NEC Xl 6500 Projector User Manual

							51
Enables you to adjust the brightness of the lamp.
Items to select
¥ Normal ---------------- Normally select this mode.
¥ High Bright ----------- Select this mode to increase the brightness
of the lamp.
NOTE: The High Bright mode shortens the lamp life. Be sure to use
this mode at temperature 95° F (35° C) or less.
Lamp Mode
Lamp Power
Normal
High-Bright
3.OPERATION 
						

							52 3.OPERATION
Set Option
 Passcode
n Entering Passcode
To prevent any unauthorized operation or mis-adjustment, the
projector is equipped with a passcode option. If your passcode has
not been entered correctly, the ÒAdjustmentÓ  menu will not be
displayed. When the ADJUST button is pressed, and no passcode has
been entered, the ÒPasscode?Ó screen is displayed. Enter your
passcode.
To do this, proceed as follows:
1Press the ADJUST button.
¥  The ÒPasscode?Ó screen is displayed.
2Enter the four digit passcode you have already registered by
using the Ò1Ó through Ò10Ó buttons.
1) Each time you press the INPUT button, an asterisk appears
under the ÒPasscode?Ó message.
2) After you have finished entering the four digit passcode, press
ENTER.
NOTE: If you have made an error, press the NORMAL button to
delete the asterisk Ò*Ó. Then re-enter the correct passcode. To
delete all the entered digits, hold down the CTL button then
press the NORMAL button.
3) If the entered passcode is correct, the ÒADJUSTÓ menu is
displayed.
NOTE: If the passcode is not correct, the ÒWarning Different
Passcode!!Ó message is displayed and you are required to enter
the correct passcode.
3Proceed to each adjustment and setting.
Passcode?
**** 
						

							53
n Registering Passcode
When the projector is shipped from the factory, no passcode is
registered. If you want to use the passcode option, you must register
a passcode.
To register a new passcode, proceed as follows:
1Press the ADJUST button.
¥ The ÒAdjustmentÓ menu will be displayed.
2Use the CURSOR 
or button to highlight the Ò8.Set OptionÓ
menu. Press ENTER to display the Set Option menu.
3Use the CURSOR 
or button to highlight the Ò1.PasscodeÓ
line. Press ENTER to display the ÒPasscode SettingÓ menu.
4Use the CURSOR 
or button to select ÒEntryÓ. Press
ENTER to display the ÒNew Passcode?Ó menu.
5Enter a four digit passcode using the Ò1Ó through Ò10Ó buttons.
1) Each time you press the INPUT button, an asterisk will appear
next to the ÒNew Passcode?Ó message.
NOTE: Ò0000Ó and Ò9999Ó cannot be used as a passcode.
2) Once you have finished entering your four digit passcode,
press ENTER to store the code.
NOTE: If you have made an error, press the NORMAL button
to delete the asterisk Ò[Ó. Then re-enter the correct passcode.
To delete all the entered digits, hold down the CTL button
then press the NORMAL button.
3) If the passcode has been entered correctly, the ÒConfirm New
Passcode?Ó menu will be displayed.
NOTE: If the passcode is not entered correctly, the ÒWarning
Passcode!!Ó message will be displayed. You will be required
to enter the passcode correctly.
-Adjustment-
1. Source Registry
2. Amplitude
3. White Balance
4. Signal Level
5. Uniformity
6. Display Function
7. Lamp Mode
8. Set Option
-Set Option-
1. Passcode
2. Setting Mode
3. Menu Mode
4. Execute Mode
PasscodePasscode Setting
Entry   Disable
Passcode
PASSCODE SETTING
 ENABLE    DISABLE
Passcode Setting
New Passcode [       ]
SSSS
3.OPERATION 
						

							54 3.OPERATION
6Enter the new passcode again.
1) Each time you press the INPUT button, an asterisk will appear
next to the ÒConfirm New Passcode?Ó message.
2) Once you have finished entering the new four digit passcode,
press ENTER.
NOTE: If you have made an error, press the NORMAL button
to delete the asterisk Ò*Ó. Then re-enter the correct passcode.
To delete all the entered digits, hold down the CTL button
then press the NORMAL button.
3) If the entered passcode is correct, the ÒChange Passcode
Complete!!Ó message will be displayed.
NOTE: If the passcode is not correct, the ÒWarning Different
Passcode!!Ómessage will be displayed. You are required to
enter the new passcode correctly.
The new passcode has been registered.
Passcode
PASSCODE SETTING
 ENABLE    DISABLE
Passcode Setting
Confirm Passcode [       ]
SSSS 
						

							55
n Changing Your Passcode
To change your passcode, proceed as follows:
1Press the ADJUST button.
¥ The ÒPasscode?Ó screen will be displayed.
2Enter the four digit current passcode using the Ò1Ó through Ò10Ó
buttons. Press ENTER.
¥ The ÒAdjustmentÓ menu will be displayed.
3Use the CURSOR 
or button to highlight the Ò8. Set
OptionÓ menu. Press ENTER to display the ÒSet OptionÓ menu.
4Use the CURSOR 
or button to select Ò1. PasscodeÓ. Press
ENTER to display the ÒPasscode SettingÓ menu.
5Use the CURSOR 
or button to select ÒEntryÓ.
PressENTER to display the ÒCurrent Passcode?Ó menu.
6Enter the four digit passcode (the current passcode) using the Ò1Ó
through Ò10Ó buttons.
1) Each time you press the INPUT button, an asterisk will
appear next to the ÒCurrent Passcode?Ó message.
2) Once you have finished entering the four digit passcode, press
ENTER.
NOTE: If you have made an error, press the NORMAL button
todelete the asterisk Ò*Ó. Then re-enter the correct passcode.
To delete all the entered digits, hold down the CTL button
then press the NORMAL button.
3) If the entered passcode is correct, the ÒNew Passcode?Ó
screen will be displayed.
NOTE: If the passcode is not correct, the ÒWarning
Different Passcode!!Ó message is displayed. You will be
required to enter the correct current passcode.
-Adjustment-
1. Source Registry
2. Amplitude
3. White Balance
4. Signal Level
5. Uniformity
6. Display Function
7. Lamp Mode
8. Set Option
-Set Option-
1. Passcode
2. Setting Mode
3. Menu Mode
4. Execute Mode
PasscodePasscode Setting
Entry   Disable
Passcode
Passcode Setting
Current Passcode [       ]
SSSS
Passcode
PASSCODE SETTING
 ENABLE    DISABLE
Passcode Setting
New Passcode [       ]
SSSS
3.OPERATION 
						

							56 3.OPERATION
7Enter a new passcode using the Ò1Ó through Ò10Ó buttons.
1) Each time you press the INPUT button, an asterisk will appear
next to the ÒNew Passcode?Ó message.
2) Once you have finished entering the four digit new passcode,
press ENTER.
NOTE: If you have made an error, press the NORMAL button
to delete the asterisk Ò*Ó. Then re-enter the correct passcode.
To delete all the entered digits, hold down the CTL button
thenpress the NORMAL button.
3) If the passcode has been entered correctly, the ÒConfirm New
Passcode?Ó menu will be displayed.
NOTE: If the passcode is not entered correctly, the ÒWarning
Different Passcode!!Ó message will be displayed. You are
required to enter the new passcode correctly.
8Enter the new passcode again using the Ò1Ó through Ò10Ó buttons.
1) Each time you press the INPUT button, an asterisk will appear
under the ÒConfirm New Passcode?Ó message.
2) Once you have finished entering the four digit new passcode,
press ENTER.
NOTE: If you have made an error, press the NORMAL button
to delete the asterisk Ò*Ó. Then re-enter the correct passcode.
To delete all the entered digits, hold down the CTL button
then press the NORMAL button.
3) If the entered passcode is correct, the ÒChange Passcode
Complete!!Ó message is displayed.
NOTE: If the passcode is not entered correctly, the ÒWarning
Different Passcode!!Ó message is displayed. You will be
required to enter the new passcode correctly.
The passcode has been changed to another.
Passcode
PASSCODE SETTING
 ENABLE    DISABLE
Passcode Setting
Confirm Passcode [       ]
SSSS 
						

							57
-Adjustment-
1. Source Registry
2. Amplitude
3. White Balance
4. Signal Level
5. Uniformity
6. Display Function
7. Lamp Mode
8. Set Option
-Set Option-
1. Passcode
2. Setting Mode
3. Menu Mode
4. Execute Mode
Passcode
Passcode Setting
Current Passcode [       ]
SSSS
n Canceling Your Passcode
To cancel the passcode, proceed as follows:
1Press the ADJUST button and then enter your passcode.
¥ The ÒPasscode?Ó screen will be displayed.
2Enter the four digit current passcode using the Ò1Ó through Ò10Ó
buttons and then press ENTER.
¥ The ÒAdjustmentÓ menu will be displayed.
3Use the CURSOR 
or button to highlight Ò8. Set OptionÓ.
Press the ENTER button to display the ÒSet OptionÓ menu.
4Use the CURSOR 
or button to highlight Ò1. PasscodeÓ
line. Press ENTER to display the ÒPasscode SettingÓ menu.
5Use the CURSOR 
or button to select ÒDisableÓ. Press
ENTER to display the ÒPasscode Disable?Ó menu.  Select ÒYesÓ
and press ENTER.
¥ The ÒCurrent PasscodeÓ screen will be displayed.
6Enter the four digit passcode (the current passcode) using the Ò1Ó
through Ò10Ó buttons.
1) Each time you press the INPUT button, an asterisk will appear
next to the ÒCurrent Passcode?Ó message.
2) Once you have finished entering the four digit passcode, press
ENTER.
NOTE: If you have made an error, press the NORMAL button
to delete the asterisk Ò*Ó. Then re-enter the correct passcode.
To delete all the entered digits, hold down the CTL button
then press the NORMAL button.
3) If the entered passcode is correct, the ÒPasscode Disable?Ó
menu will be displayed.
NOTE: If the passcode is not correct, the ÒWarning Different
Passcode!!Ó message will be displayed. You will be required
to enter your correct passcode.
Passcode
PASSCODE SETTING
 ENABLE    DISABLE
Passcode Setting
Passcode Disable ?
Yes No
PasscodePasscode Setting
Entry   Disable
3.OPERATION 
						

							58 3.OPERATION
7Use the CURSOR 
or button to select Yes and then press
ENTER.
Items to select
¥ Yes ---------------- When selecting ÒYesÓ, the current passcode
will be canceled. You will not be required to
re-enter your passcode when you press the
ADJUST button to re-enter the ADJUST
mode.
¥ No ----------------- When selecting ÒNoÓ, the current passcode
will remain in effect.
Your passcode has been cancelled. 
						

							59
Setting Mode
Enables you to set various items.
To do, follow the steps below.
1. Press the ADJUST button to display the Adjustment menu.
2. Use the CURSOR 
or button to select Ò8. Set OptionÓ menu.
Press ENTER.
3. Use the CURSOR 
or button to select Ò2. Setting ModeÓ
menu. Press ENTER.
Proceed to the following steps.
n PJ Orientation
This feature allows you to set the installation type according to the
projection configuration.
1Use the CURSOR
orbutton to select the ÒPJ ORIENTA-
TIONÓ item, then press ENTER to display the ÒPJ ORIENTA-
TIONÓ menu.
-Setting Mode-
1. PJ Orientation
2. Default Source Select
3. S-Video Mode Select
4. Video System Select
5. Auto Data Store
6. Option Terminal Speed
7. Uniformity Switching
Setting Mode
PJ Orientation
Default Mode Select
S-Video Mode Select
Video System Select
Auto Data Store
Option Terminal Speed[Ceiling/Front    ]
[S2              ]
[Disable        ]
[38400 BPS    ]
[Disable        ]
[Disable        ]Manual
  NTSC3.58 Default
  INPUT-A
  S-Video
Uniformity White
               Edge Blend.
2Use the CURSORorbutton to select one of the four
projector installation types and press ENTER.
Items to select
¥ CEILING/REAR .... Ceiling mounting type and rear projection
¥ FLOOR/REAR ....... Desk top type and rear projection
¥ CEILING/FRONT .. Ceiling mounting type and front projection
¥ FLOOR/FRONT ..... Desk top type and front projection
Floor / Rear
Ceiling / Front
Floor / Front
Ceiling / Rear
3.OPERATION 
						

							60 3.OPERATION
n Default Source Select
-Setting Mode-
1. PJ Orientation
2. Default Source Select
3. S-Video Mode Select
4. Video System Select
5. Auto Data Store
6. Option Terminal Speed
7. Uniformity Switching
Setting Mode
PJ Orientation
Default Mode Select
S-Video Mode Select
Video System Select
Auto Data Store
Option Terminal Speed[Ceiling/Front    ]
[S2              ]
[Disable        ]
[38400 BPS    ]
[Disable        ]
[Disable        ]Manual
  NTSC3.58 Default
  INPUT-A
  S-Video
Uniformity White
               Edge Blend.
Setting Mode
PjORIENTATION
DefaultULT MODE SELECT
S-VIDEO MODE SELECT
VidEO SYSTEM SELECT
Auto Data Store
Option Terminal Speed[CEILING/FRONT  ]
[?????????CD) 
[Default        ]
[38400 Bps     ]MANUAL
  NTSC3.58 DEFAULT
  INPUT-A
  S-VIDEO
Default Source Select
Default Source
Slot
Signal
OK [Default  ]
[Input-A    ]
[COMPO. HDTV)  ]
Cancel
You can set the projector to default to any one of its inputs each time
the projector is turned on.
Proceed as follows:
1Use the CURSOR
orbutton to select the ÒDefault Source
SelectÓ item, then press ENTER to display the ÒDefault Source
SelectÓ menu.
2Use the CURSOR
orbutton to select either ÒDefaultÓ or
ÒLastÓ and press ENTER.
¥ Selecting ÒLASTÓ completes setting.
¥ Selecting ÒDEFAULTÓ displays the ÒDefault inputÓ screen.
Items to select
¥ DEFAULT . Displays the same source input every time the
projector is started up.
¥ LAST ....... Sets the projector to default to the previous last
active input each time the projector is turned on.
Note: An input must be active for a minimum of 10
minutes before it is recognized as the last active
signal.