Olympus Vp 1 Projector User Manual
Have a look at the manual Olympus Vp 1 Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 18 Olympus manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
E-31 Projecting a Picture in Picture This function displays the video image (i.e., the picture of the VIDEO connector input) on the personal computer screen (i.e., the PC connector input screen) as a sub-picture. Each press of the PIP button advances the screen size of the sub-picture one step in the sequence of On → Off (i.e., the sub-picture display is off), and then repeats. Note * The main picture is termed the Analog RGB, Digital RGB, or YPbPr input screen, whereas the sub-picture is termed the VIDEO, S-VIDEO, and YCbCr input screen. * The sub-picture cannot be displayed when the main screen receives the image from the VIDEO connector. * The sub-picture cannot be displayed when picture in picture is set to off. * To change the display position of the sub-picture, see “Picture in Picture” on Page E-54. Sub-picture Main-picture ON OFF FREEZE MUTE PIP DIGITAL RGB YPbPr VIDEO S-VIDEO YCbCr QUICK ASPECT AUTOPOWER General Operation Freezing a Moving Picture This function is used to stop and view a moving picture. Note that the input image continues to advance even though the picture there is a still picture condition. To change the screen to a still image, press the FREEZE but- ton. Press the button again to return to the moving picture. Note During a picture in picture display, both the main picture and the sub- picture become still pictures. ON OFF FREEZE MUTE PIP DIGITAL RGB YPbPr VIDEO S-VIDEO YCbCr QUICK ASPECT AUTOPOWER Suspending Video and Audio Temporarily This function is used to cancel the video and audio at the same time. Press the MUTE button to cancel the video and the audio. A further press brings a return to the original condition.ON OFF FREEZE MUTE PIP DIGITAL RGB YPbPr VIDEO S-VIDEO YCbCrPOWER
E-32 General Operation Using the Quick Menu This function permits commonly used adjustments to be performed quickly. Note that the Quick Menu will not be displayed unless the signal of the connected equipment is input. Please select the input that you wish to adjust. Main unit operation (1) A press of the QUICK MENU button brings up the quick ad- justment display. Further presses allow selection of the de- sired adjustment display. (2) Press the or button to make the adjustment. (3) To close the display immediately, press the MENU button. In the absence of operations for a period of about 10 sec- onds, the display will close automatically. Remote control operation (1) A press of the QUICK button brings up the quick adjustment display. Further presses cause the adjustment display to change in sequence. The adjustment display can be selected with use of either the cursor or button. (2) Press the cursor or button to make the adjustment. (3) To close the display immediately, press the CANCEL button. In the absence of operations for a period of about 10 sec- onds, the display will close automatically. MENU AUTO SOURCE QUICK MENU QUICK ENTER MENU ASPECT AUTO HKSTNVKSTN CANCEL (1) (3) (2)
E-33 General Operation Brightness Adjusts the brightness of the image. Brightness decreases in the (–) direction and increases in the (+) direction. Contrast Adjusts the contrast of the image. Contrast becomes less distinct in the (–) direction and more pronounced in the (+) direction. V Keystone Corrects (vertical) keystone distortion of the screen. Adjusts the left and right edges of the screen so that they are parallel. H Keystone Corrects (horizontal) keystone distortion of the screen. Adjusts the up and down edges of the screen so that they are parallel. Picture in Picture The picture from the VIDEO jack is displayed as a sub-picture on the input screen from the PC connector. This function selects either the size of the sub-picture on or off (i.e., no display). (Neither the adjustment display nor the picture will be output unless the signal is input to the PC connector.) See Page E-54 for information about changing the display position of the sub-picture. Volume This function adjusts the volume of the built-in speaker. The volume decreases in the (–) direction and increases in the (+) direction. Quick Color Adj. Select the preset color mode. See Page E-49. Content of Adjustments and Settings Example: Brightness adjustment display + –Brightness0 Display ItemAdjustment/Setting
E-34 General Operation Correcting Keystone Distortion of the Projection Screen This adjustment is used when the projection screen is dis- torted. Note that extreme distortion cannot be corrected and in such cir- cumstances the projector should be placed to face the screen straight on beforehand. ENTER ZOOM MENU HKSTNVKSTN VOL CANCEL (3) (1) (1) (2) Adjustment Method(1) To adjust up-down distortion (e.g., Screen Example 1), press the HKSTN button. The horizontal keystone adjustment dis- play will appear. Note * The keystone adjustment values can be overwritten and saved. See “Keystone” on Page E-53. * Overcompensation of the horizontal keystone correction value will result in a narrowing of the vertical keystone adjustment range. Likewise, overcompensation of the vertical keystone correction value results in a narrowed horizontal adjustment range. * Note that the adjustment range will differ depending on the adjustment conditions. * The screen examples have been depicted in an exaggerated form to aid in description. Screen Example 1 Screen Example 2 Screen Example 3 + –V Keystone0 To adjust left-right distortion (e.g., Screen Example 2), press the VKSTN button. The vertical keystone adjustment display will appear. (2) While viewing the screen, press the (+) button or the (–) but- ton and adjust the vertical or horizontal edges to be parallel. In Screen Example 3, horizontal and vertical keystone distor- tion should be adjusted. (3) To close the display immediately, press the CANCEL button. In the absence of operations for a period of about 10 sec- onds, the display will close automatically. + –H Keystone0
E-35 General Operation Enlargement of the Image and Video Movement This function digitally enlarges the personal computer image and video image (up to 10 times). (1) Press the ZOOM button. The zoom selection display will appear. ENTER ZOOM MENU HKSTNVKSTN VOL CANCEL (4)(3) (1) (2) + –Zoom0 (2) Enlarge to the desired size. Each press of the (+) button enlarges the image and each press of the (–) button makes the image smaller (returning it to 1:1). (3) Pressing the cursor ( ) buttons at the time of the zoom operation will cause the display position to move. (There will not be any movement when zoom is at 0.) (4) To close the display immediately, press the CANCEL button. In the absence of operations for a period of about 10 sec- onds, the display will close automatically. (1) (2) (3) (No enlargement) (Approximately 2 times enlargement) (Movement) Note After magnifying the image, be sure to use the ZOOM button to bring the gauge value back to “0”. The image can also be moved in the following circumstances.* When “Aspect” is set to “Real” by the signal of the personal computer, and the input resolution is higher than the display resolution of the projector. * When “Aspect” is set to “Zoom” by the video signal. Note * Zoom and image movement functions are cancelled when the input is switched. * The greater the zoom enlargement, the less distinct the image will appear. The reason for this is that the dots are being digitally corrected so that they are not conspicuous. * Movement of the screen will not be possible when the menu screen is being displayed.
E-36 General Operation Adjustment of the Volume This function adjusts the volume of the built-in speaker. (1) Press the VOL button. The volume adjustment display will appear. ENTER ZOOM MENU HKSTNVKSTN VOL CANCEL (3) (2) (1) + –Volume53 (2) Adjust the volume. The (+) button increases the volume and the (–) button de- creases the volume. (3) To close the display immediately, press the CANCEL button. In the absence of operations for a period of about 10 sec- onds, the display will close automatically. Note When an image is not being projected, there will not be any sound even if the volume is adjusted.
E-37 Menu Operation Method This section describes only the menu operation method. Please see this page should you need infor- mation while performing menu operations. For information about a menu function, adjustment, or setting, please see one of the pages containing such descriptions. Adjustments and settings are made by projecting an image and adjusting to an optimum condition. The remote control should be pointed toward the remote control sensor of the projector and operated. To return the various items that have been changed via the menu to their standard values (i.e., default values at time of shipping from the factory), see “Factory Default” on Page E-59. (Some items will not return to their initial values.) The adjustment/setting items and contents will differ depending on the input selection and the adjust- ment/setting items that can be used with the input signal are displayed on the menu. Names and Functions of the Parts Names and Functions of the Remote Control Buttons that Operate Via a Menu ON OFF FREEZE MUTE PIP DIGITAL RGB YPbPr VIDEO S-VIDEO YCbCr QUICK ENTER ZOOM CANCELMENU ASPECT AUTO POWER HKSTNVKSTN VOL MENU button Used for menu display and menu closure. Cursor ( ) buttons Used in the selection of menu names and item names as well as in setting and adjusting the item contents. CANCEL button Used to return to menu name selection as well as to close the menu (and the sub menu display). ENTER button Used to set the verification display.
E-38 Menu Operation Method Names and Functions of the Main Unit Buttons Used in Menu Operation MENU AUTO SOURCE QUICK MENUSTATUS POWER POWER MENU button Used to display menus, to return to menu name selections, and to close menus (i.e., closing sub menu displays). Also serves the function of the remote control CANCEL button. (AUTO) button Advances the selection of menu names. Advances the setting/ adjustment values of the item contents. Also serves the function of the remote control ENTER button. (QUICK MENU) button Used in the selection of item names. (SOURCE) button Returns to the selection of menu names. Advances the setting/ adjustment values of the item contents. Names and Functions of Menu Screen Parts Info. Setup View Color Image Aspect Filter ProjectionAuto 3 Keystone V Keystone H Keystone Keystone SaveOff –+0 –+0 Menu Names These are the menu titles. When a menu is selected, the display changes to the title screen. The selected menu name appears in red.Cursor (dark blue) The setting/adjustment of the cursor position can be performed. Item Name The name of the ad- justment/setting Sub Menu Adjustment bar setting contents Adjustment bar: Indicates the adjustment condition by increases or decreases in bar length Setting contents: Displays the set contents Icon: Displays the sub menu or setting contents
E-39 Menu Operation Method Performing Menu Operations The menu operations of the main unit buttons differ from those of the remote control buttons. When both the main unit and remote control button operations are the same, the operation is de- scribed under the remote control operation; however, only when different, the operation will also be described under “Main unit operation”. When a signal is not being input, only “Color”, “Setup” and “Info.” can be selected. (“Color” can be selected for Video and S-Video source only.) When a button is pressed and the next button operation is not entered within 30 seconds, the menu display will close. Adjustment and settings values will be maintained in storage even when the power has been switched off or the power plug has been disconnected. (Note that some items are not stored.) Preparation Switch on the power of the connected equipment, start the play operation or an- other operation, and input the signal to the projector. Select the input that you wish to adjust. The menu display of the description diagram depicts an example in which the “H Key- stone” item name is selected. 1Press the MENU button to display the menu Menu Display ENTER CANCELMENU HKSTNVKSTN Info. Setup View Color Image Brightness–+ Contrast Color Tint Sharpness Reset 0 0 0 0 0–+ –+–+–+ The menu name that existed when the menu was closed previously will be displayed. Note A press of the main unit MENU button will change the function of the SOURCE button, AUTO button, and QUICK MENU button to that of cursor buttons.
E-40 Info. Setup View Color Image Aspect Filter ProjectionAuto 3 Keystone 2Press the cursor ( ) button to select the menu name Selection of the Menu Name ENTER CANCELMENU HKSTNVKSTN Red Each press of the cursor () button advances the selection one step in the sequence of “Color” → “View” → “Setup” → “Info.” → “Image”. Each press of the cursor () button causes a return of one step. The selected menu name will appear in red. Note At the time of menu name selection, check that the item name cursor is not being displayed. To cancel the display of the cursor, press the CANCEL button on the remote control or the MENU button on the main unit. 3Press the cursor () button to display the cursor Displaying the Cursor ENTER CANCELMENU HKSTNVKSTN Info. Setup View Color Image Aspect Filter ProjectionAuto 3 Keystone Cursor: Dark blue This condition allows selection of the item name. Menu Operation Method