Nikon Camera Coolpix P610 Reference Manual

E37
Reference Section
When editing movies, use a sufficiently charged battery to prevent the camera 
from turning off during editing. Wh en the battery level indicator is B, movie 
editing is not possible.
Extracting Only the Desired Portion of a Movie
The desired portion of a recorded movi e can be saved as a separate file. 
1Play back a desired movie and pause at the start point of 
the portion that you want to extract (E36).
2Use the multi selector  JK to 
select the  I control, and then 
press the  k...

E38
Reference Section
5Use  HI  to select  m (save) and 
press the  k button.
•Follow the instructions on the screen to save 
the movie.
BNotes About Movie Extracting
•A movie that was created by editing cannot be edited again.
• The actual trimmed portion of a movie may di ffer slightly from the portion selected 
using the start and end points.
• Movies cannot be trimmed so that th ey are less than two seconds long.
Saving a Frame from a Movie as a Still Image
The desired frame of a recorded movie can...

E39
Reference Section
Set Time zone and date  (E 97) correctly before using the location data 
functions.
1Set  Record location data  to On.
•After the settings are complete, press the 
d  button or shutter-release button to exit 
the menu.
• To receive signals easily, operate in an open-
air area.
2Check the location data 
reception on the shooting 
screen.
•n  or o : Signals are being 
received from four or more satellites, 
or from three satellites, and 
positioning is being performed. The 
location...

E40
Reference Section
BNotes About Location Data Functions
•Before using the location data functions,  read “ Notes About Location 
Data Functions (GPS/GLONASS)” ( Axi).
• It takes a few minutes to obtain location  data when positioning is performed for 
the first time or in a situation where positioning cannot be performed for a long 
period of time, or  just after the battery is replaced. 
Using the latest A-GPS file can shorten th e time needed for obtaining the location 
data (E 93).
• Positions of...

E41
Reference Section
CPoints of Interest (POI) Information
•POI information is location name information for 
landmarks (facilities) and other details.
• When  Display POI  in Points of interest (POI)  
( E 95) of the location data options menu is set 
to  On , the nearest location name information for 
the current position is displayed during shooting 
(only when positioning is being performed).
• When  Embed POI  is set to On, location name 
information can be recorded on the image 
during shooting...

E42
Reference Section
1Use the multi selector HI to 
select Log interval, and press the k button.
2Select the intervals of log 
recording, and press the  k 
button.
• The default setting is  15 s.
3Select  Start log , and press the  k 
button.
4Select the duration that the log 
will be recorded, and press the  k 
button.
• Log recording starts. Press the  d button 
to exit the menu.
• D  is displayed on  the shooting screen 
during log recording ( A5).
• When a preset time has elapsed, log 
recording...

E43
Reference Section
BNotes About Log Recording
•If the date and time are not set, the log cannot be recorded.
• Use a fully charged battery to prevent th e camera from turning off during log 
recording. When the battery power becomes exhausted, log recording ends.
• Even when the camera is turned off, log  recording is continuously performed until 
the preset time has elapsed if there is still time remaining for log recording.
• Log recording ends due to the operations below even when there is time...

E44
Reference Section
Ending Log to Save it on Memory Cards
After the obtained log is sa ved to a memory card by using  Save log in the 
location data options menu, view the log with software that can display log 
data.
1When log recording is completed, 
select  End log  on the screen, and 
press the  k button.
•Ending log can also be performed before 
the preset time elapses.
2Select  Save log , and press the k  
button.
• The log data is saved to a memory card.
• To confirm that the log data is saved...

E45
Reference Section
1Press the  q (Wi-Fi) button on the 
camera.
• The screen shown on the right is displayed.
• If no connection conf irmation is received 
from the smart device within 3 minutes, the 
message  No access.  is displayed and the 
camera returns to the Wi-Fi options screen.
• You can also select  Connect to smart 
device  in the Wi-Fi options menu to 
display the screen shown on the right.
2Set the Wi-Fi setting on the smart device to On.
• Check the user’s manual provided with your smart...

E46
Reference Section
BNotes About Shooting
•When Wi-Fi is connected,  Intvl timer shooting in Continuous  cannot be used.
• Operations cannot be perfor med on the camera during remote control operation. 
The shooting mode is set to A  (auto) mode and the focus area is set to the center 
of the frame, regardless of the camera's settings.
CTouching an NFC-compatible Smart Device to the Camera for a 
Wi-Fi Connection
When you use a smart device that is compatible 
with near field communication (NFC)...