OKI C6100hdn User Manual

  
 
Okidata C6100 Setup & User Guide 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals 

 1
 
Table of Contents -  
 
STEP 1- UNPACK/PREPARE PRINTER………………………………………………………………………………………2 
STEP 2 – PRINT DEMO PAGE.………..……………….…..............................................................................................4 
STEP 3 - INSTALL HANDY REFERENCE GUIDE ...................................................................................................4  
STEP 4 - DISCONNECT CURRENT PRINTER ………………….................................................................................5 
STEP 5 -...

 2
Step 1 – Unpack / Prepare Printer    
1.  Designate an area for your new printer to be installed.  
2.  Ask someone to assist in lifting the printer out of the box.  
 
3.  Lift the printer out of the box (straight up).  
4.  Remove all pieces of tape from the printer. (11 sheets with tape) (6 single pieces of tape)  
5.  Follow the instructions below to remove tape from the inside of the printer: 
 
 
•  Press the release button and lift the top cover.   
•  On the right-hand side of each drum/toner...

 3 
• Reinstall the black drum/toner unit.   
• Repeat these steps for all remaining drum/toner units.   
Important! If TONER SENSOR ERROR appears when you turn on the printer, the lever for 
the toner cartridge color indicated is not pushed all the way back. 
 
 
6.  Follow the steps below to prepare the fuser: 
 
remove orange piece 
•  Press firmly on the blue lock (1) to release the orange transport restraint (2). Pull the restraint out by 
moving it left and then pulling up. This piece looks as...

 4  
•  Load the paper (maximum 300 sheets 20-lb [75 g/m2] paper).   
•  Make sure the paper guides are snug against the paper and are locked in place. 
 
  
Note: Do not fill above paper full indicator (A).  
•  Gently close the paper tray.  
8.  Insert the power cable (1: Be sure to use only the power cable supplied with your printer!), then 
plug it directly into a grounded wall outlet and turn on the printer
.  
9.  Do not connect any other cables at this time. 
 
 
Step 2 – Print Demo Page 
  
1....

 5
Step 4 – Disconnect Current Printer (If one exists)  
1.  Press the power button to turn off the printer.  
2.  Disconnect the power cable from the power outlet and from the printer.  
 
Step 5 - Connect New Printer / Load Software  
For this portion, refer to the diagram provided on page 20.  (Diagram – Rear View)   
•  Place the printer in its designated area.  
•  Connect the power cord to a power outlet. When possible, connect the (C6100) power cord to a 
dedicated power outlet.
  
 
NOTE: It is...

 6
6.  Next, if you agree, accept the License Agreement:   
   
The Installer screen will appear:  
 
7. Click Install Driver.   
   
 
 
 
 
 
 
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals 

 7  
8. Select Network printer and click Next: 
 
  
9.  Use the mouse to select ‘Directly to the network using TCP/IP’.  Click Next.  
 
 
 
 
 
 
 
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals 

 8
10. If you know the IP address for the printer, use the mouse to select IP address and enter the number.  If 
you do not know the IP address for your printer, click Next to browse for it.  
 
 
 
 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals 

 9
11. Click the Back button to get to the IP address entry screen: 
 
  
12. Enter the IP address and click Next.  Note – use the tab key to enter IP address.  
 
  
13. Use the mouse to click PCL, and then click Next.  
 
 
 
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals