NEC Vt650 Projector User Manual
Have a look at the manual NEC Vt650 Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 42
E–36
[Page 4] (Advanced mode)
Setup
Page1 Page2 Page3 Page4
Default Source Select
Communication SpeedSelect
19200bps
Control Panel Key LockClear Lamp Hour MeterClear Filter Usage
Default Source RGB
Unlock
[Page 3] (Advanced mode)
Setup
Page1 Page2 Page3 Page4
Auto Adjust
Auto Start
Power Management
Keystone Save
On Off
On Off
On OffPower Off ConfirmationOn OffOn Off
When “Auto Adjust” is set to “On”, the projector automati-
cally determines the best resolution for the current RGB in-
put signal to...](http://img.usermanuals.tech/thumb/54/92450/w64_nec-vt650-manual_d-41.png "Page 42
E–36
[Page 4] (Advanced mode)
Setup
Page1 Page2 Page3 Page4
Default Source Select
Communication SpeedSelect
19200bps
Control Panel Key LockClear Lamp Hour MeterClear Filter Usage
Default Source RGB
Unlock
[Page 3] (Advanced mode)
Setup
Page1 Page2 Page3 Page4
Auto Adjust
Auto Start
Power Management
Keystone Save
On Off
On Off
On OffPower Off ConfirmationOn OffOn Off
When “Auto Adjust” is set to “On”, the projector automati-
cally determines the best resolution for the current RGB in-
put signal to...")
![Page 44
E–38
MENU
ENTERCANCELSELECT
POWER STATUS
ON/OFFSOURCE
AUTO ADJUST1
5. After you install a new lamp, select [Advanced Menu] →
[Projector Options]→[Setup]→[Page 4]→[Clear Lamp Hour
Meter] to reset the lamp usage hours.
NOTE: When the lamp exceeds 2100 hours (up to 3100 hours in
Eco mode) of service, the projector cannot turn on and the menu
is not displayed. If this happens, press the Help button on the
remote control for a minimum of 10 seconds while in standby
mode. When the lamp time clock is reset to...](http://img.usermanuals.tech/thumb/54/92450/w64_nec-vt650-manual_d-43.png "Page 44
E–38
MENU
ENTERCANCELSELECT
POWER STATUS
ON/OFFSOURCE
AUTO ADJUST1
5. After you install a new lamp, select [Advanced Menu] →
[Projector Options]→[Setup]→[Page 4]→[Clear Lamp Hour
Meter] to reset the lamp usage hours.
NOTE: When the lamp exceeds 2100 hours (up to 3100 hours in
Eco mode) of service, the projector cannot turn on and the menu
is not displayed. If this happens, press the Help button on the
remote control for a minimum of 10 seconds while in standby
mode. When the lamp time clock is reset to...")
E–45 Cable Connection Communication Protocol Baud rate: 19200 bps Data length: 8 bits Parity: No parity Stop bit: One bit X on/off: None CommunicationsFull duplex procedure: 1 2 54 36 7 8 To RxD of PCPC Control Connector (DIN-8P) To TxD of PCTo GND of PC NOTE: Pins 2, 3, 5, 6 and 8 are used inside the projector. PC Control Codes Function Code Data POWER ON 02H 00H 00H 00H 00H 02H POWER OFF 02H 01H 00H 00H 00H 03H INPUT SELECT RGB 02H 03H 00H 00H 02H 01H 01H 09H INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H PICTURE MUTE ON 02H 10H 00H 00H 00H 12H PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H SOUND MUTE ON 02H 12H 00H 00H 00H 14H SOUND MUTE OFF 02H 13H 00H 00H 00H 15H NOTE: Contact your local dealer for a full list of the PC Con- trol Codes if needed.