Nokia 8600 D Service Manual

							
CONFIDENTIAL
Copyright © 2007 NOKIA. All rights reserved.8600 Luna RM-64
Page(36)ISSUE 2
Service Manual Level &2
SW-UPDATE12.
Flash Concept – (Point of Sales)
To use FLS-5 Flash Dongle you have to follow the user guide inside the sales package. Please check always for the 
latest version of flash software, which is available on 
NOKIA Online. 
						

							
2CONFIDENTIAL
Copyright © 2007 NOKIA. All rights reserved.8600 Luna RM-64
Page(36)ISSUE 2
Service Manual Level &2
DISASSEMBLY INSTRUCTION13.
1. Nokia 8600 disassembly.2. You will need the Nokia Standard Toolkit version 2. Also refer 
to the General Mechanical Guideline Video for additional hints 
about the tools and component handling.
3. Unlock and remove the BATTERY COVER.4. Unscrew these 2 Torx Plus size 6 screws in the order shown 
and remove them.
5. Gently pry open the clips of the ANTENNA COVER ASSEMBLY 
with the SRT-6 and remove it.
6. The KEYPAD COVER ASSEMBLY can be shifted down and 
removed now. 
						

							
3CONFIDENTIAL
Copyright © 2007 NOKIA. All rights reserved.8600 Luna RM-64
Page(36)ISSUE 2
Service Manual Level &2
7. Carefully lift up and bend the BLACK KEYPAD.8. Now it can be removed easily.
9. This BLACK KEYPAD can be reused if the adhesive stays 
on the keypad. Otherwise it must be renewed when 
reassembling.
10. Gently push open the clips of the CAMERA COVER ASSEMBLY 
DECORATED with the SRT-6. Note: The material of the DISPLAY 
COVER is very delicate and can be scratched easily.
11. Flip over the CAMERA COVER ASSEMBLY DECORATED in order 
to release the clips on the opposite side. The cover can be 
removed now.
12. Remove the VOLUME KEY ASSEMBLY. 
						

							
4CONFIDENTIAL
Copyright © 2007 NOKIA. All rights reserved.8600 Luna RM-64
Page(36)ISSUE 2
Service Manual Level &2
13. Unscrew these Torx Plus size 4 screws in the order shown.14. Discard these screws. Do not use them again.
15. Slide the CAMERA BEZEL into the direction shown and 
remove it.
16. Unscrew these six Torx Plus size 4 screws in the order shown.
17. Discard these screws. Do not use them again.18. Remove the ANTENNA MOD CDMA. The clips of the KEYPAD 
COVER GUSSET will be released. 
						

							
5CONFIDENTIAL
Copyright © 2007 NOKIA. All rights reserved.8600 Luna RM-64
Page(36)ISSUE 2
Service Manual Level &2
19. Take away the KEYPAD COVER GUSSET.20. Lift up the RF SHIELD PAINTED.
21. Carefully lift up the SHIELD ASSEMBLY. Note that this 
assembly is still connected with the ENGINE MODULE.
22. Open the connector of the VIBRA MOTOR.
23. Unlock and remove the CAMERA MOD with the SS-45.24. Open the slider. Carefully open the flex connector with the 
SS-93. 
						

							
6CONFIDENTIAL
Copyright © 2007 NOKIA. All rights reserved.8600 Luna RM-64
Page(36)ISSUE 2
Service Manual Level &2
25. The ENGINE MODULE can be removed now.26. Unscrew these 2 Torx Plus size 4 screws in the order shown 
and remove them.
27. Discard these screws. Do not use them again.28. The DISPLAY COVER can be separated now.
29. Shift out the LCD CONNECTOR CLIP with the SS-93.30. Remove the clip from the connectors. 
						

							
7CONFIDENTIAL
Copyright © 2007 NOKIA. All rights reserved.8600 Luna RM-64
Page(36)ISSUE 2
Service Manual Level &2
31. Carefully disconnect these flex foil connectors with the SS-
93.
32. Remove the LCD AM 240x320.
33. Keep this adhesive clean if this part should be reused.34. Lift out the EARPIECE ASSEMBLY.
35. Release the UI FLEX ASSEMBLY, beginning at the volume 
dome sheet.
36. Now peel off the UI FLEX ASSEMBLY completely and discard it, 
do not use it again. 
						

							
8CONFIDENTIAL
Copyright © 2007 NOKIA. All rights reserved.8600 Luna RM-64
Page(36)ISSUE 2
Service Manual Level &2
37. The disassembly procedure is now complete. 
						

							
9CONFIDENTIAL
Copyright © 2007 NOKIA. All rights reserved.8600 Luna RM-64
Page(36)ISSUE 2
Service Manual Level &2
ASSEMBLY HINTS14.
1. Nokia 8600 assembly hints.2. You will need the Nokia Standard Toolkit version 2. Also refer 
to the General Mechanical Guideline Video for additional hints 
about the tools and component handling.
3. Peel up all protection films from the adhesive tapes of the 
UI FLEX ASSEMBLY.
4. When replacing the UI FLEX ASSEMBLY, check this guide at the 
bottom,...
5. and this pin at the top of the key Dome Sheet.6. Also note the guides at the Volume Key… 
						

							
20CONFIDENTIAL
Copyright © 2007 NOKIA. All rights reserved.8600 Luna RM-64
Page(36)ISSUE 2
Service Manual Level &2
7. and the EARPIECE-contacts flex foil.8. Place the EARPIECE ASSEMBLY.
9. Peel up this protective film if this part was renewed.10. Insert the LCD AM.
11. Close the connector of the LCD.12. Fit the LCD CONNECTOR CLIP.