Nitsuko Ds2000 Multibutton Telephone Quick Reference Guide

							1
2
3
4
5
6
7
8
9
0ABC DEF
MW ICM
FLASH DND
DIAL MIC
LND SPK
CONF
HOLD GHI JKL MNOMNO
PQRS TUV
OPER
VOLWXYZ
CLEAR
CHECK
80000 -62
LINE 1      LINE 2      LINE 3       LINE 4      LINE 5      LINE 6
LINE 7      LINE 8LINE 9 LINE 10 LINE 11 LINE 12 BIN 1        BIN 2        BIN 3        BIN 4        BIN 5
BIN 6        BIN 7        BIN 8        BIN 9       BIN 10
Using Your TelephoneThe Alphanumeric Displayhelps you use
features and tells you about your calls. It may
also show your caller’s name and number.The Ring/Message Lamp
:

Flashes slow
(green) while a call rings your phone.

Flashes fast (red) if you have new Voice Mail messages
or unanswered Message Waiting.
If you’re on a Handsfree call (see
Handsfree Optionsbelow), lift the
handsetfor privacy.The Volume Controlsare for speaker
and handset. They also control the volume
for ringing calls and pages. While on-hook,
these keys are for Contrast Control.
The Microphonepicks up your voice for
Handsfree calls. Press MICto turn off the
microphone.Press for Handsfreecalls, or use the
handset instead. See Handsfree Optionsbelow.
While on a handset call, press SPKtwice (do
not hang up) for Group Listen.Press ICMto place an Intercom call. Press Bin Key1-10 for Personal Speed Dial
bins 701-710. Press DIAL+ Bin Key1-10 for
Personal Speed Dial bins 711-720.
Due to the flexibility built into the system,
your dialing codesmay differ from
those in this guide. Check with your
communications manager and make a note
of any differences.
These are 
and/or keys.
Your key assignments may be different than
shown — ask your communications manager.
If you are an attendant . . .
Key 11 is a Night Key to put your system in
the night mode.
Key 12 (on 22-button telephone) or key 24
(on 34-button telephone) is an Operator Call
Key for your incoming Intercom calls.
MWflashes when you have Messages
Waiting. If you have Voice Mail, it flashes
when you have Voice Mail messages left in
your mailbox.Press a line key then LNDto automatically
redial the last outside number you called.
While on a call, pressCONFto set up a
Conference.Enable Do Not Disturbto block your calls
when you don’t want to be interrupted.
Soft Keyssimplify using your phone. To
guide you through your features, the Soft
Key functions automatically change to help
you handle calls. See the DS2000 Soft Key
Glossaryfor more.
Handsfree Options
• Handsfreelets you place and answer calls by pressing  instead of using the handset. • With Automatic Handsfree, you can press a line key without lifting the handset.
Normally, you have Automatic Handsfree.• Use Handsfree Answerbackto answer a voice-announced Intercom call by speaking
toward your phone — without lifting the handset.
22-Button Display Telephone Shown 
						

							Placing an Outside Call . . .
1. (Optional) Lift handset.
2. + Wait for dial tone + Dial number.
•If your system is behind a PBX, you
may have to dial 9 before your number.
OR
1. (Optional) Lift handset.
2. +  + Line number (e.g., 01) +
Dial outside number.OR
2. +  + (Optional) Line group
(0-8) + Dial outside number.
OR
2. +  + Line number (e.g.,
01) + Dial outside number.
1. (Optional) Lift handset.
2. Press an idle line key to preselect a line.
3. Press .
Calling a Co-Worker . . .
1. (Optional) Lift handset.
•For one-touch calling, press a Call
Coverage or Hotline function key.
2. Press .•For your Voice Mailbox: Press 
MW
.
•For Paging: Dial * 1 + Zone (1-7, 0 =
all call).
3. Co-worker’s extension number.•If you hear ringing, wait for an answer.
If you hear two beeps, begin speaking
(or dial 1 to have call ring).
Dial using the
Intercom:
To quickly redial your
last outside call:Dial codes for outside
lines:Press a line/loop key
for quick access:
Placing Calls
If your call doesn’t go through . . .Camp On and Callback
1. Dial  (to wait without hanging up).
•(Intercom calls) When you hear ringing,
wait for the called party to answer.•(Outside calls) When you hear new dial
tone, place your call again.OR
1. Dial  and hang up to leave a
Callbackfor a free line or extension.
•Wait for the system to call you back.
2. or lift handset.•(Outside calls) Place your call again.•(Intercom calls) Speak to co-worker.
Message Waiting 
(If you don’t have Voice Mail)
1. Do not hang up +  .
•Your co-worker’s 
MW
flashes fast.
•With Voice Mail, pressing 
MW
will leave
a message in your co-worker’s mailbox.
1. (Optional) Lift handset.
2. Press .
•If the extension you call is unanswered,
busy or in DND, the system cancels
Message Waiting.
1. Do not lift the handset.
2. Press .•Press 
MW
repeatedly until the exten-
sion you want to call displays.
3. Lift handset and press  .
To review your
Messages Waiting and
then select a message
for a return call:
To answer a Message
Waiting left for you:
Leave a Message
Waiting (flashing MW
key) if your co-worker
doesn’t answer:
When you hear sys-
tem busy, use Camp
On or Callback: 
						

							Directory Dialing
Answering Outside Calls . . .
1. or lift handset.
•Press line/loop key if not connected.
Answering Intercom Calls . . .
1. Speak toward your phone or lift the handset.
•If you hear one long ring instead, pressSPK
or lift handset to answer.
•Dialing 
#VA
+ V(#IR
in some systems)
makes incoming Intercom calls ring
your phone.
•Dialing 
#VA
+ R(#IV
in some systems)
makes incoming Intercom callsvoice-
announce your phone.
Picking up calls not ringing your phone . . .
1. or lift handset.
•You can press a Group Call Pickup or Call
Coverage key instead — then skip step 2.
2. + Co-worker’s extension.
Have a telephone meeting (Conference) . . .
1. Place/answer call +  .
2. Place/answer next call + .
•Repeat this step to add more parties.•If you hear error tone, you cannot add
additional parties.
Use Conference to
have a telephone
meeting:
When a call is ringing
a co-worker’s phone:Listen for two short
beeps:If you hear ringing and
see a flashing line key:
Answering Calls
To set up a telephone meeting:Make a Page announcing
Conference + Do not hang up + ICM+ Dial #11or #12.
To join the Conference: ICM+ Dial #11or #12. (If you wait too
long to dial, you may not be able to join the meeting.)
Meet Me
Conference:
(Check with your communications manager before using
this feature.)
1.D.
2. Dial Directory Dialing type:
I= Co-worker’s extensions.
C= System Speed Dial.
P= Personal Speed Dial.
3. Dial the first letter of the desired name (e.g., dial 4
if the first letter begins with G, H or I).
OR
Press VOL or VOL to scroll alphabetically
through the selected directory. To call the displayed
name, just press DIAL.
4. Look at your phone’s display and dial the digit for
the letter/number you want to call (e.g., if the name
in step 3 began with G, dial 1).
5. Press VOL or VOL to scroll through all the
names/numbers that begin with the letter/number
you selected.
6. Press DIALto have the system dial your call.
At your display
telephone, select a
co-worker or outside call
from a list of names
(rather than dialing the
phone number):
Quick Reference for Other Features
Do not lift handset + Dial ✽+ Dial outside number + Press line key to dial
the displayed number.
Dial Number
Preview:
To initiate:While on a handset call, press SPKtwice (do not hang up). 
To switch Group Listen to Handsfree:Press SPKtwice.
To cancel:Do not hang up + Press SPK. 
Group Listen:
To activate:Press MIC(key on).
To cancel:Press MIC(key off).
Microphone
Mute:
To activate:Press DND.
To cancel:Press DND.
Do Not Disturb: 
						

							4 Forest Parkway
Shelton, CT 06484
TEL:
203-926-5400  
FAX
: 203-929-0535
Your call can wait at your phone . . .Hold
1. Do not hang up +  .
•Your co-workers can retrieve your
System Hold calls. To place the call on
Exclusive Hold, press 
HOLD 
twice.
•Intercom calls automatically go on
Exclusive Hold when you press 
HOLD
.
1. or lift handset.
2. Press flashing , 
OR
2. if the call was not on a line/loop key
(or was an Intercom call).
•You may be able to press 
ICM
+*4
+
line number (e.g., 01) to pick up a call
on Hold at a co-worker’s phone.
Send the call you’re on to a co-worker . . .Transfer
1. + Dial your co-worker’s extension.
•To transfer the call to Voice Mail, pressMW
after dialing your co-worker.
OR
1. (Hotline or Call Coverage).
Park a call in orbit
1. +  + System Park Orbit (60-69).
•If you hear busy, press 
ICM
and try
another orbit.
•To Page, press
ICM
, dial * 1 and the
zone number (1-7, 0 for all call).
2. Hang up.
Park your current call
in a system orbit so
your co-workers can
pick it up:Send (Transfer) your
current call to a
co-worker:Easily retrieve a call
from Hold:
Use System Hold
instead of leaving the
handset off-hook:
Handling Your Calls
165 Matheson Blvd. E., Unit #4-6
Mississauga, Ontario L4Z 3K2TEL:
905-507-2888  
FAX
: 905-507-2971
User Programmable Features
To program a feature, press 
# and the feature’s code. For example, to enable incoming Paging, press 
# and dial 
V P Y, 
then 
SPK
 to hang up. The underlined codes (e.g., #RC
) are for systems prior to 02.00.00.
Feature Mnemonic OperationDSS
#BLF
#BLF
 + Press DSS key + 
HOLD
 + Enter extension + 
VOL Up
 + Pro-
gram another key or 
SPK
 to exit.
Headset
#HS
#HS
 + Y to enable or 
N to disable + 
SPK
 to exit
Hotline
#HL
#HL
 + Press flashing Hotline key + Enter extension for new Hotline 
partner + Program another Hotline key or 
SPK
 to exit.
Off Hook Signaling
#OHS
#OHS
 + Select mode (
C=Outside line, 
D=DSS, 
I=ICM) + Select 
option (see below) + 
SPK
 to exit.
Outside line options:
 C=Camp On tone, 
O=Off Hook Ringing, 
0 = None
Inter
com options:
 C=Camp On, 
O=Off Hook Ringing, 
V=Voice 
Over, 
0 = None
DSS Options:
 C=Camp On, 
O=Off Hook Ringing, 
0 = None
Paging (Incoming)
#VP
#VP
 + Y to enable or 
N to disable + 
SPK
 to exit.
Prime Line Assignment
#PLA
#PLA
 + Press one of your flashing programmable keys or 
ICM
 + 
SPK
 to exit.
Programmable Function 
Key Assignments
#KP
#KP
 + Press key you want to program + 
HOLD
 + ICM
 + Press 
VOL 
Up
 or VOL Down
 to select key option + 
HOLD
 + enter any addi-
tional data (if required) +  Press 
VOL Up
 or VOL Down
 to select 
another key to program, or 
SPK
 to exit.
Programmable Function 
Key Ringing
#RAC
#RC
Call Co
verage Keys: #RAC
 + Call Coverage Key repeatedly to select 
ringing mode + 
SPK
 to exit.
Call Coverage Keys flash as follows: Lamp only=On red, Immediate 
ring=On green, Delay ring=Fast flash green.
#RAL
#RL
Outside Line K
eys: #RAL
 + Line Key repeatedly to select ringing 
mode + 
SPK
 to exit.
Line keys flash as follows: Lamp only=On red, Immediate ring=On 
green, Delay ring=Fast flash green, Night ring=Slow flash green.
#RAP
#RG
Group Call Pic
kup K
eys: #RAP
 + Group Call Pickup Key repeatedly 
to select ringing mode  + 
SPK
 to exit.
Group Call Pickup Keys flash as follows: Lamp only=On red, Imme-
diate ring=On green, Delay ring=Fast flash green.
Ringing Line Preference
#RLP
#RLP
 + Y to enable or 
N to disable + 
SPK
 to exit.
Speed Dial, Personal
#SP
#SP
 + Press bin key (for bins 701-710) or 
DIAL
 then bin key (for 
bins 711-720) + 
HOLD
 + Enter outside line (e.g., 1), line group (e.g., 
90), or 
ICM
 for Intercom feature + 
HOLD
 + Number to store + 
HOLD
 + Name + 
HOLD
 + Press another bin key or 
SPK
 to exit.
Speed Dial, System
#SP
#SP
 + Dial System Speed Dial bin number (e.g., 200) + 
HOLD
 + 
Enter outside line (e.g., 1), line group (e.g., 90), or 
ICM
 for Intercom 
feature + 
HOLD
 + Number to store + 
HOLD
 + Name + 
HOLD
 + 
Press another bin key or 
SPK
 to exit.
Time and Date
#TD
#TD
 + Enter time in 24-hour clock using hours (2 digits), minutes (2 
digits) and seconds (2 digits) + 
HOLD
 + Enter date using month (2 
digits), day (2 digits) and year (4 digits) + 
HOLD
 + SPK
 to exit.
Voice Announce (for your 
incoming Intercom calls)
#VA
#IV, #IR
#VA
 + V for voice announce or 
R for ring + 
SPK
 to exit. 
						

							Quickly dial co-workers and outside calls . . .Speed Dial
1. .
•In some systems you may have to pressICM
and dial 
##
instead.
2. Dial Personal bin number (701-720).
OR
Press bin key (for bins 701-710), or 
DIAL
+
bin key (for bins 711-720).
3. .
4. Enter the line number (e.g., 1 for line 1) the
system will use for your stored number.
OR
Enter the line group number (e.g., 90-98
for line groups 0-8) the system will use for
your stored number.
OR
Skip this step if storing Intercom codes.
5. .
6. Enter the number to store +  .
•You can enter up to 30 digits, using 0-9,
# and *. Press 
MIC
to insert a pause;
FLASH
to insert a Flash.
7. Enter a name for your Speed Dial number.
•Refer to Keys for Entering Names. 
8. .
9. Repeat from step 3 to program another
Personal Speed Dial number.
OR
to exit.
To store Personal
Speed Dial numbers
(Intercom codes or
outside numbers):
Park a call in orbit
(Cont’d)
1. or lift handset.
2. +  + System Park Orbit (60-69).
1. Do not hang up.
2. +  + Extension (e.g., 300).
•To Page before hanging up, press
ICM
,
dial * 1 and the zone number (1-7, 0 for
all call).
3. Hang up.
1. (Optional) Lift handset for privacy.
2. +  + Extension (e.g., 300).
Forward (reroute) your calls to a co-worker . . .
1. (Optional) Lift handset for privacy.
2. + .
3. Dial Call Forwarding type:
0= Cancel forwarding2= Busy/No Answer4= Immediate6= No Answer
4. Dial destination extension (or 0 for your
operator).
OR
Press 
MW
or dial Voice Mail master exten-
sion number to forward to Voice Mail.
5. Hang up.
While at your desk or
out of the office, for-
ward your calls to a
co-worker or Voice
Mail:
To retrieve a call
parked at a co-worker’s
extension:Park a call at a
co-worker’s extension:
To retrieve a call from
system orbit:
Placing Calls Quickly 
						

							Speed Dial
(Cont’d)
1. Press 
Bin Key
for Personal Speed Dial
bins 1-10.
OR
Press 
DIAL
plus 
BIN KEY
for Personal
Speed Dial bins 11-20.
OR
Press Programmable Function Key
assigned to Personal or System Speed
Dial bin.
1. (Optional) Lift handset for privacy.
2. + .
3. Dial Personal Speed Dial bin number
(701-720).
OR
Dial System Speed Dial bin number (nor-
mally 200-299).
To dial a stored
System or Personal
Speed Dial number:
For one-touch access
to your stored Speed
Dial numbers:
Multibutton Telephone
Quick Reference Guide
80000MBG03
May 2000
Printed in the U.S.A. (2562)
Keys for Entering Names
Press this 
key:
Then one of these keys to enter the character in the white cell:1
2
3
4
#
1&
-
 (dash)1
/ (backslash)1
‘ (apostrophe)1
1
2ABC 23DEF 34GH I 45JKL 56MNO 67PQRS78TUV 89WX Y Z 90SPACE : 0**#
To enter characters in lower case (e.g., 
e instead of 
E), press 
MW
 before pressing the key in the 
first shaded column. Use 
LND
 to backspace over (erase) any characters you want to correct.
1In software versions prior to 02.00.00, the codes for 1 + 2, 1 + 3, and 1 + 4 were not available.