Nortel Enterprise Edge M7100 Instructions Manual

							© 1999 Nortel Networks
P0908517 Issue 01
Enterprise Edge
M7100
User Card 
						

							Page 1  Enterprise Edge M7100 User Card
Your Enterprise Edge M7100 telephone
Using Button 
InquiryCheck what is programmed on your memory button.
1. Release all calls or lines with dial tone.
2. Press 
Ä¥â.
3. Press the button that you want to check.
4. Read the display.
5. Press 
Ä when finished.
Adjusting the 
display contrast1. Press 
Ä¥à.
2. Press 
Ú to á for the level you want; the higher the number the higher 
the level.
Selecting a ring 
type and volume 
level1. Press 
Ä¥ß.
2. Press 
Ú, Û, Ü or
 Ý to hear the different ring types.
3. While the telephone is ringing, press 
à to adjust the 
volume level.
4. Press 
Ä to store the ring.
Adjusting the 
handset or 
telephone 
speaker volume1. Press 
à when using the handset or the speaker.
Display
shows the time, date, call information, and guides you.
Feature button
starts or ends a feature. Release button
cancels active calls
Hold button Dial pad
Volume control Memory button
is programmable to store a feature or to
automatically dial internal or external
number. 
						

							Page 2  Enterprise Edge M7100 User Card
Making and answering calls
Answering calls 1. When your telephone rings, lift your handset.
You are immediately connected to the call.
Making external 
callsDepending upon the dialling mode programmed for your telephone, you 
may be able to dial your call before lifting your handset.
1. Pick up the handset.
2. Dial 
â (your system’s exchange line access code or a line pool 
access code).
3. Dial the external telephone number.
Making internal 
calls
1. Pick up the handset.
2. Dial the internal number.
Note: Extension numbers and the exchange line access code are 
supplied by your System Administrator.
Making or 
answering a 
second call
The M7100 telephone allows you to have two calls active at the same 
time.
You can switch between calls using 
ú.
To answer a second call while on another call
1. Press 
ú to put the first call on hold.
The second call automatically comes onto the line.
To hold a call and make a second call
1. Press 
ú to put the first call on hold.
2. Dial the telephone number for the second call.
To return to the first call
1. Press 
ú again to return to the first call on hold.
The second call is automatically put on hold.
ú
To hold a call 
1. Press 
ú.
2. Press 
ú again to return to the call on hold.
Check the display for confirmation or additional information.
Note:  If you have difficulty selecting a line on your M7100 telephone, ask 
your System Administrator to check your telephones 
programming. Your telephone must be assigned to use an 
exchange line or line pool.
9 
						

							Page 3  Enterprise Edge M7100 User Card
Programming the memory button
Remember: Press Ä¥â to check a memory or line button.
Programming the 
memory buttonExternal Autodial
1. If you are on a call or a line with dial tone, press 
ú or ¨.
2. Press
 
Ä¥Ú.
 
3. Dial the external number.
4. Press 
ú to store the number.
5. Label your new button.
Internal Autodial
1. If you are on a call or a line with dial tone, press 
ú or ¨.
2. Press
 
Ä¥Û.
 
3. Dial the extension number.
4. Label your new button.
Features
1. If you are on a call or a line with dial tone, press 
ú or ¨.
2. Press
 
Ä¥Ü.
 
3. Press
 
Ä and the feature code.
4. Label your new button.
Erasing the memory button
1. If you are on a call or a line with dial tone, press 
ú or ¨.
2. Press
 
Ä¥Ú.
 
3. Press 
ú to erase the button.
Notice These telephones now conform to the latest standards in relation to the 
positioning of Q and Z on the number keys. The Q appears on key 
number 7 and the Z appears on key number 9.  About the 
memory buttonThe memory button can store a 
telephone number or feature 
code to give you one touch 
dialling or feature activation. You 
can change the memory button 
by programming it with a new 
number or feature code.
Memory button
Page 3  Enterprise Edge M7100 User Card 
						

							Page 4  Enterprise Edge M7100 User Card
Setting up the telephone
Connecting the cordsAT T E N T I O N Before attempting to carry 
out 
any work on the telephone, ensure 
that the line cord is unplugged from the 
wall socket.
To remove any of the cords, squeeze 
the release latch on the plug and gently 
pull the plug from the socket.
Connect the handset cord to the jack 
labelled with the telephone icon and 
route the cord as shown.
Route the line cord through the stand 
and connect the cord to the telephone 
jack that is marked with the jack icon.
Attach the stand using either pair of 
slots; to raise the back of the telephone 
to its highest position, use these slots.
Once the above work is complete, plug 
the line cord back into its wall socket.
Connect to jack 
from  distribution block
Connect to receiver 
						

							Page 5  Enterprise Edge M7100 User Card
Setting up the telephone
Mounting the
telephone on
the wall
Page 5  Enterprise Edge M7100 User Card P0908511  Issue 01