NEC Wt610e Projector User Manual

24
2. Installation and Connections
AUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO VIDEO
PC CARD
AUDIO IN
RL
/MONOVIDEO INS-VIDEO IN DVI-I IN
COMPUTER IN MONITOR OUTDVI-I COMPUTERAUDIO IN AUDIO OUT PC CONTROL
REMOTE
INUSBAUDIO INVIDEO INS-VIDEO IN
Connecting Your VCR or Laser Disc Player
Audio equipment S-video cable (not supplied) Video cable (not supplied)
Audio cable (not supplied)
VCR/ Laser disc player
Use common RCA cables (not provided) to connect your VCR, laser disc player or document camera to your...

25
PC CARD
AUDIO IN
RL
/MONOVIDEO INS-VIDEO IN DVI-I IN
COMPUTER IN MONITOR OUTDVI-I COMPUTERAUDIO IN AUDIO OUT PC CONTROL
REMOTE
INUSB
Connecting to a Network
The WT615/WT610 comes standard with a PC Card slot which accepts a wired and wireless LAN card. Placing the
optional wireless LAN card (NWL-100A/E) in the PC card slot of the projector provides a wireless LAN connection. To
use a LAN connection, you are required to assign an IP address to the projector. For setting the LAN mode, see page
111 (From...

26
(B) Example of wireless LAN connection
(Network Type → Mode: Infrastructure)
2. Installation and Connections
Access PointWired LAN
To make connection with a wired LAN via an access point, you need to select the Infrastructure mode.
From the menu, select [Setup] → [Installation] → [LAN Mode] → “Profile” → “Advanced” → “Network Type” →“Mode”
→  “Infrastructure”.
(C) Example of wireless LAN connection (Network Type → Mode: 802.11 Ad Hoc)
To enable direct communication (i.e., peer-to-peer) between...

27
2. Installation and Connections
Inserting the PC Card
1. Turn off the main power switch before inserting the
PC card. (This step is needed only when the LAN
card being inserted into the projectors PC CARD
slot)
2. Hold the PC card horizontally and insert it slowly into
the PC card slot with its top facing up.
The eject button pops out once the PC card is fully inserted.
Check that the PC card is fully inserted.
NOTE: Do not try to force the PC card into the slot or you may bend
the pins inside the...

28
2. Installation and Connections
PC Card Type
The PC Card slot accepts PCMCIA Type II only.
NOTE: The projector does not support NTFS formatted flash memory card.
Be sure to use a flash memory card formatted with the FAT32, FAT16 or FAT file system.
To format your flash memory card in your computer, refer to the document or help file that comes with your Windows operating
systems. 

29
2. Installation and Connections
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cables three-pin plug to the AC IN of the projector, and then connect the other plug
of the supplied power cable in the wall outlet.
Make sure that the prongs are fully inserted
into both the AC IN and the wall outlet.
← To wall outlet
CAUTION:
Do not unplug the power cable from the wall outlet under any one of the following circumstances.
Doing so can...

30
3
Projecting an Image
(Basic Operation)
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

 Turning on the Projector ............................................. 31
 Adjusting the Position and Size of the Projected Image
(Focus Adjustments) .............................................. 33
 Selecting a Source .................................................... 40
 Optimizing an RGB Image Automatically ................... 41
 Turning Up or Down Volume ...................................... 41
 Adjusting...

31
POINTERLASER
MAGNIFYPAGE OFF
POWERON
ENTER
MENU
EXIT
R-CLICK
UP
DOWN
POWER ENTER EXIT
STATUS
LAMP     ON/
STAND BYAUTO
ADJUST3D
REFORM
3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.

 Turning on the Projector
NOTE:
•The projector has two power switches: a main power switch and a POWER (ON/STAND BY) button (POWER ON and OFF on the
remote control).
•When plugging in or unplugging the supplied power cable, make sure...

32
POWER ENTERSELECT
EXIT
STATUS
LAMP     ON/
STAND BYAUTO
ADJUST3D
REFORM
POINTERLASER
MAGNIFYPAGE OFF
POWERON
ENTER
MENU
EXIT
R-CLICK
UP
DOWN
POWER ENTER EXIT
STATUS
LAMP     ON/
STAND BYAUTO
ADJUST3D
REFORM
SELECT
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the 21 menu languages.
To select a menu language, follow these steps:
1. Use...

33
3. Projecting an Image (Basic Operation)
90˚
1. Check whether the screen is set up to be vertical by viewing it from
the side.
 Adjusting the Position and Size of the Projected Image
   (Focus Adjustments)
•After turning on the power, projected images may flicker for 3 to 5 minutes until the lamp lighting is stabilized.
Also after turning on the projector, the picture position may be slightly changed.
Wait 10 minutes until the light status and projected images become stable.
•If the screen is tilted...