OKI C110 User Manual

							51  -  C110 User’s Guide
10Align the shaft on each end of 
the toner cartridge with its 
holders, and then insert the 
cartridge.
NoteBefore inserting the toner 
cartridge, make sure that 
the color of the toner 
cartridge to be installed is 
the same as the label on 
the toner cartridge 
carousel.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Important!
Do not touch the contact 
indicated in the illustration.
 
 
 
 
 
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals 
						

							52  -  C110 User’s Guide
11Press in the toner cartridge until 
it locks into place.
12Close the front cover.
NoteTo replace the toner 
cartridge for another 
color, after the front cover 
has been closed, check 
that the indicator for the 
toner to be replaced is lit 
(if necessary, press the 
Rotate Toner key), and 
then replace the toner 
cartridge as described in 
steps 3 through 11.
 
13Press the Cancel key to reset the printer and clear the indicator message.
NoteThe printer must complete a calibration cycle (less than 2 minutes) 
after a toner cartridge has been replaced. If you open the top or 
front cover before the printer is reset, the calibration stops, then 
starts over again after the cover is closed.
Replacing All Toner Cartridges at the Same Time
CAUTION
Be careful not to spill toner while replacing a toner cartridge. If 
toner spills, immediately wipe it off with a soft, dry cloth.
Downloaded From ManualsPrinter.com Manuals 
						

							53  -  C110 User’s Guide
By using the Eject All Toner mode, all toner cartridges can be replaced at the 
same time.
1Use either operation described below to switch the printer to Eject All 
Toner mode.
!Hold down the Rotate Toner key for more than 10 seconds.
!On the Panel tab of the Remote Panel Utility, select Eject All Toner, 
and then click the Rotate Toner button.
The printer enters Eject All Toner mode, and the magenta toner indica-
tor lights up.
NoteTo exit Eject All Toner mode, press the Clear key.
2Perform the operations described in steps 3 through 11 of “Replacing a 
Toner Cartridge” startin on page 47 to replace the magenta toner 
cartridge.
3Follow the same procedure to replace the cartridges for the cyan, black, 
then yellow toners.
4Press the Cancel key to reset the printer and clear the indicator message.
NoteThe printer must complete a calibration cycle (less than 2 minutes) 
after a toner cartridge has been replaced. If you open the top or 
front cover before the printer is reset, the calibration stops, then 
starts over again after the cover is closed.
Downloaded From ManualsPrinter.com Manuals 
						

							54  -  C110 User’s Guide
Imaging Cartridges 
Replacing the Imaging Cartridge
Important!
For the best results, use only genuine Oki imaging cartridges. 
1Open the top cover.
NoteIf there is paper in the output 
tray, remove it, and then fold 
up the output tray before 
opening the top cover.
2Grab the handle and lift it up 
slightly to the back, and then 
slowly pull the imaging cartridge 
out vertically.
 
 
 
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals 
						

							55  -  C110 User’s Guide
CAUTION
Dispose of the used imaging cartridge according to your local 
regulations. Do not burn the imaging cartridge.
3Prepare the new imaging cartridge.
Important!
Do not touch the PC drum and the transfer belt on the imaging 
cartridge.
 
 
 
 
 
 
 
 
 
 
 
4Slowly insert the new imaging 
cartridge vertically, and then 
push it slightly down toward you 
to finish installing the imaging 
cartridge.
Downloaded From ManualsPrinter.com Manuals 
						

							56  -  C110 User’s Guide
5Carefully close the top cover.
NoteThe printer must 
complete a calibration 
cycle (less than 2 
minutes) after the 
imaging cartridge has 
been replaced. If you 
open the top or front 
cover before the printer is 
reset, the calibration 
stops, then starts over 
again after the cover is 
closed.
Downloaded From ManualsPrinter.com Manuals 
						

							57  -  C110 User’s Guide
The Fuser Unit
Replacing the Fuser Unit
Important!
For optimum print quality and performance, use only a genuine Oki 
fuser unit for your specific printer type.
1Turn off the machine and 
disconnect the power cord.
 
 
 
 
 
 
 
 
 
 
 
 
 
WARNING!
There are extremely hot parts within the machine. Before 
replacing the fuser unit, wait about 20 minutes after turning off 
the machine, and then check that the fusing section has reached 
room temperature, otherwise, you may get burnt.
Downloaded From ManualsPrinter.com Manuals 
						

							58  -  C110 User’s Guide
2Open the top cover.
NoteIf there is paper in the 
output tray, remove it, 
and then fold up the 
output tray before 
opening the top cover.
3Push the blue handles back as 
far as possible.
4Grab the blue handles and lift 
the fuser unit to remove it.
 
 
 
 
 
 
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals 
						

							59  -  C110 User’s Guide
Important!
Do not touch the matching 
connectors of the fuser unit 
and the machine. 
 
 
 
 
 
 
 
 
 
 
5Prepare a new fuser unit.
NoteBe careful not to touch 
the surface of the fuser 
roller.
Downloaded From ManualsPrinter.com Manuals 
						

							60  -  C110 User’s Guide
aPull the fuser separator 
levers forward as far as pos
-
sible.
bRemove the fuser separator 
material, and then return the 
fuser separator levers to their 
original positions.
 
 
 
 
 
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals