Netgear Prosecure Utm25s Manual

							125463
7. Kensington lock9. Module selection for console 11. Power connector
8. Factory reset button 10. Console port 12. Power switch
7
10
9
81112
Installation Guide
Connect the Unit
For initial setup, connect the WAN Ethernet port to an active WAN connec\
tion such 
as a broadband modern, connect a DHCP enabled computer to a LAN port, an\
d 
turn on the unit. Verify the following:
•     Power LED: It takes about a minute to boot. The power LED should turn solid 
green. If it does not, see the Troubleshooting section of the  Reference Manual. 
•     Test LED: When you first turn on the unit, the amber test LED is lit for  approximately 2 minutes. 
•     WAN Status LED: The status LED on the connected WAN port should be lit. If  not, make sure that the Ethernet cable is securely attached to the modem\
 and 
the WAN port, and that the modem is powered on. 
•      LAN Status LED: A LAN status LED should be lit. If not, ensure that the Ethernet 
cable from the computer to the unit is securely attached at both ends, a\
nd that 
the computer is turned on.
Log in to the Unit
1.    Use a browser to connect to https://192.168.1.1 
https://192.168.1.1.
2.    When prompted, enter admin  for the 
User Name and  password for the 
Password. Click  Login.  
 
You are now connected. After 5 minutes of  inactivity (the default login time-out), you 
are automatically logged out.
Note:  When the unit scans secure HTTPS 
traffic, import its root CA certificate into client 
browsers. Click the link on the login screen to 
download it.
Use the Setup Wizard for Basic Configuration
The Setup Wizard guides you through the basic network and scanning setup\
. 
Note:  If you choose to bypass the Setup Wizard, be sure to configure an alerts\
 
email address and change the admin password.
1.    Start the Setup Wizard.
Select  Wizards > SetupWizard  
to start the wizard.
For guidance on how to fill in 
the wizard screens, refer to the 
online help or the reference 
manual via a link in the 
Support > Documentation 
page.
ProSecure Unified Threat Management Appliance UTM25S
Note: Electronic License
This product includes an electronic license
that activates automatically upon product registration.
Follow these instructions to configure your ProSecure® Unified Threat\
 
Management appliance UTM25S appliance to use a single WAN interface, and\
 
enable the default threat management scanning. Then, consult the referen\
ce 
manual  for instructions for configuring other options such as multiple WAN sett\
ings, 
VPN, firewall, and custom scanning. You can access the reference manual  from the 
product management interface, via the resource CD and from the NETGEAR 
support site: http://downloadcenter.netgear.com . 
Estimated time: 30 minutes.
Verify the Package Contents
•     ProSecure UTM25S appliance 
•     Installation guide
•     Resource CD
•     Rubber feet (4) with adhesive backing
•     Rack mount brackets (some models)
•     Power cord
Familiarize Yourself with the Unit and Complete Setup
Familiarize yourself with the ports
and LEDs on the front of the unit.and with the 
connectors and controls on the back of the unit.
1. Power and Test LEDs 2. USB port (future use) 3. Gigabit LAN ports
4. LAN port 4 DMZ  5. Gigabit WAN ports, 6. Accessory modules
UTM25S_IG_13Sept2012.fm  Page 1  Thursday, September 13, 2012  3:28 PM 
						

							August 2012
For the complete EU Declaration of Conformity, visit  
http://support.netgear.com/app/answers/detail/a_id/11621/.
For indoor use only in all EU countries and Switzerland.
This symbol appears in accordance with the European Union Directive 2002\
/96 on the Waste 
Electrical and Electronic Equipment (the WEEE directive). If you dispo\
se of this product in the 
European Union, treat and recycle it in accordance with your jurisdictio\
n’s laws that implement the 
WEEE directive.
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks an\
d/or registered trademarks of 
NETGEAR, Inc. and/or its subsidiaries in the United States and/or other \
countries. Information is subject to 
change without notice. Other brand and product names are registered trad\
emarks or trademarks of their 
respective holders. © NETGEAR, Inc. All rights reserved.
2.    Use the Setup Wizard to configure these basic network and scanning setti\
ngs:
•    LAN and WAN network settings.
•    System time (NTP server) and time zone.
•    Scanning of network protocols and services.
•    Default scan actions when the unit detects threats.
•    Scan exceptions like the maximum file size.
•    Specify the notification server and notices for use in email notificatio\
ns.
•    Scan engine and signature updates.
3.    Click  Apply to save your changes.
The unit reboots. If your computer IP address is now on a different subn\
et, your 
computer loses its connection to the UTM. If so, restart the computer to\
 refresh 
its network settings.
Licenses
Your unit is bundled with three 30-day trial licenses.
•    Web scanning
•    Email scanning
•    Support and maintenance
Activating the licenses starts their term of use. Activate the licenses \
only when you  are ready to start using this unit. If your unit has never been register\
ed before, use 
the 30-day trial period for all 3 types of licenses to perform initial t\
esting and 
configuration. 
Note:  Be sure that the unit has Internet access before registering the license\
s.
•     Activate the trial licenses by selecting Support >  Registration and click the 
“Trial” button. Once you activate the trial licenses, you can then update t\
he 
unit with the latest UTM build and signature & engines during the 30-day\
 trial 
period.
•    If you purchase a license subscription bundled with your unit, a license\
 is  assigned to your unit’s serial number. When you register your unit, t\
he 
license key is automatically downloaded to your unit. Select Support > 
Registration, fill out the registration page, and click “Register” to activate 
the services. 
Note:  the 30-day trial licenses are revoked once you activate the purchased 
service license keys. The purchased service license keys offer one year \
or three 
years of service. 
See the reference manual for additional information about licenses.
Register and Activate the Licenses
Note:  Be sure that the unit has 
Internet access before registering 
the licenses.
1.    Log in to the unit. 
2.    Select  Support > Registration  
to display the Registration tab.
3.    Enter the customer information. If using the trial licenses, click  Trial. If you 
have purchased licenses, click  Register. The unit activates the licenses. After 
registration is complete the unit displays the license keys and their ex\
piration 
dates.
Online Documentation and Support
Select Support > Documentation 
to view the reference manual. 
Select  Support > Knowledge Base  
to view the support page, which 
includes this document and the 
reference manual. Go to 
http://www.netgear.com/support  and 
select your product model number.
Consult the reference manual for 
instructions for using the online support remote diagnostics.
Technical Support
After installing your device, locate the serial number on the label of y\
our product and  use it to register your product at https://my.netgear.com. 
You must register your product before you can use NETGEAR telephone supp\
ort. 
NETGEAR recommends registering your product through the NETGEAR website.\
 
For product updates and web support, visit 
http://support.netgear.com/general/contact/default.aspx.
You can get the user manual online at  http://downloadcenter.netgear.com or 
through a link in the product’s user interface.
UTM25S_IG_13Sept2012.fm  Page 2  Thursday, September 13, 2012  3:28 PM