Nitsuko Ds2000 Hardware Manual

4. Optional
Equipment
4-23
WALL-MOUNT KIT

To remove the telephone from the wall mount kit
(Figure 4-13):
1. From the front of the phone, grab the tabs that secure the
telephone to the wall-mount kit.
2. While pressing in the tabs, lift up the phone until it snaps
clear of the wall-mount kit.
Figure 4-13  REMOVING THE WALL MOUNT BRACKET
80000 - 45
Press down tabs
on phone and
pull bracket in
direction of arrows 

4-24
— For Your Notes — 

4. Optional
Equipment
4-25
Using the Desk Stand (Figure 4-14)
Each telephone has an integrated desk stand. You can extend
the desk stand in one of two positions: low and high.
To use the desk stand low position:
1. Flip up each telephone leg until it snaps into place.
To use the desk stand high position:
1. Flip up each telephone leg into the low position.
2. Push out the leg extender.
3. Slide the extender up, then down until it locks in place as
shown at right.
Figure 4-14  USING THE DESK STAND
80000 -...

4-26
REJ RECORDING JACK
Installing the REJ Recording Jack (Figure 4-15)
Use the REJ Recording Jack (P/N 80175) to connect a Super
Display or 34-Button Display Telephone to an external tape
recorder or amplifier. The REJ output is a mono sub-miniature jack
which connects directly to an AUX level input. The REJ broadcasts
both sides of your conversation (i.e., your voice and your caller’s
voice) whenever you lift your handset. The REJ does not broadcast
Paging announcements or activate for Handsfree...

4. Optional
Equipment
4-27
REJ RECORDING JACKFigure 4-15  INSTALLING THE REJ
80000 - 48To mono AUX input on amplifierRed wire 

4-28
REJ RECORDING JACK
— For Your Notes — 

5. Maintenance
Options and SMDR
5-1
Section 5, MAINTENANCE OPTIONS AND SMDR
In this section . . . PageSMDR  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8
Installing SMDR . . . . . . . . . . . . . . . . . . . . . . 5-8
Programming SMDR . . . . . . . . . . . . . . . . . . . 5-8
Modem Installation  . . . . . . . . . . . . . . . . . .5-10
Installing a Modem . . . . . . . . . . . . . . . . . . . . 5-10
Making your own Data Cables  . . . . . . . . .5-12
In this section . . . PageBacking Up Site...

5-2
02.00.00 Compatibility
Keep the following PC Card data base compatibility guidelines in mind when backing up
and restoring site data:

All u slot software version 02.00.00 data bases in systems using CPU P/N 80025A
are
compatible (regardless of whether they are installed in a 4 or 8 slot cabinet).


U slot software version 02.00.00 data bases in systems using CPU P/N 80025 ar
e not
compatible with data bases using CPU P/N 80025A.


Fixed slot data bases are not compatible with any
u slot data bases. 

5. Maintenance
Options and SMDR
5-3
BACKING UP SITE DATA
Backing Up Site Data with a PC Card (Figure 5-1)
You can use PC Card P/N 85880 or P/N 80050-V**.** (with
system software preloaded) to back up and restore your site data.
Figure 5-1  USING THE PC CARD

To use the PC Card to back up site data:
1. Insert the PC Card into the CPU.
2. Be sure the CPU mode switch is set to 
RUN
.
3. Enter the programming mode.
ICM + #*#* + 372000 + HOLD
4. Dial 9906 + HOLD.
You see: START?
To quit program 9906 instead,...

5-4
BACKING UP SITE DATA
Figure 5-2  ENTERING NAMES7. When you are done entering the name, press HOLD.
You see the name and date of the first database stored.
If no data bases are stored, you see:
9906: DB00
(empty)
8. The system assigns the name you entered in step 7 to the
data base address you select below:
- Press VOLor VOLto scroll through the addresses.
U Slot has 8 data base addresses: DB 00 to DB 07
Fixed Slot has 12 addresses: DB 00 to DB 11
OR
- Skip this step to select the currently...