Nitsuko Ds1000 Hardware Manual

							4. Optional
Equipment
4-21
WALL-MOUNT KIT

To remove the telephone from the wall mount kit
(Figure 4-11):
1. From the front of the phone, grab the tabs that secure the
telephone to the wall-mount kit.
2. While pressing in the tabs, lift up the phone until it snaps
clear of the wall-mount kit.
Figure 4-11  REMOVING THE WALL MOUNT BRACKET
80000 - 45
Press down tabs
on phone and
pull bracket in
direction of arrows 
						

							4-22
— For Your Notes — 
						

							4. Optional
Equipment
4-23
Using the Desk Stand (Figure 4-12)
Each telephone has an integrated desk stand. You can extend
the desk stand in one of two positions: low and high.
To use the desk stand low position:
1. Flip up each telephone leg until it snaps into place.
To use the desk stand high position:
1. Flip up each telephone leg into the low position.
2. Push out the leg extender.
3. Slide the extender up, then down until it locks in place as
shown at right.
Figure 4-12  USING THE DESK STAND
80000 - 46
DESK STAND 
						

							4-24
REJ RECORDING JACK
Installing the REJ Recording Jack (Figure 4-13)
Use the REJ Recording Jack (P/N 80175) to connect a Super
Display or 34-Button Display Telephone to an external tape
recorder or amplifier. The REJ output is a mono sub-miniature jack
which connects directly to an AUX level input. The REJ broadcasts
both sides of your conversation (i.e., your voice and your caller’s
voice) whenever you lift your handset. The REJ does not broadcast
Paging announcements or activate for Handsfree calls.
CAUTION
Be sure the connected audio device provides a standard AUX
level input.
To install the REJ Recording Jack:
1. Unplug the telephone line cord and handset cord, and turn
the telephone face down on a non-abrasive surface.
2. Remove the 4 screws that secure the telephone base.
3. Separate the telephone faceplate from the telephone base.
4. On the left side of the telephone base, remove the plastic
molding that covers the hole for the REJU connector. Yo u
only need to remove the top half of the molding.
5. Install the REJ as shown (with the components facing down).
6. Secure with the supplied screw.

To connect the REJ Recording Jack:
1. Route the REJ wires through the guides in the telephone base.
2. Plug the REJ cable into the connector in the telephone PCB.
The connector is keyed so you can’t plug in the cable
the wrong way.
3. Reassemble the telephone, plug in the handset, and recon-
nect the line cord.
4. Using an audio cable, connect the REJ to the amplifier’s
mono AUX  input.
To connect to a stereo AUX input, use a commercially
available mono-to-stereo splitter cable. 
						

							4. Optional
Equipment
4-25
REJ RECORDING JACKFigure 4-13  INSTALLING THE REJ
80000 - 48To mono AUX input on amplifierRed wire 
						

							4-26
REJ RECORDING JACK
— For Your Notes — 
						

							5. Maintenance
Options and SMDR
5-1
Section 5, MAINTENANCE OPTIONS AND SMDR
In this section . . . PageMaking your own Data Cables  . . . . . . . . . .5-6
System Reset  . . . . . . . . . . . . . . . . . . . . . . . .5-7
Resetting Your System . . . . . . . . . . . . . . . . . . 5-7
In this section . . . PageSMDR  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Installing SMDR . . . . . . . . . . . . . . . . . . . . . . 5-2
Programming SMDR . . . . . . . . . . . . . . . . . . . 5-2
Modem Installation  . . . . . . . . . . . . . . . . . . .5-4
Installing a Modem . . . . . . . . . . . . . . . . . . . . . 5-4 
						

							5-2
SMDR
Installing SMDR (Figure 5-1)
Station Message Detail Recording (SMDR) provides a record
of the system’s outside calls. Once set up in programming,
SMDR automatically outputs from the system’s RS-232 (serial)
port to a customer-provided printer, terminal or SMDR data
collection device.
You can also connect a PC to the system serial port to
collect call history data.
To connect an SMDR device:
1. Plug one end of a mod-8 (standard 8 conductor) patch cord
into the system’s RS-232 port.
2. Plug the other end of the mod-8 patch cord into the DB9 to
Mod-8 Adaptor (P/N 85980).
3. Plug the adaptor into the DB9M COM connector on the back
of your PC.
The default communications parameters of the CPU
serial port are 19200 8 N 1 (19200 baud, eight data
bits, no parity and 1 stop bit).
If you have a PC connected to collect history data,
press Shift 1 to turn history on and off. 
Programming SMDR 

0301: CPU Baud Rate
Assign the baud rate for the RS-232-C port on the CPU. The
options are 0 (1200), 1 (2400), 2 (4800), 3 (9600), 4 (19200),
and 5 (38400).
You can also press Ctrl Break on a PC connected to
the system serial port to toggle through the available
system baud rates.
0301: SMDR Port
Enter 1 to enable SMDR output from the system’s RS-232-C port.
0301: Print SMDR Header
Enter Y to have the beginning of the SMDR report include the
column header data. Enter N to have the SMDR report only
include the call data (without the header). 
1001: Print SMDR
Enter Y to have the SMDR report include calls on the trunk.
Enter N to have the SMDR report exclude calls on the trunk. 
						

							5. Maintenance
Options and SMDR
5-3
SMDR
Figure 5-1  CONNECTING SMDR
80200 - 23
DB9M COM PORT
RS-232 Port
P/N 85980
Mod 8
Patch Cord 
						

							5-4
MODEM INSTALLATION
Installing a Modem (Figure 5-2)
You can connect a modem to the system’s serial port to remote-
ly collect history data and/or SMDR.
To connect a modem:
1. Plug one end of a mod-8 (standard 8 conductor) patch cord
into the system’s RS-232 port.
2. Plug the other end of the mod-8 patch cord into the DB25 to
Mod-8 Adaptor (P/N 85981).
3. Plug the other end of the adaptor into the DB25F connector
on the back of your modem.
The default communications parameters of the system’s
serial port are 19200 8 N 1 (19200 baud, eight data
bits, no parity and 1 stop bit).
If you have a PC connected to collect history data,
press Shift 1 to turn history on and off. 

To call from a PC at a remote site:
The remote PC must have a modem connected. Also,
the default communications parameters of the system’s
serial port are 19200 8 N 1 (19200 baud, eight data
bits, no parity and 1 stop bit).
1. Using commercially available communications software, dial
the phone number of the trunk connected to the modem at
the telephone system site.
2. To test history, type Shift 1 on the remote PC.
If history doesn’t output correctly, press Ctrl Break on
the remote PC to toggle through the available CPU
baud rates.