OKI C5900DTN User Manual

							Menu functions> 131
TRUE BLACKOFF / ONSelects whether black image data 
is printed using black toner (ON) 
or 100% CMY (OFF). (Valid in PCL 
emulation mode only.)
PEN WIDTH 
ADJUST
Tr a y  I D #
MP TRAY4
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 132
PPR EMULATION
This menu controls settings effective when the printer is 
operating in PPR emulation mode.
ITEMSETTINGSEXPLANATION
CHARACTER 
PITCH10 CPI; 12 CPI; 17 
CPI; 20 CPI; 
PROPORTIONALSpecifies character pitch in IBM 
PPR emulation.
FONT 
CONDENSE12CPI - 20CPI; 
12CPI - 12CPISpecifies 12CPI pitch for Condense 
Mode.
CHARACTER 
SETSet 1; Set 2Specifies a character set.
SYMBOL SETIBM 437Specifies a symbol set.
LETTER 0 
STYLEDisable; Enable Specifies the style that replaces 
9BH with letter o and 9DH with a 
zero
ZERO 
CHARACTERNormal; SlashedSets the zero to be slashed or 
unslashed.
LINE PITCH 6 LPI; 8 LPI Specifies the line spacing.
WHITE PAGE 
SKIPOFF / ONSelects whether blank pages are 
printed or not.
CR FUNCTIONCR / CR+LF Selects whether a received 
carriage return character (0Dh) 
also causes a line feed.
LF FUNCTIONLF / LF+CRSelects whether a received line 
feed character (0Ah) also causes a 
carriage return.
LINE LENGTH80 COLUMN; 136 
COLUMNSpecifies the number of characters 
per line.
FORM 
LENGTH11 Inch; 11.7 Inch
12 InchSpecifies the length of paper.
TOF 
POSITION0.0 INCH - 1.0 
InchSpecifies the distance of print from 
the top edge of the paper.
LEFT MARGIN0.0 Inch - 1.0 InchSpecifies the distance of print from 
the left hand edge of the paper.
FIT TO 
LETTERDisable; Enable Sets the printing mode that can fit 
print data, equivalent to 11 inches 
(66 lines), in the LETTER-size 
printable area.
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 133
TEXT HEIGHTSame; DiffSets the height of a character.
SAME: Regardless of CPI, same 
height
DIFF: As CPI, character heights 
vary.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 134
FX EMULATION
This menu controls settings effective when the printer is 
operating in FX emulation mode.
ITEMSETTINGSEXPLANATION
CHARACTER 
PITCH10 CPI; 12 CPI; 17 
CPI; 20 CPI; 
PROPORTIONALSpecifies character pitch in this 
emulation.
CHARACTER 
SETSet 1; Set 2Specifies a character set.
SYMBOL SET IBM 437 Specifies a symbol set.
LETTER 0 
STYLEDisable; EnableSpecifies the style that replaces 
9BH with letter o and 9DH with a 
zero
ZERO 
CHARACTERNormal; Slashed Sets the zero to be slashed or 
unslashed.
LINE PITCH6 LPI; 8 LPISpecifies the line spacing.
WHITE PAGE 
SKIPOFF / ON Selects whether blank pages are 
printed or not.
CR FUNCTIONCR / CR+LFSelects whether a received 
carriage return character (0Dh) 
also causes a line feed.
LINE LENGTH80 COLUMN; 136 
COLUMNSpecifies the number of characters 
per line.
FORM 
LENGTH11 inch; 11.7 inch;
12 inchSpecifies the length of paper.
TOF 
POSITION0.0 inch  -  1.0  inch Specifies the distance of print from 
the top edge of the paper.
LEFT MARGIN0.0 inch - 1.0 inchSpecifies the distance of print from 
the left hand edge of the paper.
FIT TO 
LETTERDisable; Enable Sets the printing mode that can fit 
print data, equivalent to 11 inches 
(66 lines), in the LETTER-size 
printable area.
TEXT HEIGHTSame; DiffSets the height of a character.
SAME: Regardless of CPI, same 
height.
DIFF: As CPI, character heights 
vary.
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 135
USB MENU
This menu controls the operation of the printer’s USB data 
interface.
NETWORK MENU
This menu controls the operation of the printer’s 10Base-T/
100Base-TX network interface.
ITEMSETTINGSEXPLANATION
SOFT RESET ENABLE / 
DISABLEEnables or disables the SOFT RESET 
command.
SERIAL NUMBERENABLE / 
DISABLE
OFFLINE 
RECEIVEENABLE / 
DISABLE
SPEED12 / 480 MpsSelects the interface speed
ITEMSETTINGSEXPLANATION
TCP/IPENABLE / 
DISABLEEnables or disables this network 
protocol.
IP VERSIONIP V4 / IPV 4 & 
V6
NETBEUIENABLE / 
DISABLEEnables or disables this network 
protocol.
NETWAREENABLE / 
DISABLEEnables or disables this network 
protocol.
ETHERTALKENABLE / 
DISABLEEnables or disables this network 
protocol.
FRAME TYPEAUTO / 802.2 / 
802.3 / 
ETHERNET II / 
SNAPSelects the Ethernet MAC layer 
frame type.
IP ADDRESS 
SETAUTO / MANUAL Specifies whether IP address 
allocation is automatic (DHCP) or 
manually assigned.
IP ADDRESSxxx.xxx.xxx.xxxCurrent assigned IP address. To 
change, press ENTER and use 
+/– 
keys to increment 1st octet, then 
press ENTER again to move on to 
next octet. When 4th octet has been 
set, press ENTER again to register 
new address.
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 136
MAINTENANCE MENU
This menu provides access to various printer maintenance 
functions.
SUBNET MASK xxx.xxx.xxx.xxx Current assigned subnet mask. To 
change, proceed as above.
GATEWAY 
ADDRESSxxx.xxx.xxx.xxxCurrent assigned gateway address. 
To change, proceed as above.
FAC TO RY 
DEFAULTSEXECUTE Reloads the settings present when 
the unit was setup by the 
manufacturer.
WEBENABLE / 
DISABLEEnables or disables Web config. 
facility.
TELNET ENABLE / 
DISABLEEnables or disables Telnet config. 
facility.
FTPENABLE / 
DISABLEEnables or disables communication 
via FTP.
SNMPENABLE / 
DISABLEEnables or disables SNMP protocol.
NETWORK 
SCALENORMAL / 
SMALLSelects network size.
HUB LINK 
SETTINGAUTO 
NEGOTIATE
100BASE-TX 
FULL
100BASE-TX 
HALF
10BASE-T FULL
10BASE-T HALFSets full or half duplex for 
communication via a network hub.
ITEMSETTINGSEXPLANATION
ITEMSETTINGSEXPLANATION
MENU RESET EXECUTE Resets menus to default settings.
SAVE MENUEXECUTESaves current menu settings as 
default values. At confirmation 
prompt, press ENTER to confirm 
save, or CANCEL to cancel.
POWER SAVEENABLE / 
DISABLEEnables or disables automatic power 
save mode. Delay before entering 
this mode is set in the system 
configuration menu.
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 137
USAGE MENU
This menu is for information only, and provides an indication of 
total usage of the printer and the expected life left in its 
consumable items. This is particularly useful if you do not have a 
full set of replacement consumables to hand and you need to 
know how soon you will need them.
PAPER BLACK 
SETTING–2~0~+2Used for small adjustment when you 
experience faded print or light 
specks / streaking in monochrome 
printing on white paper. Select a 
higher value to reduce fading, or a 
lower value to reduce specks or 
streaking in high density print areas.
PAPER COLOR 
SETTING–2~0~+2 As above, but for colour printing.
TRANSPR 
BLACK SETTING–2~0~+2As above but for mono printing on 
transparencies.
TRANSPR 
COLOR SETTING–2~0~+2 As above but for colour printing on 
transparencies.
ITEMSETTINGSEXPLANATION
ITEMEXPLANATION
TRAYn PAGE COUNT The total number of pages fed from tray n.
MPT PAGE COUNTThe total number of pages fed from the multi 
purpose tray.
COLOUR PAGE 
COUNTThe total number of pages printed in colour.
MONO PAGE COUNTThe total number of pages printed in 
monochrome.
K DRUM LIFE 
REMAINING
C DRUM LIFE 
REMAINING
M DRUM LIFE 
REMAINING
Y DRUM LIFE 
REMAININGPercentage of life remaining in these consumable 
items.
BELT LIFE 
REMAININGPercentage of belt life remaining.
FUSER LIFE 
REMAININGPercentage of fuser life remaining.
Downloaded From ManualsPrinter.com Manuals 
						

							Menu functions> 138
JOB LOG MENU
K TONER
C TONER
M TONER
Y TONER
Cartridge size and current toner level.
ITEMSETTINGEXPLANATION
JOB LOG ENABLE/
DISABLEPrints a list of jobs carried out 
on this printer.
ITEMEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							Overlays and Macros (Windows only)> 139
OVERLAYS AND MACROS (WINDOWS ONLY)
WHAT ARE OVERLAYS AND MACROS?
If you would like to print on special stationery, such as forms and 
letterhead, but do not want to use pre-printed stationery, you 
can create your own using these advanced features.
You can use PostScript overlays to generate all your special 
stationery and store it in the printer for use whenever you need 
it. If you have chosen to install the PCL driver, macros perform a 
similar function.
You can create several overlays or macros, and combine them in 
any way you like to produce a variety of forms and other special 
stationery. Each image can be printed on just the first page of a 
document, on all pages, on alternate pages, or just the pages 
that you specify.
NOTE:
PostScript overlays are not available for Windows 95/98/Me.
Downloaded From ManualsPrinter.com Manuals 
						

							Overlays and Macros (Windows only)> 140
CREATING POSTSCRIPT OVERLAYS
Three steps are required to create an overlay:
1.Create the form data using your own application software 
and print it to a printer (.PRN) file.
2.Use the Storage Device Manager utility software supplied 
on CD with your printer to create a “project file,” import 
the.PRN file(s), and download the generated filter (.HST) 
file to the printer. The project file will contain one or more 
overlay images which are functionally related, such as the 
cover page and the continuation page images for business 
letters.
3.Use downloaded files to define your overlays ready for use 
when printing your documents.
When printing overlay files to disk, do not select any special 
features, such as two-sided printing or multiple copies. These are 
not appropriate to overlays, they apply only to your final 
documents.
CREATING THE OVERLAY IMAGE
1.Use your preferred application, perhaps a graphics 
program, to create the required overlay image and save 
it.
2.Open your 
application’s Print… 
dialogue.
3.Make sure that the 
selected printer 
name (1) is that of 
your PostScript 
printer driver.
4.Select the Print To 
File(2) option.
5.Click the Properties button (3) to open the Document 
Properties window.
13
2
Downloaded From ManualsPrinter.com Manuals