Optoma Ep719 Projector User Manual

							11... English
™To ensure the projector works well with your computer, please
set the display mode of your graphic card less than or equal to
1024 X 768 resolution. Make sure the timing of the display mode is
compatible with the projector.  Refer to the “Compatibility Modes”
section on page 38.
S-Video OutputVideo Output DVD Player,
Settop Box,
HDTV receiver
6
8
1
7
RGB
1. .............................................................................................................Power Cord
2. ..............................................................................................................VGA Cable
3. .................................................................................................DVI to  VGA Cable
4. ................................SCART RGB/S-Video Adaptor (For European Use Only)
5. .........................................................................................Composite Video Cable
6. ....................................................................S-Video Cable (Optional Accessory)
7. .....................................D-15 to RCA Adapter for YPbPr (Optional Accessory)
8. ..........................................................................USB Cable (Optional Accessory)
USB
5
USA
323
4
Connecting the Projector
Installation
™Due to the differ-
ence in applica-
tions for each
country, some
regions may have
different
accessories.       
						

							12English ...
Installation
Powering On the Projector
1.Remove the lens cap. n
2.Ensure that the power cord and signal cable are securely
connected.  The Power LED will flash green.
3.Turn on the lamp by pressing “Power/Standby” button on
the control panel.o And the Power LED will turn green.
The first time you use the projector, you can select your
prefered language from quick menu after the startup
screen display.
4.Turn on your source (computer, notebook, video player,
etc.).  The projector will detect your source automatically.
™If you connect multiple sources at the same time, use the
“Source” button on the control panel or remote control to
switch.
Powering On/Off the Projector
™Turn on the
projector first and then
the signal sources.
1
Power/Standby
2
Lens Cap
Quick Menu           
						

							13... English
Warning Indicator
™When the “LAMP” indicator lights solid red, the projector will
automatically shut itself down. Please contact your local
reseller or service center. See page 35~36.
™When the “TEMP” indicator lights solid red for about 10
seconds, it indicates the projector has been overheated. The
projector will automatically shut itself down.
Under normal conditions, the projector can be switched on
again after it has cooled down.  If the problem persists, you
should contact your local dealer or our service center. See page
35~36.
™When the “TEMP” indicator flashs red for about 5 seconds, it
indicates the fan failed. Please contact your local dealer or our
service center. See page 35~36.
Powering Off the Projector
1.Press the “Power/Standby” button to turn off the projector
lamp, you will see a message
“
” displayed on the
projector’s screen. Press the “Power/Standby” button
again to confirm, otherwise the message will disappear
after 5 seconds.
Please note that if the 
 key is pressed instead,  the projec-
tor will enter the “Picture Mute” mode and no image will
be displayed.  To exit the “Picture Mute” mode, press the
“Power/Standby” button again.
2.The cooling fans continue to operate for about 30 seconds
for cooling cycle and the Power LED will turn green.  When
the Power LED begins flashing, the projector has entered
standby mode.
If you wish to turn the projector back on, you must wait
until the projector has completed the cooling cycle and has
entered standby mode.  Once in standby mode, simply
press “Power/Standby” button to restart the projector.
3.Disconnect the power cord from the electrical outlet and
the projector.
4.Do not turn on the projector immediately following a
power off procedure.
Installation     
						

							14English ...
Installation
Adjusting the Projected Image
Adjusting the Projector Image Height
Tilt Adjusting
Wheel Elevator Foot
23
Elevator Button
The projector is equipped with an elevator foot for adjusting
the image height.
To raise the image:
1.Press the elevator button 
n.
2.Raise the image to the desired height angle o, then release
the button to lock the elevator foot into position.
3.Use 
p to fine-tune the display angle.
To lower the image:
1.Press the elevator button.
2.Lower the image, then release the button to lock the elevator
foot into position.
3.Use 
p to fine-tune the display angle.
 1
3     
						

							15... English
69.3
(176.1cm)115.6
(293.5cm)161.8
(410.9cm)184.9
(469.6cm)231.1
(587.0cm)
38.1 
(96.8cm)76.2
(193.6cm)127.1
(322.7cm)177.9
(451.8cm)203.3
(516.3cm)254.1
(645.4cm)
4.92
32.81 26.25 22.97 16.409.84(1.5m)
(10.0m) (8.0m) (7.0m) (5.0m) (3.0m)34.7
(88.1cm)
Max.38. 1(96.8cm)76. 2(193. 6cm)127.1(322.7cm)177.9(451.8cm)203.3(516.3cm)254.1(645.4cm)
Min. 34. 7(88.1cm) 69. 3(176. 1cm) 115. 6( 293. 5cm) 161.8(410.9cm) 184.9(469.6cm) 231.1(587.0cm)
Max.(WxH)30. 48 x 22.86
(77. 4 x 58. 1cm)60. 96 x 45.72
(154.9 x 116.2cm)101.68 x 76.26
(258.2 x 193. 6cm)142.32 x 106.74
(361.4 x 271. 1cm)162.64 x 121.98
(413.0 x 309. 8cm)203.28 x 152.46
(516.3 x 387. 2cm)
Min.(WxH)27. 76 x 20.82
(70. 5 x 52. 9cm)55. 44 x 41.58
(140.9 x 105. 7cm)92. 48 x 69.36
(234.8 x 176. 1cm)129.44 x 97.08
(328.7 x 246. 5cm)147.92 x 110.94
(375.7 x 281. 8cm)184.88 x 138.66
(469.6 x 352. 2cm)
4.92(1.5m)9.84(3.0m)16. 40(5. 0m)22.97(7.0m)26. 25(8. 0m)32.81(10.0m)
Screen
(Diagonal)
Screen
Size
Distance
Diagonal
Focus RingZoom Lever
Adjusting the Projector Zoom / Focus
You may turn the zoom lever to zoom in or out.  To focus the
image, rotate the  focus ring until the image is clear. The projec-
tor will focus at distances from 4.9 to 32.8 feet (1.5 to 10.0 meters).
Adjusting Projection Image Size
™This graph is for user’s reference only.
Installation       
						

							16English ...
Remote Control Control Panel
Control Panel & Remote Control
There are two ways for you to control the functions: Remote
Control and Control Panel.
Using the Control Panel
Power/Standby  
4Refer to the “Power On/Off the Projector” section on pages
12-13.
Source
4Press “Source” to choose RGB, Component-p, Component-i,
S-Video, Composite Video and HDTV sources.
Menu 
4Press “Menu” to launch the on screen display (OSD) menu.
To exit OSD, press “Menu” again.
Keystone   / 
4Adjusts image distortion caused by tilting the projector (±8
degrees).
Four Directional Select Keys
4Use         to select items or make adjustments to
your selection.
Enter  
4Confirm your selection of items.
Re-Sync
4Automatically synchronizes the projector to the input source.
Installation         
						

							17... English
Installation
Using the Remote Control
Power
4Refer to the “Power On/Off the Projector” section on pages
12-13.
Re-Sync
4Automatically synchronizes the projector to the input source.
Volume + / - (Vol+/Vol-)
4Increases/decreases speaker volume.
Reset
4Changes the adjustments and settings to the factory default
value.
Hide
4Press “Hide” to hide image, press again to restore display of the
image.
Keystone   / 
4Adjusts image distortion caused by tilting the projector (±15
degrees).
Freeze
4Press “Freeze” to pause the screen image.
D-Zoom
4Press “D-Zoom” button to zoom in of an image.
Display Mode
4Select the display mode from PC, Movie, Game, sRGB and User.
Four Directional Select Keys
4Use         to select items or make adjustments to
your selection.
Enter
4Confirm your selection of items.
Menu
4Press “Menu” to launch the on screen display menu.  To exit
OSD, press “Menu” again.
VGA1
4Press “VGA1” to choose VGA1 connector.
VGA2
4Press “VGA2” to choose VGA2 connector.
S-Video
4Press “S-Video” to choose S-Video source.
EU
EU   
						

							18English ...
Composite
4Press “composite” to choose Composite video source.
VGA
4Press “VGA” to choose VGA connector.
DVI-D
4Press “DVI-D” to choose DVI connector.
Installation
USA
USA   
						

							19... English
The Projector has multilingual On Screen Display menus
that allow you to make image adjustments and change a
variety of settings. The projector will automatically detect
the source.
How to operate
1.To open the OSD menu, press “Menu ” on the Remote Control
or Control Panel.
2.When OSD is displayed, use     keys to select any item in the
main menu.  While making a selection on a particular page, press
 or “Enter” key to enter sub menu.
3.Use      keys to select the desired item and adjust the
settings by 
    key.
4.Select the next item to be adjusted in the sub menu and adjust as
described above.
5.Press “Menu ” to confirm, and the screen will return to the main
menu.
6.To exit, press “Menu ”again.  The OSD menu will close and the
projector will automatically save the new settings.
On Screen Display Menus
Main Menu
Sub Menu
Setting
User Controls     
						

							20English ...
User Controls
Menu Tree