OKI C610n User Manual

							
41 – C610/C711 User’s Guide
Print 
Setup
(cont.)
To n e r  S a v e 
Mode
On/OffThis function works effectively 
only if the data input is color RGB 
data. This setting is valid in PS 
and PCL, but does not take effect 
in the following cases.
(1) PS: If Color Matching is set 
OFF.
(2) PS: If any setting other than 
ASIC Color Matching is set.
(3) PS: CMYK data when Ink 
Simulation Mode is used (valid in 
any other cases except Case (1) 
and Case (2) above as long as 
data is RGB).
(4) PCL binary data (Color/
Monochrome).
Mono-Print 
Speed
Auto
Color Speed
Normal Speed
Sets the monochrome print 
speed. Prints at the most 
appropriate speed for page 
process if  Auto is set.
Prints always at the color print 
speed if  Color is set.
Prints always at the monochrome 
print speed if  Normal is set.
Default 
Orientation
Portrait
Landscape
Specifies print orientation.
Not valid for PS (valid only for 
PCL/ IBMPPR/EPSONFX/ HP-
GL2).
Form 
Length5 lines
~
64 lines
~
128 lines
Sets the number of lines that can 
be printed on a page
Not valid for PS (valid only for 
PCL/HP-GL2).
Default values listed to the left 
are for Letter/A4. In practice, 
however, they change according 
to the size of paper loaded in the 
tray.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
42 – C610/C711 User’s Guide
Print 
Setup
(cont.)
Edit SizeCassette Size/
A4/A5/A6/B5/
Legal14/
Legal13.5/
Legal13/Letter/
Executive/
Custom/Com-9 
Envelope/Com-
10 Envelope/
Monarch 
Envelope/DL 
Envelope/C5/
Index Card
Sets the size of an area to draw 
when the host PC does not 
specify the size via the paper 
edit size designating command 
(Not valid for PS — only for PCL).
TrappingOff
Narrow
Wide
Sets trapping.
X 
Dimension64 mm
~
210 mm
~
216 mm
Specifies paper width of Custom 
paper as a default value.
Sets a paper size at right angles 
to the paper run direction.
Y 
Dimension127 mm
~
297 mm
~
1321 mm
Specifies paper length of Custom 
paper as a default value.
Sets a paper size in the same 
direction as the paper run 
direction.
PS SetupNetwork 
Protocol
ASCII/RAWSpecifies PS communication 
protocol mode of data from NIC 
port.
(In RAW mode, Ctrl-T is invalid). 
PS models only.
Parallel 
Protocol*
ASCII/RAWSpecifies PS communication 
protocol mode of data from 
Centronics port.
(In RAW mode, Ctrl-T is invalid). 
PS models only.
* This menu item is applicable to the 
C711 only.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
43 – C610/C711 User’s Guide
PS Setup
(cont.)
USB 
Protocol
ASCII/RAWSpecifies PS communication 
protocol mode of data from USB 
port.
(In RAW mode, Ctrl-T is invalid). 
PS models only.
PCL SetupFont SourceResidentSpecifies the location of PCL 
default font.
Font 
NumberI0 ~ I90Sets the PCL font number.
The valid range of this variable 
changes depending on the FONT 
SOURCE setting at the time. If 
the default font is set for FONT 
SOURCE, the number starts at 0. 
If it is not, the number starts at 
1. The maximum value is equal 
to the number of fonts installed 
in FONT SOURCE.
Font Pitch0.44 CPI
~
10.00 CPI
~
99.99 CPI
Width of the PCL default font in 
characters per inch (CPI). 
Default font is fixed-pitch, 
scalable font.
The value of pitch is displayed 
down to the second decimal 
place.
Displayed only when the font 
selected in Font No. is a fixed-
spacing, scalable font.
Font Height4.00 point
~
12.00 point
~
999.75 point
Height of the PCL default font. 
The value is displayed down to 
the second decimal place (in 
0.25 point increments).
Displayed only when the font 
selected in Font Number is a 
proportional-spacing, scalable 
font.
Symbol SetPC-8Sets the symbol set of PCL (see 
machine operator panel for 
complete list).
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
44 – C610/C711 User’s Guide
PCL Setup
(cont.)
A4 Print 
Width78 column
80 column
Sets the number of characters 
for A4 paper.
Auto LF.
This is for 10-CPI characters 
when Auto CR/LF Mode is set to 
OFF.
This menu is enabled only when 
A4 paper is selected in the menu 
that sets the print width of A4 
paper in portrait orientation.
Usually, such A4 paper print 
width is set slightly narrower 
than 8 inches (about 7.93 
inches).
This setting cannot print 80 10-
cpi characters (only prints up to 
78 10-cpi characters). 80 
characters set at A4 Print Width 
widen the right and left margins.
A PCL command selects or 
selects/deselects Auto CR/LF 
mode.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
45 – C610/C711 User’s Guide
PCL Setup
(cont.)
White Page 
SkipOn/OffSets whether to eject a page 
without any data to print (blank 
page) upon reception of FF 
command (OCH) in PCL Mode.
OFF: Ejecting.
CR FunctionCR/CR+LFSets action when CR code is 
received in PCL.
CR: Carriage Return 
CR+LF: Carriage Return and Line 
Feed
LF FunctionLF/ LF+CRSets action when LF code is 
received in PCL.
LF: Line Feed 
LF+CR: Line Feed and Carriage 
Return
Print MarginNormal
1/5 inch
1/6 inch
Sets a non-printable area of 
paper.
The width of the area along the 
right and left sides of paper (left 
and right sides depend on paper 
orientation).
NORMAL: PCL emulation 
compatible, approximately 1/
4~1/4.3INCH (depending on 
paper) is outside the printable 
area.
Tr u e 
Black
On/OffSets whether to use Composite 
Black (CMYK mixed) or Pure 
Black (K only) for the black 
(100%) in image data.
OFF: Mode using Composite 
Black
ON: Mode using Pure Black
(PCL only)
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
46 – C610/C711 User’s Guide
PCL Setup 
(cont.)
Pen Width 
Adjust
On/OffWhen minimum width is 
specified in PCL, sometimes a 1-
dot line, looks broken.
With PEN WIDTH Adjust set to 
ON, when the minimum width is 
specified, the line width will be 
emphasized so as to look wider 
than a 1-dot line.
With PEN WIDTH Adjust set to 
OFF, the line will appear as 
before.
Tr a y  I D  #
Tr a y  2  1 ~  5 ~ 59Sets the # to specify Tray 2 for 
the paper feed destination 
command (ESC&l#H) in PCL5e 
emulation.
(Displayed only if Tray 2 is 
installed).
Tr a y  3  1 ~  20 ~ 59Sets the # to specify Tray 3 for 
the paper feed destination 
command (ESC&l#H) in PCL5e 
emulation.
(Displayed only if Tray 3 is 
installed).
MPTray1 ~  4 ~ 59Sets the # to specify the MP tray 
for the paper feed destination 
command (ESC&l#H) in PCL5e 
emulation.
IBM PPR 
SetupCharacter 
Pitch10 CPI
12 CPI
17 CPI
20 CPI
Proportional
Specifies character pitch in IBM 
PPR emulation.
Font 
Condense12CPI to 
20CPI
12CPI to 12CPI
Specifies 12CPI pitch for 
Condense Mode.
Character 
SetSET-2
SET-1
Sets a character set.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
47 – C610/C711 User’s Guide
IBM PPR 
Setup
(cont.)
Symbol SetIBM 437Sets the Symbol Set for IBM PPR 
(see machine operator panel for 
complete list).
Letter O 
StyleEnable/DisableSpecifies the style that replaces 
ø (9B) and ¥ (9D) with ø (ou) 
and Ø (zero).
Zero 
CharacterNormal /
SlashedSpecifies the style of 0(zero). 
SLASHED: SLASH ZERO
Line Pitch6 /8 LPISets line space.
White Page 
SkipOn/ OffSets whether to eject a blank 
sheet. Available only when 
simplex is set.
CR FunctionCR/CR+LFSets action when CR code is 
received.
LF FunctionLF/LF+CRSets action when LF code is 
received.
Line Length80 /136 columnSpecifies the number of 
characters per line.
Form 
Length11/11.7/12 inchSpecifies the length of paper.
TOF 
Position0.0 /0.1/~1.0 
inchSets the position from the top 
edge of paper.
Left Margin0.0 /0.1/~1.0 
inchSets the amount to shift the 
horizontal print start position to 
the right.
Fit to LetterEnable/ DisableSets the printing mode that can 
fit print data, equivalent to 11 
inches (66 lines), in the LETTER-
size printable area.
Te x t  H e i g h tSame/DiffSets height of a character.
SAME: Regardless of CPI, same 
height
DIFF: According to CPI, character 
heights vary.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
48 – C610/C711 User’s Guide
EPSON FX 
SetupCharacter 
Pitch10 CPI/12 CPI/
17 CPI
20 CPI/
Proportional
Specifies character pitch in 
Epson FX emulation.
Character 
SetSET-2
SET-1
Sets a character set.
Symbol SetIBM 437Sets the Symbol Set for Epson 
FX Emulation.
(see machine operator panel for 
complete list).
Letter O 
StyleEnable/ DisableSpecifies the style that replaces 
ø (9B) and ¥ (9D) with ø (ou) 
and Ø (zero).
Zero 
CharacterNormal /
SlashedSpecifies the style of 0(zero). 
SLASHED: SLASH ZERO
Line Pitch6 /8 LPISets line space.
White Page 
SkipOn/ OffSets whether to eject a blank 
sheet. Available only when 
simplex is set.
CR FunctionCR/CR+LFSets action when CR code is 
received.
Line Length80/136 ColumnSpecifies the number of 
characters per line.
Form 
Length11/11.7/12 inchSpecifies the length of paper.
TOF 
Position0.0 /0.1/~1.0 
inchSets the position from the top 
edge of paper.
Left Margin0.0 /0.1/~1.0 
inchSets the amount to shift the 
horizontal print start position to 
the right.
Fit to LetterEnable/ DisableSets the printing mode that can 
fit print data, equivalent to 11 
inches (66 lines), in the LETTER-
size printable area.
Te x t  H e i g h tSame/DiffSets height of a character.
SAME: Regardless of CPI, same 
height; DIFF: According to CPI, 
character heights vary.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
49 – C610/C711 User’s Guide
Color 
SetupInk 
Simulation
Off
SWOP
Euroscale
Japan
The machine has its own process 
simulation engine which 
simulates standard colors in the 
printer.
This function is available only 
with PS language jobs.
UCRLow
Medium
High
Selects limitation to the toner 
layer thickness.
If paper curl occurs in dark 
printing, selecting MEDIUM or 
LIGHT sometimes helps reduce 
this curl.
UCR = Under Color Removal.
CMY 100%
Density
Enable/DisableEnable/Disable 100% output 
against the CMY100% TRC 
compensation. Ordinarily, the 
TRC compensation function holds 
control for the appropriate print 
density; thus 100% output is not 
always possible.
Selecting ENABLE will enable 
100% output in any individual 
color. The actual print, including 
the TRC compensation function is 
limited to an appropriate area. 
This function is for special 
purposes such as specification in 
CMYK color reduction in PS.
CMYK 
Conversion
On/OffSetting to “OFF” will simplify the 
conversion process of CMYK 
data, which will reduce the 
processing time.
This setting is ignored when Ink 
Simulation function is used.
PS only
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							
50 – C610/C711 User’s Guide
Memory 
SetupReceive 
Buffer Size
Auto
0.5 megabyte
1 megabyte
2 megabyte
4 megabyte
8 megabyte
16 megabyte
32 megabyte
Sets the size of receive buffer
Resource 
Save
Auto
Off
0.5 megabyte
1 megabyte
2 megabyte
4 megabyte
8 megabyte
16 megabyte
32 megabyte
Sets the size of resource saving 
area.
Flash 
Memory 
SetupInitializeExecuteInitializes Resident FLASH.
When the Enter button is 
pressed, the following 
confirmation message appears.
  Are You Sure?          Yes/No
If  No  is selected, the previous 
menu display resumes. 
If  Yes  is selected, the following 
confirmation message displays.
 Execute Now?         Yes/No
If  No  is selected, the previous 
menu display resumes. At this 
time, the request to execute 
FLASH initialization is put into 
the memory and initialization will 
be executed at power cycle.
If  Yes  is selected, shutdown 
takes place, and FLASH is 
initialized at power Off/On cycle.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals