OKI B2500 MFP User Manual

							25. Replace the cleaned doctor blade assembly in the hopper. Install the lower brace first inserting the tail through the cartridge
wall and under the copper contact. Install the doctor blade next making sure the lip is facing down and the blade fits over the
alignment pins correctly.
OKIDATA B2500 MFP TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
26. Replace the upper metal brace and the two screws.
Clean the developer roller with a clean lint free dry cloth.
We do not recommend any chemicals be used at this time.27. Replace the developer roller into the cartridge.
The long metal shaft side goes to the gear side of the hopper.
Downloaded From ManualsPrinter.com Manuals 
						

							28. Replace the metal bushings on both sides of the developer roller shaft.
29. Replace the screw and holder on the gear side of the
developer roller shaft.30. Replace the screw, holder and contact on the contact side
of the developer roller shaft.
OKIDATA B2500 MFP TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
Downloaded From ManualsPrinter.com Manuals 
						

							31. Clean and replace the conductive grease on the developer
roller and the feed roller shafts. Note that the feed roller
contacts also run to the doctor blade. This helps ensure that
the toner is properly charged throughout the hopper.32. Fill the hopper with the Okidata B2500 toner.
Replace the fill plug.
33. Replace all the gears on the hopper as shown. 34.  Place  the  two  halves  together  and  install  the  two  metal
pins.
OKIDATA B2500 MFP TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
Downloaded From ManualsPrinter.com Manuals 
						

							35. Install the metal plates and screws.
36. Install the drum cover if available. It needs to be taped in
place. Use a brightly colored tape so the user will notice it.37. After the cartridge has been tested and bagged, tape the
Key card to the top of the bag so the user will see it. This key
card is installed into the printer separately from the cartridge.
OKIDATA B2500 MFP TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
Downloaded From ManualsPrinter.com Manuals 
						

							PRINTING A TEST PAGE:
The simplest way to test a cartridge is to make a copy:
1. To do this place the original face down in the feeder.
2. Press the copy key, number of copies desired and the start key.
CLEANING THE SCANNER:
If copied and transmitted pages come out with marks on the pages, but the reports are clean, the scanner is dirty:
1. To clean the scanner, open the scanner cover.
2. Wipe the scanner window down with a lint-free cloth moistened with Isopropyl alcohol.
REPETITIVE DEFECT CHART:
OPC Drum 75mm
Developer Roller 50mm
PCR 29mm
OKIDATA B2500 MFP TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
Downloaded From ManualsPrinter.com Manuals