Netgear Ex6150v2 Ac1200 Wifi Range Extender User Manual

							Get Started 11
 AC1200
 WiF  Range Extender
To use WPS to connect the extender to your WiFi router:
1. Press the WPS button on the extender.
The WPS LED 
 blinks.
2.  Within two minutes, press the WPS button on your router or access point.
The WPS LED on the extender lights solid green, the Router Link LED 
 lights, and 
the extender connects to your existing WiFi network.
If the Router Link LED does not light, try again. If it still does not l\
ight, see Connect With 
the NETGEAR Installation Assistant  on page
  12. 
3.  If your WiFi router supports the 5 GHz band, repeat Steps 1 and 2 to con\
nect the extender 
to the 5 GHz band.
4.  Unplug the extender and move it to a new location that is about halfway \
between your router 
and the area with a poor router WiFi signal.
The location that you choose must be within the range of your existing W\
iFi router  network.
DO DON’T
5. Plug the extender into an electrical outlet and wait for the Power LED  to light green.
6.  Use the Router Link LED 
 to help you choose a spot where the extender-to-router 
connection is optimal.
7.  If the Router Link LED doesn’t light amber or green, plug the extende\
r into an outlet closer 
to the router and try again.
Keep moving the extender to outlets closer to the router until the Route\
r Link LED lights 
amber or green.
8.  On your WiFi-enabled computer or mobile device, open the WiFi connection\
 manager and 
locate and connect to the new extender WiFi network.
The extender creates two new extender WiFi networks. The extender’s new WiFi network  names are based on your existing WiFi network name, with _2GEXT and _5GE\
XT at the 
ends of the names.
For example:
• Existing W
 iFi network name . MyNetworkName
• New extender W
 iFi network names. MyNetworkName_2GEXT and 
MyNetworkName_5GEXT
Use the same WiFi password that you use for your WiFi router. 
						

							Get Started 12
AC1200
 WiF  Range Extender 
9. Test the new extended WiFi range by moving your WiFi-enabled computer or \
mobile device 
to the area with a poor router WiFi signal:
a. Leave your WiFi-enabled computer or mobile device in the area with a poo\
r router 
WiFi signal and return to the extender

.
b.  Check the Client Link LED 
 on the extender:
• If the Client Link LED is solid green or amber
 , your extender WiFi network reaches 
the area with a poor router WiFi signal and your network setup is comple\
te.
• If the Client Link LED is red, your new extender WiFi network does not r\
each the 
area with a poor router WiFi signal.
You must move your WiFi-enabled computer or mobile device closer to the  extender until the Client Link LED turns solid green or amber
 .
Connect With the NETGEAR Installation Assistant
You can use a web browser to log in to the extender and set up its WiFi c\
onnection to your existing WiFi router.
To connect using the NETGEAR installation assistant:
1.  Connect your device to the extender using a wired Ethernet or WiFi conne\
ction:
• T
o connect with a wired Ethernet connection, use an Ethernet cable to con\
nect the 
Ethernet port on the extender to an Ethernet port on your computer.
• T
o connect with WiFi, on your WiFi-enabled computer or mobile device, ope\
n the WiFi 
connection manager and locate and connect to the extender NETGEAR_EXT (\
SSID) 
WiFi network.
After the connection with your WiFi-enabled computer or mobile device is\
 established, the  Client Link LED
  lights.
2.  Launch web browser
 .
3.  Enter  www
 .mywifiext.net in the address field of the browser.
The New Extender Setup page displays.
4.  Click the  NEW EXTENDER SETUP  button. 
						

							Get Started 13
 AC1200
 WiF  Range Extender
The first time that you log in to the extender, the Create Account page displays. If the 
Create Account page does not display, visit  www.mywifiext.net.
5. Complete the fields on the Create Account page and click the  NEXT button.
6.  V
erify that the  Access Point/Extender  switch is set to Extender  and click the 
CONTINUE  button.
7.  Select a WiFi network to extend and click the  NEXT button.
If you do not want to extend both WiFi bands, clear the 2.4 GHz W
 iFi Networks or the  
5 GHz WiFi Networks check box.
8.  In the Password (Network Key)  field, type the existing WiFi network password (also called 
passphrase or security key) and click the  NEXT button.
9.  Set the network name (SSID) and password for your new extender WiFi ne\
twork and click 
the  NEXT button.
Note: We recommend that you use a network name (SSID) for your extender 
that is different from the SSID that your router uses.
Wait for the page to display a list of new extender WiFi networks, which \
might take up to 
one minute.
10.  Connect your WiFi-enabled computer or mobile device to the new extender \
WiFi network 
using the extender SSID and password that you created in Step 9.
11.  Make sure that your WiFi-enabled computer or mobile device is successful\
ly connected 
before you click the  CONTINUE button.
12.  Click the  CONTINUE button.
A message displays confirming that the extender is connected to the new \
extender WiFi  network.
13.  Click the  NEXT button.
The registration page displays.
14.  Complete the registration fields and click the  FINISH button to complete the setup. 
						

							Get Started 14
AC1200
 WiF  Range Extender 
If you do not want to register your extender, click the Skip Registration link. Note that 
you must register your extender before you can use NETGEAR telephone sup\
port.
The Status page displays.
15.  Unplug the extender and move it to a new location about halfway between \
your router and 
the area with a poor WiFi signal.
The location that you choose must be within the range of your existing W\
iFi router  network.
DO DON’T
16. Plug the extender into an electrical outlet and wait for the Power LED  to light green. 
17.  Use the Router Link LED 
 to help you choose a spot where the extender-to-router 
connection is optimal.
18.  If the Router Link LED doesn’t light amber or green, plug the extende\
r into an outlet closer 
to the router and try again.
Keep moving the extender to outlets closer to the router until the Route\
r Link LED lights 
amber or green.
19.  Reconnect your WiFi-enabled computer or mobile device to the new extende\
r WiFi network.
20.  T
est the new extended WiFi range by moving your WiFi-enabled computer or \
mobile device 
to the area with a poor router WiFi signal:
a. Leave your WiFi-enabled computer or mobile device in the area with a poo\
r router 
WiFi signal and return to the extender

.
b.  Check the Client Link LED 
 on the extender:
• If the Client Link LED is solid green or amber
 , your new extender WiFi network 
reaches the area with a poor router WiFi signal and your network setup i\
s 
complete.
• If the Client Link LED is red, your new extender WiFi network does not r\
each the 
area with a poor router WiFi signal.
You must move your WiFi-enabled computer or mobile device closer to the  extender until the Client Link LED turns solid green or amber
 . 
						

							Get Started 15
 AC1200
 WiF  Range Extender
Connect an Ethernet-Enabled Device
After the extender is connected to your existing WiFi network, you can c\
onnect a wired 
device to the extender using an Ethernet cable. The device can then access your existing 
network through the extender’s WiFi connection.
Figure 4. Connect a device to the Ethernet LAN port
Use the Extender in Access Point Mode
You can use the extender as a WiFi access point, which creates a new WiFi\
 hotspot by using a wired Ethernet connection.
Figure 5. Extender in access point mode

To use the extender in access point mode:
1.  Set the  Access Point/Extender  switch to Access Point .
2.  Plug the extender into an electrical outlet and wait for the Power LED 
 to light green.
If the Power LED does not light, press the  Power On/Off button on the side of the 
extender
 .
3.  Use an Ethernet cable to connect the Ethernet port on the extender to a \
router Ethernet LAN 
port or a remote Ethernet LAN jack with LAN access.
The extender joins the LAN and creates a WiFi hotspot. 
						

							Get Started 16
AC1200
 WiF  Range Extender 
4. On your WiFi-enabled computer or mobile device, open the WiFi connection\
 manager and 
locate and connect to one of the following WiFi extender networks:
• 2.4 GHz network. NETGEAR_EXT
• 5 GHz network. NETGEAR_5GEXT
When you join the network, the extender Client Link LED 
 lights to show that you are 
connected.
5.  Launch a web browser and enter  www
 .mywifiext.net in the address field.
The New Extender Setup page displays.
6.  Click the  NEW EXTENDER SETUP  button.
If the Create Account page does not display, visit  www.mywifiext.net.
7.  Complete the fields on the Create 
 Account page and click the NEXT button.
8.  When prompted, set the network name (SSID), security option, and passw\
ord for each 
access point network and click the  NEXT button.
Your settings are applied and the extender is ready to be used as an acce\
ss point.
9.  Connect your WiFi-enabled computer or mobile device to the new access po\
int WiFi network 
using the SSID and password that you created in Step 8.
10.  Click the  CONTINUE button.
A page displays that says you successfully created an access point.
11.  Click the  NEXT button.
The registration page displays.
12.  Follow the onscreen instructions to register your extender
 . 
						

							Get Started 17
 AC1200
 WiF  Range Extender
Access Extender Settings
After installation, you can log in to the extender to view or change the\
 extender’s settings.
To log in to the extender:
1. On your WiFi-enabled computer or mobile device, open the WiFi connection\
 manager 
and locate and connect to a new extender WiFi network.
After the connection with the WiFi-enabled computer or mobile device is \
established, the  Client Link LED
  lights.
2.  Launch a web browser
 .
3.  Enter  www
 .mywifiext.net in the address field of the browser.
A login page displays.
4.  Enter your email address and password and click the  LOG IN button.
The Status page displays.
Run Smart Setup
You can use Smart Setup to change the extender settings. This is an easy way to connect the  extender to a different router or to change the extender WiFi network name (SSID) or Wi\
Fi 
password.
To run Smart Setup:
1.  On your WiFi-enabled computer or mobile device, open the WiFi connection\
 manager 
and locate and connect to a new extender WiFi network.
After the connection with the WiFi-enabled computer or mobile device is \
established, the  Client Link LED
  lights.
2.  Launch a web browser
 .
3.  Enter  www
 .mywifiext.net in the address field of the browser.
A login page displays.
4.  Enter your email address and password and click the  LOG IN button.
The Status page displays.
5.  Click the  SMART SETUP  button.
The Welcome page displays.
6.  Click the  WIFI RANGE EXTENDER  button.
The extender scans for WiFi signals and finds the WiFi networks in your \
area and  displays a list.
7.  Select your WiFi network and click the NEXT button. 
						

							Get Started 
18 AC1200 WiF Range Extender 
8. When prompted, enter the password to connect to your WiFi network and click the NEXT 
button.
A message displays when the extender connects to your existing router’s WiFi network.
9. Click the NEXT button.
The extender applies your settings to its WiFi network names and WiFi passwords. 
During this change, the extender disconnects you from its WiFi network. 
10. When prompted, connect your WiFi-enabled computer or mobile device to the extender WiFi 
network and click the CONTINUE button.
The registration page displays.
11. Complete the registration fields and click the FINISH button to complete the setup.
If you do not want to register your extender, click the Skip Registration link. Note that 
you must register your extender before you can use NETGEAR telephone support.
The Status page displays. 
						

							19
3
3.   Extender Network Settings
This chapter covers the following topics: 
•View Connected Devices 
•Boost Your Video Streaming With FastLane Technology 
•Adjust the WiFi Coverage 
•View WiFi Settings 
•Change the WiFi Network Name 
•Turn Off the SSID Broadcast to Create a Hidden Network 
•Disable or Enable the WiFi Radios 
•Change the WiFi Speed 
•Use WPS to Add a Computer to the Extender’s WiFi Network 
•Deny Access to a WiFi Device 
•Set Up an Access Schedule 
•Change the Extender’s Device Name 
•Set Up the Extender to Use a Static IP Address 
•Use the Extender With MAC Filtering or Access Control  
						

							Extender Network Settings 20
AC1200
 WiF  Range Extender 
View Connected Devices
You can view a list of devices that are connected to the extender network\
.
To view connected devices:
1. On your WiFi-enabled computer or mobile device, open the WiFi connection\
 manager 
and locate and connect to the extender WiFi network. 
2.  Launch a web browser
 . 
3.  Enter  www
 .mywifiext.net in the address field of the browser.
A login window opens.
4.  Enter your user name and password.
The Status page displays. 
5.  Select  Settings > Connected Devices .
Boost Your Video Streaming With FastLane Technology
Get the most out of your HD entertainment with FastLane technology. With FastLane 
technology, the extender connects to your router using one band and connects to yo\
ur 
WiFi-enabled devices using another band. Because a band is dedicated to \
each function, 
performance is enhanced.
If all your WiFi-enabled devices and your WiFi router support only the 2\
.4 GHz band, or all 
your WiFi-enabled devices and your WiFi router support only the 5 GHz ba\
nd, do not enable 
FastLane T

echnology.