OKI C710dtn User Manual

							31 – C710n User’s Guide
System 
Adjust Power Save Time 
Default: 5
Select from 5/10/15/30/60 
Minutes. Select by scroll and Enter 
button.
Clearable 
Warning
Default: ONLINE
Select from: ONLINE/Job. Select by 
scroll and Enter button. PS job only.
Auto Continue
Default: Off
Select from On/Off. Select by scroll 
and Enter button.
Manual Timeout 
Default: 60
Select fro  Off/30 seconds/60 
seconds.
Select by scroll and Enter button.
Wait Timeout
Default: 40
Select from Off/5/10/20/30/40/
50/60/90/120/150/180/210/
240/270/300 seconds. Select by 
scroll and Enter button.
Low Toner
Default: 
Continue
Select action to take when toner 
sensor indicates low toner. Select 
from Continue/Stop (default 
condition indicated by
 * Select by 
scroll and Enter button.
Jam Rcovery
Default: On
Select from On/Off. Select by scroll 
and Enter button.
Error Report
Default: Off
Select from On/Off (default 
condition indicated by
 *). Select by 
scroll and Enter button.
Print Position 
Adjust
Default: 0.00
Select from X Adjust/Y Adjust/
Duplex X Adjust/Duplex Y adjust 
(default condition indicated by
 *). 
Select by scroll and Enter button. 
Define measurement.
ITEMACTIONEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							32 – C710n User’s Guide
System 
Adjust
 
(cont.)
Paper Black 
Settings -2/-1/0/
+1/+2
Default: 0
Used for fine adjustment of the black 
print on paper.
Paper color 
Settings-2/-1/0/
+1/+2
Default: 0
Used for fine adjustment of the color 
print on paper.
Trans. Black 
Settings -2/-1/0/
+1/+2
Default: 0
Used for fine adjustment of the black 
print on transparencies.
Trans. color 
Settings -2/-1/0/
+1/+2
 
Default: 0
Used for fine adjustment of the color 
print on transparencies.
SMR Setting +3/
+2/+1/- /-2/-3
Default: 0
To correct variations in print results 
caused by temperature/humidity 
conditions and difference in print 
density/frequency. Change the 
setting when print quality is uneven.
BG Setting
+3/+2/+1/-1/-2/
-3
Default: 0
To correct variations in print results 
caused by temperature/humility 
conditions and difference in print 
density/frequency. Change the 
setting when background is dark.
Drum Cleaning
Default:Off
Sets whether to rotate the drum in 
idle prior to printing in order to 
reduce horizontal white lines. This 
will shorten the ID life by as much as 
this rotation. Select by scroll and 
Enter button.
Hex Dump
Execute
Prints out data received from the 
host PC in the hexadecimal Dump. 
Turning off the power supply switch 
restores Normal Mode.
ITEMACTIONEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							33 – C710n User’s Guide
Shutdown menu
This menu only appears if the hard disk drive is installed.
This item should always be selected before switching the printer 
off, to ensure that no hard disk data is lost.
Admin Setup
ITEMSETTINGSEXPLANATION
Shutdown 
StartExecute Performs controlled shutdown of the printer, 
ensuring that all files on the internal hard 
disk are closed before power is turned off. 
Only power the printer off when the display 
indicates that shutdown is complete.
ITEMSETTINGSEXPLANATION
Enter 
PasswordxxxxxxxxxxxxEnter a password to gain entry 
to the Admin Setup menu.
Password should be from 6 to 
12 digits of alpha/numeric 
characters (or mix) 
The default value is aaaaaa
Network 
SetupTCP/IPEnable
Disable
Sets TCP/IP Protocol.
Enable: TCP/IP Protocol is 
available.
Disable: TCP/IP Protocol is not 
available.
IP VersionIP v4
IP v4+v6
Set up the IP version.
Operates with IPv4 for IPv4 
(not valid with IPv6).
Operates with both IPv4 and 
IPv6
NetBEUIEnable
Disable
Sets Enable/Disable of NETBEUI 
Protocol.
Downloaded From ManualsPrinter.com Manuals 
						

							34 – C710n User’s Guide
Network 
Setup 
(cont.)NetWareEnable
Disable
Sets Enable/Disable of NetWare 
Protocol.
EtherTalkEnable
Disable
Sets Enable/Disable of 
EtherTalk Protocol.
Frame 
Ty p eAuto
802.2
802.3
Ethernet II
SNAP
Sets the frame type.
Netware should be enabled.
Ty p e I P  
Address 
SetAuto
Manual
Sets the IP Address setting 
method.
TCP/IP should be enabled.
IP Addressxxx.xxx.xxx.xx
xSets the IP Address.
TCP/IP should be enabled.
Subnet 
Maskxxx.xxx.xxx.xx
xSets the Subnet Mask.
TCP/IP should be enabled.
Gateway 
Addressxxx.xxx.xxx.xx
xSets the Gateway (default 
router) address.
 
0.0.0.0 means that there is no 
router.
 
TCP/IP should be enabled.
WebEnable
Disable
Sets Enable/Disable of Web.
Enable: Web/IPP is available. 
Disable: Web/IPP is not 
available.
 
TCP/IP should be enabled.
Te l n e tEnable
Disable
Sets Enable/Disable of Telnet.
Enable: Telnet is available. 
Disable: Telnet is not available. 
TCP/IP should be enabled.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							35 – C710n User’s Guide
Network 
Setup 
(cont.)FTPEnable
Disable
Sets Enable/Disable of FTP.
Enable: FTP is available. 
Disable: FTP is not available. 
TCP/IP should be enabled.
SNMPEnable
Disable
Sets Enable/Disable of SNMP.
Enable: SNMP is available. 
Disable: SNMP is not available. 
TCP/IP or NetWare should be 
enabled.
Network 
ScaleNormal
Small
When Normal is selected, the 
network can work effectively 
even when it is connected to a 
HUB that has a spanning tree 
feature. However, printer start 
up time gets longer when 
computers are connected with 
two or three small LANs.
When Small is selected, 
computers can cover from two 
or three small LANs to a large 
LAN, but may not work 
effectively when the network is 
connected to a HUB with a 
spanning tree feature.
Hub Link 
SettingAuto 
Negotiate
100Base-TX 
Full
100Base-TX 
Half
10Base-T Full
10Base-T Half
Sets a method to link to a HUB. 
When Auto is set, a connection 
method to a HUB is selected 
automatically.
Factory 
Defaults?ExecuteSpecifies whether to initialize 
the network factory default 
settings for the Network.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							36 – C710n User’s Guide
Print 
SetupPersonalit
yAuto
PostScript
PCL
IBM PPR
EPSON FX
Selects a printer language.
Copies1- 999Selects the default number of 
copies.
DuplexOn/OffSpecifies Duplex print (option) 
if a Duplex unit is installed and 
enabled
BindingLong Edge
Short Edge
Specifies Binding in duplex 
printing (if a Duplex unit is 
installed and enabled)
Media 
CheckEnable
Disable
Sets whether the printer checks 
the matching of printed data 
size and that of the tray. Only 
standard sizes are checked.
Resolution600dpi
600x1200dpi
600dpi multi-
level.
Sets default resolution.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							37 – C710n User’s Guide
Print 
Setup 
(cont.)To n e r  
Save
 
Mode
On/OffThis function works effectively 
only if the data input is color 
RGB data. This setting is valid 
in PS and PCL, but does not 
take effect in the following 
cases.
(1) PS: If Color Matching is set 
OFF.
(2) PS: If any setting other 
than ASIC Color Matching is 
set.
(3) PS: CMYK data when Ink 
Simulation Mode is used (valid 
in any other cases except Case 
(1) and Case (2) above as long 
as data is RGB).
(4) PCL binary data (Color/
Monochrome).
Mono-
Print
 
Speed
Auto
Color Speed
Normal Speed
High Quality
Sets the monochrome print 
speed. Prints at the most 
appropriate speed for page 
process if Auto is set.
Prints always at the color print 
speed if Color is set.
Prints always at the 
monochrome print speed if 
Normal is set.
Prints always at 26ppm of the 
gradation print speed for both 
color and monochrome print if 
High Quality is set.
Default 
Orientatio
n
Portrait
Landscape
Specifies print orientation.
Not valid for PS (valid only for 
PCL/ IBMPPR/EPSONFX/ HP-
GL2).
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							38 – C710n User’s Guide
Print 
Setup 
(cont.)Form 
Length5 lines
~
60 lines
~
128 lines
Sets the number of lines that 
can be printed on a page
Not valid for PS (valid only for 
PCL/HP-GL2).
Default values listed to the left 
are for Letter/A4. In practice, 
however, they change according 
to the size of paper loaded in 
the tray.
Edit SizeCassette 
Size/
Letter/
Executive/
Legal14/
Legal13.5/
Legal13/A4/
A5/A6/B5/
Custom/C5/
Com-10 
Envelope/
Monarch 
Envelope/DL 
Envelope/C5/
Com-9 
Envelope
Sets the size of an area to draw 
when the host PC does not 
specify the size via the paper 
edit size designating command 
(Not valid for PS - only for PCL).
TrappingOff
Narrow
Wide
Trapping, or spreading and 
choking, is a prepress 
technique consisting of creating 
small overlaps between 
abutting colors in order to mask 
registration issues in the 
graphical production.
Trapping X 
Width0 pixels
~
4 pixels
Sets the horizontal dimension 
of the trapping area.
Trapping Y 
Width0 pixels
~
4 pixels
Sets the vertical dimension of 
the trapping area.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							39 – C710n User’s Guide
Print 
Setup 
(cont.)
PS Setup
X 
Dimension64 mm
~
210 mm
~
216 mm
Specifies paper width of 
Custom paper as a default 
value.
Sets a paper size at right angles 
to the paper run direction.
Y 
Dimension127 mm
~
297 mm
~
1220 mm
Specifies paper length of 
Custom paper as a default 
value.
Sets a paper size in the same 
direction as the paper run 
direction.
Network 
Protocol
ASCII/RAWSpecifies PS communication 
protocol mode of data from NIC 
port.
(In RAW mode, Ctrl-T is 
invalid). PS models only.
Parallel 
Protocol
ASCII/RAWSpecifies PS communication 
protocol mode of data from 
Centronics port.
(In RAW mode, Ctrl-T is 
invalid). PS models only.
USB 
Protocol
ASCII/RAWSpecifies PS communication 
protocol mode of data from USB 
port.
(In RAW mode, Ctrl-T is 
invalid). PS models only.
PCL 
SetupFont 
SourceResidentSpecifies the location of PCL 
default font.
Font 
NumberI0 ~ I90Sets the PCL font number.
The valid range of this variable 
changes depending on the 
FONT SOURCE setting at the 
time. If the default font is set 
for FONT SOURCE, the number 
starts at 0. If it is not, the 
number starts at 1. The 
maximum value is equal to the 
number of fonts installed in 
FONT SOURCE.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							40 – C710n User’s Guide
PCL 
Setup 
(cont.)Font Pitch99.9 CPI
~
10.00 CPI
~
0.44 CPI
Width of the PCL default font in 
characters per inch (CPI). 
Default font is fixed-pitch, 
scalable font.
The value of pitch is displayed 
down to the second decimal 
place.
Displayed only when the font 
selected in Font No. is a fixed-
spacing, scalable font.
Symbol 
SetPC-8Sets the symbol set of PCL (see 
machine operator panel for 
complete list).
A4 Print 
Width78 column
80 column
Sets the number of characters 
for A4 paper.
Auto LF.
This is for 10-CPI characters 
when Auto CR/LF Mode is set to 
OFF.
This menu is enabled only when 
A4 paper is selected in the 
menu that sets the print width 
of A4 paper in portrait 
orientation.
Usually, such A4 paper print 
width is set slightly narrower 
than 8 inches (about 7.93 
inches).
This setting cannot print 80 10-
cpi characters (only prints up to 
78 10-cpi characters). 80 
characters set at A4 Print Width 
widen the right and left 
margins.
A PCL command selects or 
selects/deselects Auto CR/LF 
mode.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals