Optoma Ep759 Projector User Manual

11... English
Installation
Power/
Standby1
Powering On the Projector
1.Remove the lens cap.
2.Ensure that the power cord and signal cable are securely
connected.  The Power LED will turn red.
3.Turn on the lamp by pressing “Power/Standby” button on
the control panel. n
The startup screen will display for 30 seconds and the Power
LED will flash green.
When the startup screen disappears, the Power LED will turn
green.
4.Turn on your source (computer, notebook, video player ,etc.).
The projector will detect...

12English ...
Installation
Warning Indicator
™When the “TEMP” indicator turns red, it indicates the projector has
overheated. The projector will automatically shut itself down. See
page 31.
™When the “LAMP” indicator flashes red (0.5 second intervals), it
indicates a problem with the lamp.  Turn off the projector and
disconnect the power cord from the electrical outlet, then contact
your local dealer or our service center. See page 31.
™When the “LAMP” indicator flashes red (1 second intervals), it...

13... English
Adjusting the Projected Image
Adjusting the Projector Image Height
Tilt Adjusting Wheel
Elevator Foot 12
3
Elevator Button
The projector is equipped with an elevator foot for adjusting
the image height.
To raise the image:
1.Press the elevator button 
n.
2.Raise the image to the desired height angle o, then release
the button to lock the elevator foot into position.
3.Use 
p to fine-tune the display angle.
To lower the image:
1.Press the elevator button.
2.Lower the image, then release the...

14English ...
Max.29.5(75.0cm)73.8(187.5cm)123.0(312.5cm)172.2(437.5cm)196.9(500.0cm)300.0(762.0cm)
Min.  24.6(62.5cm)  61.5(156.3cm) 102.5(260.4cm)  143.5(364.6cm) 164.0(416.7cm)  250.1(635.2cm)
Max.(WxH)23.60 x 17.70
(60.0 x 45.0cm)59.04 x 44.28
(150.0 x 112.5cm)98.40 x 73.80
(250.0 x 187.5cm)137.76 x 103.32 (350.0 x 262.5cm)157.52 x 118.14
(400.0 x 300.0cm)240.00  x 180.00
(609.6 x 457.2cm)
Min.(WxH) 19.68 x 14.76
(50.0 x 37.5cm) 49.20 x 36.90
(125.0 x 93.8cm) 82.00 x 61.50
(208.3 x 156.2cm) 114.80 x...

15... English
User Controls
Remote Control Control Panel
Control Panel & Remote Control
There are two ways for you to control the functions: Remote
Control and Control Panel.
Using the Control Panel
Power/Standby  
4Refer to the “Power On/Off the Projector” section on pages
11-12.
Source  
4Press “Source” to choose RGB, Component-p, Component-i,
S-Video, Composite Video and HDTV sources.
Menu 
4Press “Menu” to launch the on screen display (OSD) menu.
To exit OSD, press “Menu” again.
Keystone    /...

16English ...
User Controls
Using the Remote Control
Power  
4Refer to the “Power On/Off the Projector” section on pages
11-12.
Sync
4Automatically synchronizes the projector to the input source.
Keystone
4Adjusts image distortion caused by tilting the projector (±16
degrees).
Display Format
4Display the “Display Format” section of the onscreen display
menu to select the desired aspect ratio.
Laser Button  
4Aim the remote at the viewing screen, press and hold this
button to activate the laser pointer....

17... English
OK  
4Confirm your selection of items.
Source Lock
4Select auto detection all connector ports or lock current
connector port.
Menu  
4Press “Menu” to launch the on screen display menu.  To exit
OSD, press “Menu” again.
VGA
4Press “VGA” to change source to VGA-In connector.  This
connector supports Analog RGB, YPbPr (480p/576p/720p/
1080i), YCbCr (480i/576i) and RGBsync.
DVI-I
4Press “DVI-I” to change source to DVI-I connector.  This
connector supports Digital RGB, Analog RGB, YPbPr (480p/...

18English ...
The Projector has multilingual On Screen Display menus
that allow you to make image adjustments and change a
variety of settings. The projector will automatically detect
the source.
How to operate
1.To open the OSD menu, press “Menu ” on the Remote Control
or Control Panel.
2.When OSD is displayed, use     keys to select any item in the
main menu.  While making a selection on a particular page, press
 key to enter sub menu.
3.Use      keys to select the desired item and adjust the
settings...

19... English
Language
Language
Choose the multilingual OSD menu . Use the   or  key to select
your prefered language.
Press “Menu” to finalize the selection.
Computer / Video Mode
User Controls
LanguageManagement PIP Image - I Image - IIAudio     

20English ...
Image-I
(Computer Mode)
Brightness
Adjust the brightness of the image.
4Press the  to darken image.
4Press the  to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes
the amount of black and white in the image.
4Press the  to decrease the contrast.
4Press the  to increase the contrast.
Frequency
“Frequency”changes the display data frequency to match the
frequency of your computer’s...