Nortel Bcm Ata 2 Instructions Manual

							Feature List  11
P0908546 Issue 01 Enterprise Edge ATA 2 User Guide
Priority Call
û¥á
Allows you to interrupt an internal call in progress on a digital telephone, or make 
a voice call to a digital telephone on Voice Call Deny or Do Not Disturb. The 
session in progress is automatically put on hold.
Note:Priority Call must be enabled in Enterprise Edge System Administration.
Privacy Control
û¥¡Ü
Prevents another telephone that shares your line from joining your current call or 
permits another telephone that shares your line to join in.
Restriction Override
û¥ß¡    
Allows you to override restrictions imposed on your telephone.
Ring Again
û¥Û
Allows you to queue a call to another Enterprise Edge or Centrex telephone that is 
busy or is not answered or to a busy line in the Line Pool. You can use ring again 
only on calls placed on an intercom line. When the telephone is available, you are 
alerted with one short ring from your telephone.
To cancel ring again, press û£Û.
Reply To a Ring Again Signal
To connect with a ring again request when you are on a call (or your telephone is 
off-hook):
1. Press ûÛ. This automatically places your call on hold.
2. To return to the caller on hold, press ûÛ.
To connect with a ring again request when your telephone is on-hook:
1. Lift the handset. The ring again number is automatically redialed.
Note:If you do not respond to a ring again signal within 30 seconds, ring 
again is canceled. 
						

							12  Feature List
Enterprise Edge ATA 2 User Guide P0908546 Issue 01
Saved Number Redial
û¥ßà
Allows you to save an external number while you are on a call or while the called 
telephone is ringing. To automatically redial the saved number:
1. Press û¥à.
Send Message
û¥Ú
Allows you to leave a message on a co-worker’s telephone.
To cancel send message, press û£Ú.
Ser vice Mode
In service mode the Enterprise Edge ATA 2 telephone can be assigned as the control 
telephone for one or more lines, or as the night zero telephone. Service mode is 
assigned during Enterprise Edge System Administration.
System Speed Dial
û¥â 
Allows you to use a speed dial code to quickly dial preprogrammed telephone 
numbers. System speed dial codes are established by the System Administrator.
Note:You cannot program personal speed dial numbers from your telephone.
To n e s
û¥¡âá
Call progress tones are audio signals heard through the handset or telephone ringer. 
Tones signal you about the progress of certain features.
To cancel tones, press û£¡âá.
Note:Tones must be OFF when Enterprise Edge ATA 2 is used with a data 
communication device such as a FAX or modem. 
						

							Feature List  13
P0908546 Issue 01 Enterprise Edge ATA 2 User Guide
Tr a n s f e r
Allows you to transfer a call. To transfer a call you must have an available intercom 
line.
Blind Transfer
1. Press û¥àâ. 
2. Press the transfer destination number.
3. Replace the handset.
Transfer using announce
1. Press û¥àâ (intercom dial tone is heard).
2. Press the transfer destination number.
3. Announce the call to the receiving party (optional).
4. Replace the handset.
Transfer using Conference
1. Press ûÛ.
2. Make the second call.
3.û¥Ü.
4. Replace the handset.
To Transfer an external call to a co-worker with a line appearance using Hold
1. Put the caller on hold and select your alternate line.
2. Call your co-worker. Tell your co-worker the flashing line appearance is a call 
for them.
3. Replace the handset.
Note:Your co-worker must have an Enterprise Edge telephone with line 
appearance. 
						

							14  Feature List
Enterprise Edge ATA 2 User Guide P0908546 Issue 01
Trunk Answer from any Telephone
û¥¡ââ
Allows you to pick up a ringing external call on a line that has been placed into any 
service mode.
Vo i c e  C a l l
û¥ßß 
Allows you to make a voice announcement or begin a conversation through the 
speaker of a digital telephone without making the other telephone ring. 
						

							P0908546 Issue 01 Enterprise Edge ATA 2 User Guide
Data Communication
This section supplies additional information for using Enterprise Edge Analog 
Terminal Adapter 2 with data communication devices.
Set Tones to OFF 
Enterprise Edge ATA 2 must have tones OFF so tones do not interfere with data 
transmissions.
The following progress tones are not heard when Enterprise Edge ATA 2 is in the 
tones OFF mode:
• Held Line Reminder
• Call Waiting
• Ring Again 
To turn tones OFF:
Lift the handset and press û£¡âá.
Auto-answer Modems and Answering Machines
Enterprise Edge ATA 2 can be programmed to ring directly on one external line. It 
can also be designated as the Night Set to answer calls after hours. To assign an 
external line to ring at the digital telephone, contact your Installer or System 
Administrator. 
Modem and FAX Transmission Compatibility
Enterprise Edge ATA 2 is compatible with all commercial FAX and modem 
protocols. When connected to Enterprise Edge ATA 2, the Enterprise Edge server 
supports data transmission rates up to and including 28.8 kbit/s.
Note:The maximum data transmission rate is subject to the quality of the end-to-
end channel and cannot be guaranteed. 
						

							16  Data Communication
Enterprise Edge ATA 2 User Guide P0908546 Issue 01 
						

							P0908546 Issue 01 Enterprise Edge ATA 2 User Guide
Troubleshooting for Data Applications
If you are having trouble, check the following before calling a repair person:
1. Make sure the data parameters (parity, baud) are set correctly.
2. Make sure Enterprise Edge Analog Terminal Adapter 2 is in the tones OFF 
mode.
3. Make sure you are dialing out on the proper line. The proper line is either an 
intercom or external line. See Alternate Line
 on page 6 of the Feature List. To 
change your prime line, see your System Administrator.
4. Substitute a single line telephone for your data communication device. If you 
receive a dial tone on the single line telephone, the problem can be with the 
data communication device. 
						

							18  Troubleshooting for Data Applications
Enterprise Edge ATA 2 User Guide P0908546 Issue 01