Nortel Enterprise Edge M7310N Instructions Manual

							© 2000 Nortel Networks
P0908519  Issue 02
Enterprise Edge
M7310N
User Card 
						

							Page 1 Enterprise Edge M7310N User Card
Your Enterprise Edge M7310N Telephone
Using Button 
InquiryCheck what is programmed on your memory buttons.
1. Release all calls or lines with dial tone.
2. Press 
Ä¥â.
3. Press the button(s) that you want to check and read the display.
4. Press 
Ä when finished.
Adjusting display 
contrast1. Press Ä¥à.
2. Press
 UP or DOWN for the level you want.
3. Press
 OK when finished.
Selecting a ring 
type and volume 
level1. Press Ä¥ß.
2. Press 
Ú, Û, Ü, Ý, or NEXT to hear the different ring types.
3. While the telephone is ringing, press 
à to adjust the 
volume level.
4. Press
 OKÊto store the volume level and ring. Using display 
buttonsThree display buttons appear directly below 
the display. When they are active, these 
buttons are labelled in capital letters on the 
bottom line of the display. In  Enterprise Edge 
documents, display buttons are shown as 
underlined, capital letters: for example,
 OK.
is used to access the top function of a dual memory button
shows the time, date, and call information; guides you while
Display buttons
Release button
Hold button
Dial pad Feature button
Vo l u m e  c o n t r o l
Memory buttons
Dual memory buttonIndicators
Shift button
Display
  
						

							Page 2 Enterprise Edge M7310N User Card
Making and answering calls
Answering calls Answering calls using the handset
When your telephone rings, or 
¼ flashes beside an Intercom or line button:
1. Lift the handset.
OR
Press the button beside the flashing 
¼ before lifting the handset.
Answering calls using Handsfree
When your telephone rings, or 
¼ flashes beside an Intercom or line button:
1. Press 
©. 
Making calls Depending upon the dialing mode programmed on your telephone, you may 
have to lift the handset before making a call.
ÂExternal calls using numbered line buttons
1. If you do not have an external Prime line, press a line button.
2. Dial your call.
ÆExternal calls using Intercom buttons
1. Lift the handset.
2. If 
¼ appears beside an Intercom button, enter a line pool access code.
OR
Press an Intercom button without 
¼, then enter a line pool access code.
3. When you hear external dial tone, dial your call.
Internal calls using Intercom buttons
1. If you do not have an internal Prime line, press 
Æ.
2. Dial your call.
Note:  Line pool access codes and extension numbers are supplied by 
your System Administrator.
Making calls using Handsfree
1. Press 
© instead of lifting the handset.
úHolding Calls 
1. Press 
ú.  
  The ¼  flashes beside the line on hold.          
2. Press the line button with the flashing 
¼ to return to the call.
Automatic hold
Calls are put on hold automatically when you switch from one line to another.
Exclusive hold
Use Exclusive Hold (
Äú) to keep a call on hold so that it can be 
retrieved only at your telephone.
©System Administrator can program Handsfree for your telephone.
Switching between Handsfree and handset
1. Press 
© and replace the handset to switch to Handsfree.
2. Pick up the handset to switch back.
Using Mute
1. Press 
©microphone OFF.
2. Press 
© again to turn the microphone ON. 
						

							Page 3 Enterprise Edge M7310N User Card
Remember: Press Ä¥â to check a memory or line button. 
Notice These telephones now conform to the latest standards in relation to the 
positioning of Q and Z on the number buttons. The Q appears on button 
number 7 and the Z appears on button number 9.  Programming 
memory buttonsExternal Autodial
1. If you are on a call or an open line 
with dial tone, press 
ú or ¨.
2. Press Ä¥Ú. 
3. Press a memory button.
4. Dial the external number.
5. Press
 OK to store the number.
6. Label your new button.Internal Autodial
1. If you are on a call or an open line with 
dial tone, press 
ú or ¨.
2. Press Ä¥Û. 
3. Press a memory button.
4. Dial the station number.
5. Label your new button.
Features
1. If you are on a call or an open line 
with dial tone, press 
ú or ¨.
2. Press Ä¥Ü. 
3. Press a memory button.
4. Press 
Ä and the feature 
code.
5. Label your new button.Erasing memory buttons
1. If you are on a call or an open line with 
dial tone, press 
ú or  ¨.
2. Press Ä¥Ú. 
3. Press the memory button you want to 
erase.
4. Press
 OK to erase the button.
About memory buttons
Programming memory buttons
Memory buttons store telephone 
numbers or feature codes to give 
you one-touch dialling or 
feature activation.
To use the 
top function, press 
the shift button, then press the 
dual-memory button.
There are two types of memory 
buttons: single-memory and 
dual-memory.
Dual-memory buttons:
To use the 
bottom function, 
press the dual-memory button.
Single-memory buttons:
Single-memory buttons are the 
buttons with indicators other 
than line or Handsfree buttons. 
						

							Page 4 Enterprise Edge M7310N User Card
Setting up the telephone
Connecting the cordsATTENTION  Before attempting to carry 
out 
any work on the telephone, ensure that 
the line cord is unplugged from the wall 
socket.
To remove any of the cords, squeeze the 
release latch on the plug and gently pull 
the plug from the socket.
Connect the handset cord to the jack 
labelled with the telephone icon and route 
the cord as shown.
If you are using a headset, route the cord 
along the channel in the base and connect 
the cord to the telephone jack that is 
marked with the headset icon.
Route the line cord through the stand and 
connect the cord to the telephone jack that 
is marked with the jack icon.
Attach the stand using either pair of slots; 
to raise the back of the telephone to its 
highest position, use these slots.
Once the above work is complete, plug the 
line cord back into its wall socket.
Press here to 
remove the stand.
1
Press here firmly 
until it clicks, to 
attach the stand.
2
  
						

							Page 5 Enterprise Edge M7310N User Card P0908519  Issue 02
12 cm
Setting up the telephone
Mounting the 
telephone on
the wall