Optoma Ex531p Projector User Manual

English

 Installation
VGA1- IN / SCARTS-VIDEOVIDEORS232AUDIO-OUTAUDIO-INVGA-OUTVGA2- IN
E62405SPR
	Connecting	the	Projector
	Due to the difference in applications for each country, some regions may have different accessories.
	(*) Optional accessory 
	Connect	to	Computer/Notebook

3
.........................................................................\
...........................Power Cord2.........................................................................\...

2English

Installation

VGA1- IN / SCARTS-VIDEOVIDEORS232AUDIO-OUTAUDIO-IN

E62405SPR

VGA-OUT
VGA2- IN

	Connect	to	Video	Sources
.........................................................................\
...........................Power Cord2.........................................................................\
............................VGA Cable 3.........................................................................\
.......*Composite Video...

3English

 Installation

Powering On the Projector
.  Remove the lens cap. 
2. Securely connect the power cord and signal cable. When 
connected, the Power LED will turn red. 
3.  Turn on the lamp by pressing “POWER” button either on the 
top of the projector or on the remote. The Power LED will 
now turn Green. 
  The startup screen will display in approximately 0 seconds. 
The fi rst time you use the projector, you can select your 
preferred language from quick menu after the startup...

4English

Installation

Warning Indicator
 When the “LAMP” indicator lights red (“POWER” indicator 
flashes red), the projector will automatically shut down. 
Please call the nearest Optoma facility for assistance.
  When the “TEMP” indicator lights red (“POWER” indicator 
flashes red), it indicates the projector has overheated. The 
projector will shut down automatically.
  Under normal conditions, the projector can be switched on 
again after it has cooled down. 
 When the “TEMP” indicator...

5English

 Installation

 Adjusting	the	Projected	Image
Adjusting the Projector’s Height 
The	projector	is	equipped	with	elevator	feet	for	
adjusting	the	image	height.
. Locate the adjustable foot you wish to modify on the 
underside of the projector. 
2. Rotate the three adjustable rings counter clockwise to 
raise the projector or clockwise to lower it. Repeat with the 
remaining feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring 

6English

Installation
Adjusting the Projector’s Zoom / Focus
Focus Ring
Zoom Ring
You may turn the zoom ring to zoom in or out. To focus 
the image, rotate the focus ring until the image is clear. 
The projector will focus at distances from 3.9 to 39.4 feet (.2 
to 2.0 meters).
Adjusting Projection Image Size
Hd
68.8(174.8cm)
114.7(291.4cm)
160.6(407.9cm)
206.5(524.5cm)
275.3(699.3cm)
30.3(76.9cm)
75.7(192.3cm)
126.2(320.5cm)
176.7(448.7cm)
227.1(576.9cm)
302.9(796.2cm)
27.5(69.9cm)...

7English

 User Controls
Control Panel
 Control Panel & Remote Control
There	are	two	ways	for	you	to	control	the	functions:	
Control	Panel	and	Remote	Control.
Using the Control Panel
POWERRefer to the “Power On/Off the Projector” section on 
pages 3-4.
MENUPress “MENU” to launch the on-screen display 
(OSD) menu. To exit OSD, Press “MENU” again.
Confi rm your item selection.
RE-SYNCAutomatically synchronize the projector to the input 
source.
SOURCEPress “SOURCE” to select an input...

8English

User Controls

Remote Control
Using the Remote Control
Power  
Refer to the “Power On/Off the Projector” 
section on pages 3-4.
 Confi rm your item selection.
SourcePress “SOURCE” to select an input signal.
Re-SYNC Automatically synchronizes the projector to 
the input source.
Four Directional 
Select KeysUse     to select items or make 
adjustments to your selection.
Keystone +/-Adjust image distortion caused by tilting the 
projector.
Volume +/-Adjust to increase / decrease...

9English

 User Controls

Remote Control
Using the Remote Control
ContrastControl the degree of difference between 
the lightest and darkest parts of the picture.
FreezePress “Freeze” to pause the screen image.
Press this button again to unlock.
AV muteMomentarily turns off/on the audio and 
video.
S-Video Press “S-Video” to choose S-Video source.
VGAPress “VGA” to choose VGA sources.
VideoPress “Video” to choose Composite video 
source. 

20English

User Controls

The	Projector	has	multilingual	On-screen	Display	menus	that	
allow	you	to	make	image	adjustments	and	change	a	variety	of	
settings.	The	projector	will	automatically	detect	the	source.	
How to operate 
.  To open the OSD menu, press “MENU” on the Remote Control or 
Projector Keypad.
2  When OSD is displayed, use   keys to select any item in the 
main menu. While making a selection on a particular page, press 
 or “Enter” key to enter sub menu.
3. Use   keys to select the...