security  ...............................38
SETUP | Advanced  ............................40
OPTIONS ...........................................41
OPTIONS | Advanced  ........................42
OPTIONS | Lamp Settings .................43
Appendices  ....................................44
Troubleshooting  ................................44
Replacing the lamp ...........................49
Compatibility Modes  .........................51
Computer Compatibility .....................51
Video Compatibility ............................53
RS232 Commands and Protocol  Function List  .....................................54
RS232 Pin Assignments ....................54
RS232 Protocol Function List  ............55
Wall Mount Installation ......................59
Optoma Global Offices  .....................60
Regulation & Safety Notices .............62
Table of Contents 
						

							2English
Usage Notice
Safety Information
The lightning flash with arrow head within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous \
voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Class B emissions limitsThis Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Important Safety Instruction  1. Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from over heating, it is recommended to install the projector in a location that does not block ventilation.  As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the projector in an enclosure such as a book case or a cabinet that restricts air flow.  2. Do not use the projector near water or moisture. To reduce the risk of fire and/or electric shock, do not expose the projector to rain or moisture.  3. Do not install near heat sources such as radiators, heaters, stoves or any other apparatus such as amplifiers that emits heat.  4. Clean only with dry cloth.  5.  Only use attachments/accessories specified by the manufacturer.   6. Do not use the unit if it has been physically damaged or abused.  Physical damage/abuse would be (but not limited to): Unit has been dropped. Power supply cord or plug has been damaged. Liquid has been spilled on to the projector. Projector has been exposed to rain or moisture. Something has fallen in the projector or something is loose inside.Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please call Optoma before you send the unit for repair.  7. Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts that could result in fire or electric shock.  8. See projector enclosure for safety related markings.  9. The unit should only be repaired by appropriate service personnel.   
						

							3English
Usage Notice
Precautions
 
Please follow all warnings, precautions and 
maintenance as recommended in this user’s 
guide.
▀■ Warning- Do not look into the projector’s lens when the lamp is on. The bright light may hurt and damage your eyes.
▀■ Warning- To reduce the risk of fire or electric shock, do not 
expose this projector to rain or moisture.
▀■ Warning- Please do not open or disassemble the projector as 
this may cause electric shock.
▀■ Warning- When replacing the lamp, please allow the unit to 
cool down. Follow instructions as described on pages 
49-50.
▀■ Warning- This projector will detect the life of the lamp itself. 
Please be sure to change the lamp when it shows 
warning messages.
▀■ Warning- Reset the “Lamp Reset” function from the on-screen 
display “OPTIONS | Lamp Settings” menu after 
replacing the lamp module (refer to page 43).
▀■ Warning- When switching the projector off, please ensure 
the cooling cycle has been completed before 
disconnecting power. Allow 90 seconds for the 
projector to cool down.
▀■ Warning- Do not use lens cap when projector is in operation.
▀■ Warning- When the lamp is approaching the end of its lifetime, 
the message “Lamp Warning: Lamp life exceeded.” 
will show on the screen. Please contact your local 
reseller or service center to change the lamp as soon 
as possible.
▀■ Warning- Do not look into or point the laser pointer on your remote control into your or someone’s eyes. Laser 
pointer can cause permanent damage to eyesight. 
	When the lamp reaches the end of its life, the pro-jector will not turn back on until the lamp module has been replaced. 
To replace the lamp, follow the procedures listed under “Replacing the Lamp” section on pages 49-50.  
						

							4English
Usage Notice
Do:
		Turn off and unplug the power plug from the AC outlet before 
cleaning the product.
		Use a soft dry cloth with mild detergent to clean the display 
housing.
		Disconnect the power plug from AC outlet if the product is 
not being used for a long period of time.
Do not:
		Block the slots and openings on the unit provided for 
ventilation.
		Use abrasive cleaners, waxes or solvents to clean the unit.
		Use under the following conditions:
  - In extremely hot, cold or humid environments.
 Ensure that the ambient room temperature is within 
5 - 40°C.
 Relative Humidity is 5 - 40°C, 80% (Max.), 
non-condensing.
    - In areas susceptible to excessive dust and dirt.
   - Near any appliance generating a strong magnetic field.
   - In direct sunlight.  
						

							5English
Usage Notice
Eye Safety Warnings
 
▀■ Avoid staring/facing directly into the projector beam at all 
times. Keep your back to the beam as much as possible.
▀■ When projector is used in a classroom, adequately supervise 
students when they are asked to point out something on the 
screen.
▀■ In order to minimize the lamp power, use room blinds to 
reduce ambient light levels. 
Product Features
▀■ SVGA (800x600) Native resolution / 
XGA (1024x768) Native resolution / 
WXGA (1280x800) Native resolution 
▀■ HD compatible – 720p and 1080p supported 
▀■ VGA monitor loop through 
(works on standby mode > 1W)
▀■ BrilliantColorTM Technology 
▀■ Security Bar and Kensington Lock 
▀■ RS232 control 
▀■ Rapid shutdown 
▀■ Built-in speakers
▀■ Quick Resume and Eco+ mode
	Monitor loop through only sup-port in VGA1-In/YPbPr. 
						

							6English
Introduction
	Due to different applications in each country, some regions may have different accessories.
Power Cord
Package Overview
Unpack and inspect the box contents to ensure 
all parts listed below are in the box. If something 
is missing, please contact your nearest customer 
service center.
2 × AAA Batteries
ProjectorVGA Cable 
IR Remote Control
Documentation : 
	User’s Manual
	Warranty Card
	Quick Start Card
	WEEE Card   (for EMEA only)
	STOP Card   (for US Only)  
						

							7English
Introduction
Product Overview
Main Unit
1. Control Panel
2. Focus Ring
3. Speaker
4. Zoom Ring
5. Lens
6. IR Receiver
7. Input / Output 
Connections
8. Power Socket
9. Tilt-Adjustment Feet
10. Ventilation (inlet)
11. Ventilation (outlet)
3
8
14
9
7
10
562
10
11
	The interface is subject to model’s specifi-cations. 
						

							8English
Introduction
/
/
Control Panel
231
7
1. Power LED
2. Lamp LED 
3. Temp LED
4. Enter / Help
5. Menu
6. Re-Sync
7. Keystone Correction
8. Four Directional Select Keys
9. Source
10. Power/Standby button
510
69
8
4      
						

							9English
Introduction
AUDIO-IN
AUDIO OUT
VGA1-IN 
 / YPbPr
RS-232C
VGA-OUT
VGA2-IN / YPbPr
HDMI
S-VIDEO
 VIDEO
USB
Input/Output Connections
	Monitor loop through only sup-port in VGA1-In/YPbPr.
1. 
USB Connector (Connect to PC for Remote Mouse func-
tion)
2. HDMI Connector
3. Composite Video Input Connector
4. S-Video Input Connector
5. VGA-Out Connector (Monitor Loop-through Output)
6. VGA1-In/YPbPr Connector  
(PC Analog Signal/Component Video Input/HDTV/YPbPr) 
7. RS-232 Connector (9-pin DIN Type)
8. Audio Input connector (3.5mm mini jack)
9. Audio Output Connector (3.5mm Mini Jack) 
10. KensingtonTM Lock Port
11.   VGA2-In/YPbPr Connector  
(PC Analog Signal/Component Video Input/HDTV/YPbPr) 
12. Power Socket
542
12
1
10
38
11
67
9
	The interface is subject to 
model’s specifi-cations. 
						

							10English
Introduction
Remote Control
	The interface is subject to model’s specifi-cations.
1. LED Indicator
2. Power On/Off
3. Source
4. Mouse Left Click
5. Enter
6.   Four Directional Select 
Keys / Mouse control 
7. Switch
8. Re-Sync
9. Mouse Right Click
10. Page Up
11. Page Down
12.  Volume +/-
13. Menu
14. Zoom
15. AV mute
16. Video 
17. 3D
18. VGA
19. USB
20. Laser Pointer
21. Keystone +/-
22. Brightness
23. HDMI
24. S-Video 
25. Contrast 
26.  Numbered keypad 
(for password input) 
27. Freeze
28. Mode
29. Eco+
2
18
27
25
24
5
23
26
21
3
13
6
20
14
10
1
7
8
49
12
17
16
15
19
22
11
28
29