OKI C710cdtn User Manual

31 – C710n User’s Guide
System 
Adjust Power Save Time 
Default: 5
Select from 5/10/15/30/60 
Minutes. Select by scroll and Enter 
button.
Clearable 
Warning
Default: ONLINE
Select from: ONLINE/Job. Select by 
scroll and Enter button. PS job only.
Auto Continue
Default: Off
Select from On/Off. Select by scroll 
and Enter button.
Manual Timeout 
Default: 60
Select fro  Off/30 seconds/60 
seconds.
Select by scroll and Enter button.
Wait Timeout
Default: 40
Select from Off/5/10/20/30/40/...

32 – C710n User’s Guide
System 
Adjust
 
(cont.)
Paper Black 
Settings -2/-1/0/
+1/+2
Default: 0
Used for fine adjustment of the black 
print on paper.
Paper color 
Settings-2/-1/0/
+1/+2
Default: 0
Used for fine adjustment of the color 
print on paper.
Trans. Black 
Settings -2/-1/0/
+1/+2
Default: 0
Used for fine adjustment of the black 
print on transparencies.
Trans. color 
Settings -2/-1/0/
+1/+2
 
Default: 0
Used for fine adjustment of the color 
print on transparencies.
SMR Setting +3/
+2/+1/-...

33 – C710n User’s Guide
Shutdown menu
This menu only appears if the hard disk drive is installed.
This item should always be selected before switching the printer 
off, to ensure that no hard disk data is lost.
Admin Setup
ITEMSETTINGSEXPLANATION
Shutdown 
StartExecute Performs controlled shutdown of the printer, 
ensuring that all files on the internal hard 
disk are closed before power is turned off. 
Only power the printer off when the display 
indicates that shutdown is complete....

34 – C710n User’s Guide
Network 
Setup 
(cont.)NetWareEnable
Disable
Sets Enable/Disable of NetWare 
Protocol.
EtherTalkEnable
Disable
Sets Enable/Disable of 
EtherTalk Protocol.
Frame 
Ty p eAuto
802.2
802.3
Ethernet II
SNAP
Sets the frame type.
Netware should be enabled.
Ty p e I P  
Address 
SetAuto
Manual
Sets the IP Address setting 
method.
TCP/IP should be enabled.
IP Addressxxx.xxx.xxx.xx
xSets the IP Address.
TCP/IP should be enabled.
Subnet 
Maskxxx.xxx.xxx.xx
xSets the Subnet Mask.
TCP/IP...

35 – C710n User’s Guide
Network 
Setup 
(cont.)FTPEnable
Disable
Sets Enable/Disable of FTP.
Enable: FTP is available. 
Disable: FTP is not available. 
TCP/IP should be enabled.
SNMPEnable
Disable
Sets Enable/Disable of SNMP.
Enable: SNMP is available. 
Disable: SNMP is not available. 
TCP/IP or NetWare should be 
enabled.
Network 
ScaleNormal
Small
When Normal is selected, the 
network can work effectively 
even when it is connected to a 
HUB that has a spanning tree 
feature. However, printer start 
up...

36 – C710n User’s Guide
Print 
SetupPersonalit
yAuto
PostScript
PCL
IBM PPR
EPSON FX
Selects a printer language.
Copies1- 999Selects the default number of 
copies.
DuplexOn/OffSpecifies Duplex print (option) 
if a Duplex unit is installed and 
enabled
BindingLong Edge
Short Edge
Specifies Binding in duplex 
printing (if a Duplex unit is 
installed and enabled)
Media 
CheckEnable
Disable
Sets whether the printer checks 
the matching of printed data 
size and that of the tray. Only 
standard sizes are...

37 – C710n User’s Guide
Print 
Setup 
(cont.)To n e r  
Save
 
Mode
On/OffThis function works effectively 
only if the data input is color 
RGB data. This setting is valid 
in PS and PCL, but does not 
take effect in the following 
cases.
(1) PS: If Color Matching is set 
OFF.
(2) PS: If any setting other 
than ASIC Color Matching is 
set.
(3) PS: CMYK data when Ink 
Simulation Mode is used (valid 
in any other cases except Case 
(1) and Case (2) above as long 
as data is RGB).
(4) PCL binary data...

38 – C710n User’s Guide
Print 
Setup 
(cont.)Form 
Length5 lines
~
60 lines
~
128 lines
Sets the number of lines that 
can be printed on a page
Not valid for PS (valid only for 
PCL/HP-GL2).
Default values listed to the left 
are for Letter/A4. In practice, 
however, they change according 
to the size of paper loaded in 
the tray.
Edit SizeCassette 
Size/
Letter/
Executive/
Legal14/
Legal13.5/
Legal13/A4/
A5/A6/B5/
Custom/C5/
Com-10 
Envelope/
Monarch 
Envelope/DL 
Envelope/C5/
Com-9 
Envelope
Sets the...

39 – C710n User’s Guide
Print 
Setup 
(cont.)
PS Setup
X 
Dimension64 mm
~
210 mm
~
216 mm
Specifies paper width of 
Custom paper as a default 
value.
Sets a paper size at right angles 
to the paper run direction.
Y 
Dimension127 mm
~
297 mm
~
1220 mm
Specifies paper length of 
Custom paper as a default 
value.
Sets a paper size in the same 
direction as the paper run 
direction.
Network 
Protocol
ASCII/RAWSpecifies PS communication 
protocol mode of data from NIC 
port.
(In RAW mode, Ctrl-T is...

40 – C710n User’s Guide
PCL 
Setup 
(cont.)Font Pitch99.9 CPI
~
10.00 CPI
~
0.44 CPI
Width of the PCL default font in 
characters per inch (CPI). 
Default font is fixed-pitch, 
scalable font.
The value of pitch is displayed 
down to the second decimal 
place.
Displayed only when the font 
selected in Font No. is a fixed-
spacing, scalable font.
Symbol 
SetPC-8Sets the symbol set of PCL (see 
machine operator panel for 
complete list).
A4 Print 
Width78 column
80 column
Sets the number of characters 
for...