Optoma Eh1020 Projector User Manual

English

 Installation
	Connecting	the	Projector
	Connect	to	Computer/Notebook
.........................................................................\
...........................Power Cord2.........................................................................\
...........................*USB Cable 3.........................................................................\
............................VGA Cable4.........................................................................\...

2English

Installation

VGA-OUTS-VIDEOVIDEO
AUDIO-OUTRS-232USBAUDIO-IN-LHDMIAUDIO-IN
12V OUT
SCART / YPbPr /VGA-INAUDIO-IN-R(VGA)(S-VIDEO/VIDEO)(S-VIDEO/VIDEO)

E62405SP
R

	Connect	to	Video	Sources
.........................................................................\
...........................Power Cord2.........................................................................\
.......*Composite Video Cable3........................................................................\...

3English

 Installation

	Powering	the	projector	On	/	Off
	Turn on the projector fi rst and then select the signal sources.
Powering On the Projector
.  Remove the lens cap. 
2. Securely connect the power cord and signal cable. When 
connected, the ON/STANDBY LED will turn Amber. 
3.  Turn on the lamp by pressing “” button either on the top of 
the projector or on the remote. The ON/STANDBY LED will 
now turn Green. 
  The startup screen will display in approximately 0 seconds. 
The fi...

4English

Installation

	Contact the nearest service center if the projector displays these symptoms. See pages 57-58 for more information.
Warning Indicator
When the warning indicators (see below) come on, 
the projector will automatically shutdown: 
 “LAMP” LED indicator is lit red and if “On/Standby” indicator 
flashes amber.
  “TEMP” LED indicator is lit red and if “On/Standby” 
indicator flashes amber. This indicates the projector has 
overheated. Under normal conditions, the projector can...

5English

 Installation

 Adjusting	the	Projected	Image
Adjusting the Projector’s Height 
The	projector	is	equipped	with	elevator	feet	for	adjusting	
the	image	height.
. Locate the adjustable foot you wish to modify on the 
underside of the projector. 
2. Rotate the adjustable ring counter clockwise to raise 
the projector or clockwise to lower it. Repeat with the 
remaining feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring 

6English

Installation
Adjusting the Projector’s Zoom / Focus
You may turn the zoom lever to zoom in or out. To focus the 
image, rotate the focus ring until the image is clear. 
 .2x Zoom series will focus at distances from 4.92 to 32.8 
feet (.50 to 0.00 meters).
POWER
?
Focus Ring
Zoom Ring
Adjusting Projection Image Size
Hd
62.7(159.3cm)
81.5(207.1cm)
125.4(318.6cm)
200.8(510.0cm)
301.2(764.9cm)
45.2(114.7cm)
75.3(191.2cm)
97.8(248.5cm)
150.5(382.4cm)
240.9(612.0cm)...

7English

 User Controls
Control Panel
 Control Panel & Remote Control
Using the Control Panel
PowerRefer to the “Power On/Off the Projector” section on 
pages 3-4.
RE-SYNCAutomatically synchronize the projector to the input 
source.
 EnterConfi rm your item selection.
SOURCEPress “SOURCE” to select an input signal.
MenuPress “Menu” to launch the on-screen display 
(OSD) menu. To exit OSD, Press “Menu” again.
?HELPHelp Menu (refer to page 20). 
Four Directional 
Select KeysUse     to...

8English

User Controls

Remote Control
Using the Remote Control
Power  
Refer to the “Power On/Off the Projector” 
section on pages 3-4.
Laser   Press to use laser pointer.
L ButtonMouse left click.
R ButtonMouse right click.
Page +Use this button to page up.
Page -Use this button to page down.
Enter/Help Confi rm your item selection.
 ?   Help Menu (refer to page 20). 
SourcePress “Source” to select an input signal.
Re-SYNC Automatically synchronizes the projector to 
the input source....

9English

 User Controls

Remote Control
Using the Remote Control
HDMIPress “HDMI” to choose HDMI source.
FreezePress “Freeze” to pause the screen image.
Press this button again to unlock.
AV muteMomentarily turns off/on the audio and 
video.
S-Video Press “S-Video” to choose S-Video source.
VGAPress “VGA” to choose VGA sources.
VideoPress “Video” to choose Composite video 
source.
/? 

20English

User Controls

 Using the HELP button
The HELP function ensures easy setup and operation. 
 Press the “?” button on the control panel to open the Help 
Menu. 
POWER
?
POWER
?