Nortel T24 Key Indicator Module Installation Card Manual

							T24 KIM Installation 
T24 Key Indicator Module 
(KIM) Installation Card
The T24 Key Indicator Module (KIM) is an add-on device which provides 24 extra memory or 
line buttons for the T7316E telephone. Up to nine KIMs can be connected to a T7316E
telephone. 
A Station Auxiliary Power Supply (SAPS) is required for T7316E telephones that have five to 
nine KIMs attached. For SAPS installation instructions, refer to the SAPS Installation Card 
provided with the SAPS kit. 
Single T24 KIM installationMultiple T24 KIM installation
1
Position the metal hooks 
from the left side of the KIM 
next to the slots on the right 
side of the T7316E
telephone.
Firmly press the T7316E and KIM together.1Position the T7316E 
telephone and KIMs 
together. Align the 
hooks on each KIM 
to the slots on the 
next KIM. 
Firmly press the T7316E and KIMs together.
2Slide the KIM down until its 
aligned with the T7316E 
telephone. 2Slide the KIMs down 
until they are aligned 
with the T7316E 
telephone. 
3Remove the stand 
from the T7316E 
telephone.3Remove the 
stands from 
KIMs and 
the T7316E 
telephone.
4Connect the KIM 
cord to the accessory 
connector port on the 
T7316E telephone.4Connect each KIM 
cord to the connector 
port on the next KIM 
in a daisy-chain 
order.
5Replace the stand on the T7316E telephone to 
complete the installation.5Connect the cord 
on the first KIM 
to the accessory 
connector port on 
the T7316E 
telephone.
6Replace the stands on the KIMs and the 
T7316E telephone to complete the installation.
Press here 
to remove stand.
Press here 
to remove
stands.
KIM 1
KIM 2 KIM 3
KIM 1
 
Cord to
T7316E 
						

							2 
T24 KIM initialization
KIM indicators turn on and flash during the first ten seconds 
after powering up. It can take up to five minutes for the KIM 
to initialize.
The default setting for the programmable memory buttons 
on the KIM is blank. The side illustration shows the button 
number assignment on a KIM.
Troubleshooting Tip: An 

message appears 
on the T7316E telephone display and an error tone is 
generated when there is a connector problem with a KIM. 
Check that the KIM cord is properly inserted into the 
accessory connector port of the T7316E telephone.
T24 KIM coldstarts
Internal autodial numbers can be automatically assigned to the programmable memory buttons on the 
KIM when a coldstart is performed. Internal autodial numbers are assigned in ascending order starting 
on the top left button (button 01) on the KIM. A coldstart must be performed during the first ten sec-
onds after powering up a KIM. 
To coldstart an individual KIMTo coldstart all KIMs
1
Unplug the T7316E telephone line cord, then 
reconnect it to power up.1Unplug the T7316E telephone line cord, then 
reconnect it to power up.
2While the indicators are 
flashing on the individual 
KIM, simultaneously press 
the top two and the bottom 
two buttons on the lower 
button set of the KIM, as 
shown in the illustration
(buttons: 05, 12, 17 and 24).2While the indicators are 
flashing on the first KIM 
(next to the telephone), 
simultaneously press the 
top two buttons and the 
bottom two buttons on the 
KIM, as shown in the
illustration.
(buttons: 01, 12, 13 and 24)
3At the beginning of the coldstart, indicators beside 
each KIM button will briefly flash starting at the 
bottom right button (button 24).3At the beginning of the coldstart, indicators beside 
each KIM button will briefly flash starting at the 
bottom right button (button 24).
4When the KIM coldstart is completed, the T7316E 
telephone display automatically returns to the time 
and date.4When the KIM coldstart is completed, the T7316E 
telephone display automatically returns to the time 
and date.
B09
B10
B11
B12B08 B05
B06
B07
B20
B21
B22
B23
B24B17
B18
B19 B04 B01
B02
B03
B16 B13
B14
B15
1-800-4 NORTEL
www.nortelnetworks.com
P0603481_02
Printed in Canada
KIM button number assignment