Nokia 6120c1 User Manual

71
Date and time
Time and Date—to set the time and date
Time zone—to set the time zone of your location. If you set Network operator 
time> Auto-update, the local time is shown.
Date format—to select the format to display dates
Date separator—to select the date separator
Time format—to select between 24-hour and 12-hour time format
Time separator—to select the time separator
Clock type—to select whether the analog or digital clock is shown in the standby 
mode. See “Clock,” p. 63.
Clock alarm tone—to...

72
Avoid using access codes similar to emergency numbers to prevent accidental 
dialing of the emergency number.
Code in use—to select the active code, PIN or UPIN, for the active USIM. This is 
shown only if the active USIM supports UPIN, and the UPIN is not rejected.
PIN code request or UPIN code request—to set the phone to request the code each 
time the phone is switched on. Some SIM cards may not allow the PIN code 
request to be turned Off. If you select Code in use> UPIN, UPIN code request is...

73
Important: Even if the use of certificates makes the risks involved in remote 
connections and software installation considerably smaller, they must be used 
correctly in order to benefit from increased security. The existence of a certificate 
does not offer any protection by itself; the certificate manager must contain 
correct, authentic, or trusted certificates for increased security to be available. 
Certificates have a restricted lifetime. If Expired certificate or Certificate not 
valid yet is...

74
Factory settings
Reset some of the settings to their original values. You need the lock code. See 
“Lock code,” p. 19.
Positioning
With the positioning service you can receive information from service providers 
about local issues such as weather and traffic conditions, based on the location of 
your device (network service).
To enable a positioning method, select Positioning methods, scroll to the 
positioning method, and select Options> Enable. To stop using it, select 
Options> Disable.
To define...

75
Show call duration—to set the phone to display the call duration during a call
Summary after call—to set the phone to briefly display the approximate duration 
of the last call
Speed dialling> On—to set the phone to dial the numbers assigned to the speed 
dialing keys, 2 to 9, by pressing and holding the corresponding number key
Anykey answer> On—to answer an incoming call by briefly pressing any key, 
except the right selection key, volume keys, and the end key
Line in use (network service)—shown...

76
When calls are barred, calls may be possible to certain official emergency numbers.
Network
Network mode—To select which network to use (shown only if supported by the 
service provider). If you select Dual mode, the device uses the GSM or UMTS 
network automatically, according to the network parameters and the roaming 
agreements between the network operators.
Operator selection—To set the phone to search for and select automatically one of 
the available networks, select Automatic. To select the...

77
You may receive access point settings in a message from your service provider, or 
you may have preset access point settings in your phone.
To create a new access point or edit an existing access point, select Options> 
New access point or Edit. To create a new access point using the settings of an 
existing access point, scroll to an access point, and select Options> Duplicate 
access point.
Depending on the connection type selected in Data bearer, only certain settings 
are available. Fill in all...

78
Data call
The data call settings affect all access points that use a GSM data call.
Online time—to set the data call to disconnect automatically after a time-out if 
there is no activity. To enter a time-out, select User defined, and enter the time in 
minutes. If you select Unlimited, the data call is not disconnected automatically.
SIP settings
View and edit session initiation protocol (SIP) profiles.
Configurations
Certain functions, such as web browsing and multimedia messaging, may require...

79
To change voice command settings, select Options> Settings and from the 
following options:
Synthesiser—to activate or deactivate the text-to-speech syntheziser that says 
out loud the recognized voice command
Remove voice adapts.—to reset the voice adaptations. The phone adapts to the 
user’s voice to better recognize the voice commands.
14. Data management
■File manager
In the file manager, you can browse, open, and manage files and folders in the 
phone memory or on the memory card.
To see a list...

80
Format the memory card
When a memory card is formatted, all data on the card is permanently lost. Some 
memory cards are supplied preformatted and others require formatting.
1. Select Options> Format memory card.
2. Select Yes to confirm.
3. When formatting is complete, enter a name for the memory card.
Backup and restore information
To back up information from phone memory to the memory card, select Options> 
Back up phone memory.
To restore information from the memory card to the phone memory,...