NEC Vt465 Projector User Manual

							E-9
Part Names of the Remote Control
NOTE: If you are using a Macintosh computer, you can click either the CANCEL(right-click) or ENTER (left-click) button to activate the mouse.
1. Infrared Transmitter
Direct the remote control toward the remote sensor on the projector
cabinet.
2. LED Flashes when any button is pressed.
3. POWER ON Button When the main power is on, you can use this button to turn your
projector on.
NOTE:  To turn on the projector, press and hold the POWER ON button for aminimum of two seconds.
4. POWER OFF Button
You can use this button to turn your projector off.
NOTE:  To turn off the projector, press the POWER OFF button twice.
5. VIDEO Button
Press this button to select a video source from a VCR, DVD player,
laser disc player or document camera.
6. S-VIDEO Button Press this button to select an S-Video source from a VCR.
7. RGB Button Press this button to select RGB input.
8. AUTO ADJ.  Button Use this button to adjust an RGB source for an optimal picture.
See page E-20. 9. MENU Button
Displays the menu for various settings and adjustments.
10. SELECT  GHFE (Mouse) Button
When you are in the Computer mode, these buttons work as a com-
puter mouse.
When you are in the Projector mode, which is indicated by lighting
the PJ button. See page E-21.
GH  : Use these buttons to select the menu of the item you wish
to adjust.
FE  : Use these buttons to change the level of a selected menu
item. A press of the  E button executes the selection. When
no menus appear, these buttons work as a volume control.
When an image is magnified, the SELECT  GHFE button moves the
image.
1 1. ENTER (Left Click) Button
When you are in the Computer mode, this button works as the mouse
left button. When this button is pressed and held for a minimum of 2
seconds, the drag mode is set. When you are in the Projector mode,
which is indicated by lighting the PJ button: Use this button to enter
your menu selection. It works the same way as the ENTER button on
the cabinet. See page E-7.
12. CANCEL (Right Click) Button When you are in the Computer mode, this button works as the mouse
right button. When you are in the Projector mode, which is indicated
by lighting the PJ button: It works the same way as the CANCEL
button on the cabinet. See page E-7.
13. PJ Button Press this button to switch the SELECT, CANCEL, and ENTER but-
tons between the Projector mode (lit red) and the Computer mode.
Press this button or any one of the POWER ON/OFF, MENU, AS-
PECT, HELP, MAGNIFY, buttons to switch to the Projector mode and
the PJ button lights red. To switch back to the Computer mode, press
the PJ button again. See page E-21.
14. PICTURE Button Press this button to display the Picture adjustement screen such as
Brightness, Contrast, Sharpness, Color and Hue. See page E-26.
15. ASPECT  Button Press this button to display the Aspect Ratio select screen. See page
E-27.
16. HELP Button Provides the set information.
17. FREEZE Button This button will freeze a picture. Press again to resume motion.
18. PIC-MUTE Button This button turns off the image and sound for a short period of time.
Press again to restore the image and sound.
19. MAGNIFY (+)(–) Button Use this button to adjust the image size up to 400%.
The image is magnified about the center of the screen. See page E-
22.
20. VOLUME (+)(–) Button Press (+) to increase the volume and (–) to decrease it.
NOTE:  The default is the Computer mode, which allows you to use the SELECT,
CANCEL, and ENTER buttons as your computer mouse. When the POWER ON/ OFF, MENU, ASPECT, HELP, or MAGNIFY button is pressed, the PJ button lights
red to indicate that you are in the Projector mode. If no buttons are pr\
essed
within 60 seconds, the light goes out and the Projector mode is canceled\
.
OFFON
VIDEOS-VIDEORGB
PJ
MAGNIFY
SELECT
EMNU
TERNENCEACL
1
3
4
5
8
7
11
16 9
10
19 12
13
6
2
18
17
20
AUTO ADJ.
FREEZEPIC-MUTE
PICTURE1514
VOLUME
HELP
ASPECT
POWER 
						

							E-10
Battery Installation
1. Press firmly and slide the battery cover off.2. Remove both old batteries and install new ones (AA). Ensure thatyou have the batteries polarity (+/-) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place. Do not\
mix different types of batteries or new and old batteries.
Note on Remote Control Operation:
If you press and hold the SELECT  GHFE button while installing new
batteries, the remote control may fail to work properly.
Should this happen, remove the batteries and then install them again
without touching the SELECT button.
Remote Control Precautions
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
•A void excessive heat and humidity.
• If you will not be using the remote control for a long time, remove the
batteries.
• Do not place the batteries upside down.
• Do not use new and old batteries together, or use different types of
batteries together.
Operating Range for Wireless Remote Control
Remote control
•The infrared signal operates by line-of-sight up to a distance of about
22 feet/7 m and within a 60-degree angle of the remote sensor on the
projector cabinet.
• The projector will not respond if there are objects between the re-
mote control and the sensor, or if strong light falls on the sensor.
Weak batteries will also prevent the remote control from properly
operating the projector.
Remote sensor on projector cabinet
7m/22 feet
30˚
30˚
7m/22 feet
30˚
30˚ 
						

							E-11
3
1
2
INSTALLATION AND CONNECTIONS
This section describes how to set up your projector and how to connect v\
ideo and audio sources.
To the wall outlet.
Setting Up the Screen and the Projector
Selecting a Location
The further your projector is from the screen or wall, the larger the im\
age. The minimum size the image can be is approximately  21 (0.53 m)
measured diagonally when the projector is roughly 27.6 inches (0.7 m) from the wall or screen. The largest the image can be is 3 00 (7.6 m) when
the projector is about 393.7 inches (10 m) from the wall or screen. Use the drawing below as a guide. Y
our projector is simple to set up and use.
But before you get started, you must first:
1
Set up a screen and the projector.
2Connect your computer or video equip- ment to the projector. See page
E-13 – 16.
3Connect the supplied power cable. Seepage E-16.
NOTE:  Ensure that the power cable and any
other cables are disconnected before moving the projector. When moving the projector or
when it is not in use, cover the lens with the
lens cap.
300
240
406.4(W)X304.8(H)/160(W)X120(H)
365.8(W)X274.3(H)/144(W)X108(H)
304.8(W)X228.6(H)/120(W)X90(H)
243.8(W)X182.9(H)/96(W)X72(H)
203.2(W)X152.4(H)/80(W)X60(H)
162.6(W)X121.9(H)/64(W)X48(H)
121.9(W)X91.4(H)/48(W)X36(H)
81.3(W)X61.0(H)/32(W)X24(H)
61.0(W)X45.7(H)/24(W)X18(H)
50.8(W)X38.1(H)/20(W)X15(H)
42.7(W)X32(H)/17(W)X13(H)
Lens center
Screen Size
1.3/51.22.0/78.72.7/106.33.4/133.9
4.0/157.5
5.1/200.8 6.1/240.2
8.1/318.91.0/39.4
200
180
150
120
100
80
60
40
302521
609.6(W)X457.2(H)/240(W)X180(H)Screen size (Unit: cm/inch)
487.7(W)X365.8(H)/192(W)X144(H)
6.7/263.8
Distance (Unit: m/inch)
10.1/397.6
0.7/27.6 0.8/31.5 
						

							E-12
NOTE: Distances may vary +/-5%.
Distance Chart
B = Vertical distance between lens center and screen center
C = Throw distance
D = Vertical distance between lens center and top of screen (bottom of
screen for desktop)
α = Throw angle
Lens Center
Throw Angle ( α)
Throw Distance  (
C )
Screen center
Screen Diagonal
Screen Width
Screen Height Screen Bottom
(D )
(
B )
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and s\
creen. Refer to the table to determine the position of 
installation.
α
Wide – Tele
Screen Size B C
Wide – TeleDiagonal Width Heightdegree
––– - 10.0
11.8 - 9.9
11.7 - 9.8
11.6 - 9.7
11.5 - 9.6
11.4 - 9.6
11.4 - 9.6
11.4 - 9.6
11.4 - 9.5
11.4 - 9.5
11.4 - 9.5
11.4 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5 α
Wide – Tele
Screen Size B C
Wide – TeleDiagonal Width Heightdegree
––– - 10.0
11.8 - 9.9
11.7 - 9.8
11.6 - 9.7
11.5 - 9.6
11.4 - 9.6
11.4 - 9.6
11.4 - 9.6
11.4 - 9.5
11.4 - 9.5
11.4 - 9.5
11.4 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
D
D
inch
13
15
18
24
36
43
48
50
54
60
72
90
108
120
126
144
162
180 inch
––– - 29 29 - 35
35 - 42
47 - 57
71 - 86
86 - 103
96 - 115
101 - 121
108 - 129
120 - 144
144 - 173
181 - 217
217 - 260
241 - 290
253 - 304
290 - 348
326 - 391
363 - 400
inch
5
6
7
10
15
17
19
20
22
24
29
36
44
48
51
58
65
73 mm
320
381
457
610
914
1097
1219
1280
1372
1524
1829
2286
2743
3048
3200
3658
4115
4572 mm
––– - 740
740 - 880
890 - 1070
1200 - 1440
1810 - 2180
2180 - 2620
2430 - 2920
2550 - 3060
2740 - 3290
3050 - 3660
3660 - 4400
4590 - 5510
5510 - 6610
6130 - 7350
6440 - 7720
7360 - 8830
8290 - 9940
9210 -11050
mm
130
150
180
250
370
440
490
520
550
610
740
920
1110
1230
1290
1470
1660
1840
mm
533
635
762
1016
1524
1829
2032
2134
2286
2540
3048
3810
4572
5080
5334
6096
6858
7620 mm
427
508
610
813
1219
1463
1626
1707
1829
2032
2438
3048
3658
4064
4267
4877
5486
6096
inch
21
25
30
40
60
72
80
84
90
100
120
150
180
200
210
240
270
300 inch
17
20
24
32
48
58
64
67
72
80
96
120
144
160
168
192
216
240 inch
1
1
2
2
3
4
5
5
5
6
7
9
10
12
12
14
16
17 mm
30
40
40
60
90
110
120
120
130
150
180
220
270
300
310
350
400
440
Reflecting the Image
Using a mirror to reflect your projectors image enables you to enjoy a
much larger image. Contact your NEC dealer if you need a mirror. If
youre using a mirror and your image is inverted, use the MENU and
SELECT buttons on your projector cabinet or your remote control to
correct the orientation. (See page E-27.)
W
ARNING
* Installing your projector on the ceiling must be done by a quali-
fied technician. Contact your NEC dealer for more information.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the projector fall\
s
to the ground, you can be injured and the projector severely dam-
aged.
• Do not use the projector where temperatures vary greatly. The pro-
jector must be used at temperatures between 32 ˚F (0 ˚C) and 95 ˚F
(35 ˚C).
• Do not expose the projector to moisture, dust, or smoke. This will
harm the screen image.
• Ensure that you have adequate ventilation around your projector so
heat can dissipate. Do not cover the vents on the side or the front of
the projector. 
						

							E-13
Making Connections
NOTE: When using with a notebook PC, be sure to connect between the projector \
and the notebook PC before turning on the power to the  notebook PC. In most
cases signal cannot be output from RGB output unless the notebook PC is \
turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be th\
e result of the computers screen-saver or power manage ment software.
* If you accidentally hit the POWER button on the remote control, wait 6\
0 seconds and then press the POWER button again to resu me.
PHONE
PHONE
Connecting Your PC or Macintosh Computer
Audio cable (not supplied)
IBM VGA or Compatibles (Notebook type)or Macintosh (Notebook type)
IBM PC or Compatibles (Desktop type)
or Macintosh (Desktop type) RGB signal cable (supplied)
To  mini D-Sub 15-pin connector on the pro-
jector. It is recommended that you use a
commercially available distribution amplifierif connecting a signal cable longer than thesupplied one.
NOTE:  For older Macintosh,
use a commercially available
pin adapter (not supplied) toconnect to your Macs video
port.
Connecting your PC or Macintosh computer to your projector will en-
able you to project your computers screen image for an impressive pre-
sentation.
To  connect to a PC or Macintosh, simply:
1. Turn off the power to your projector and computer.
2. Use the supplied signal cable to connect your PC or Macintosh to the projector.
3. Turn on the projector and the computer. 4. If the projector goes blank after a period of inactivity, it may be caused
by a screen saver installed on the computer youve connected to theprojector. 
						

							E-14
To connect SCART output (RGB)
Before connections: An exclusive SCART adapter (ADP-SC1) and a
commercially available SCART cable are required for this connection.
NOTE:  Audio signal is not available for this connection.
RGB INVideo equipment
such as DVD player Projector
ADP-SC1Commercially available
SCART cable Female
1. Turn off the power to the projector and your video equipment.
2. Use the NEC ADP-SC1 SCART adapter and a commercially avail- able SCART cable to connect the RGB input of your projector and aSCART output (RGB) of your video equipment.
3. Turn on the power to the projector and your video equipment. 4. Use the RGB button on the remote control to select the RGB input.5. Press the MENU button on the remote control to display the menu.6. From the menu, select [Advanced] 
→ [Signal Select RGB] → [Scart].
SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as Euro-connector.
NOTE:  The ADP-SC1 SCART adapter is obtainable from your NEC dealer in Eu-rope. Contact your NEC dealer in Europe for more information.
To  RGB IN
Connecting an External Monitor
You can connect a separate, external monitor to your projector to simul-
taneously view on a monitor the RGB analog image youre projecting.
To   do so:
1. Turn off the power to your projector, monitor and computer.
2. Use a 15-pin cable to connect your monitor to the RGB OUT (Mini D- Sub 15 pin) connector on your projector.
3. Turn on the projector, monitor and the computer.
NOTE: • The RGB OUT connector outputs RGB signal during standby mode. When the
projector goes into standby mode, the image on an external monitor disap\
-pears for a moment.
• When the projector is in the standby mode, the image may not be correctl\
y
displayed while the cooling fans are running immediately after turning o\
n oroff the power.
• Daisy chain connection is not possible.
PHONE
Audio cable (not supplied)
RGB signal cable (not supplied)
RGB signal cable (supplied) 
						

							E-15
RGB IN
AUDIO OUTL
AUDIO INLRRComponentYCbCr
Connecting Your DVD PlayerDVD player
You can connect your projector to a DVD player with component output
or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use a commercially available component video cable (RCA

3) and the
optional 15-pin-to-RCA (female)
3 cable to connect your DVD player
to the RGB IN connector on the projector. Component video RCA

3 cable
(not supplied)
For a DVD player without component video (Y,Cb,Cr) output, use
common RCA cables (not provided) to connect a composite VIDEOoutput of the DVD player to the Video Input of the projector.
3. Turn on the projector and DVD player.
NOTE:  Refer to your DVD players owners manual for more information aboutyour DVD players video output requirements.
Optional 15-pin-to-RCA
(female)

3 cable (ADP-CV1)
Audio cable (not supplied)
Audio Equipment 
						

							E-16
AUDIO OUTLR
AUDIO INLR
VIDEO OUT
S-VIDEO OUT
VCR/ Laser disc player
Connecting Your VCR or Laser Disc Player
Audio equipment
S-Video cable (not supplied)
V
ideo cable (not supplied)
Audio cable(not supplied)
Use common RCA cables (not provided) to connect your VCR, laser
disc player or document camera to your projector.
To  make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or
document camera.
2. Connect one end of your RCA cable to the video output connector on the back of your VCR or laser disc player, connect the other end to
the Video input on your projector. Use an audio cable (not supplied)to connect the audio from your VCR or laser disc player to your audio
equipment (if your VCR or laser disc player has this capability). Becareful to keep your right and left channel connections correct for
stereo sound.
3. Turn on the projector and the VCR or laser disc player.
NOTE:  Refer to your VCR or laser disc player owners manual for more informa-tion about your equipments video output requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video sourceis played back in fast-forward or fast-rewind via a scan converter.
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cables two-pin plug to
the AC IN of the projector, and then connect the other
plug of the supplied power cable in the wall outlet. 
						

							E-17
PROJECTING AN IMAGE (BASIC OPERATION)
This section describes how to turn on the projector and to project a
picture onto the screen.
Turning on the Projector
NOTE:
• The projector has two power switches: main power switch and POWER (ON/
STAND BY) button (POWER ON and OFF on the remote control).
• When plugging in or unplugging the supplied power cable, make sure that \
the
main power switch is pushed to the off (O) position. Failure to do so \
may
cause damage to the projector.
To  turn on the main power to the projector, press the Main Power switch
to the on position ( I ).
Before you turn on your projector, ensure that the computer or video
source is turned on and that your lens cap is removed.
Only after you press the POWER (ON/STAND BY) button on the pro-
jector cabinet or POWER ON button on the remote control for a mini-
mum of 2 seconds will the power indicator turn to green and the projec-
tor become ready to use.
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup screen. This
screen gives you the opportunity to select one of the 21 menu languages.\
To  select a menu language, follow these steps:
1. Use the SELECT G or H button to select one of the 21 languages for
the menu.
After this has been done, you can proceed to the menu operation.
If you want, you can select the menu language later. See Language
on page E-27.
NOTE:  Immediately after turning on the projector, screen flicker may occur. Thisis not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.
When the Lamp mode is set to Eco, the Lamp indicator will light green.
If one of the following things happens, the projector will not turn on.
*If the internal temperature of the projector is too high, the projector
detects abnormal high temperature. In this condition the projector
will not turn on to protect the internal system. If this happens, wait f\
or
the projectors internal components to cool down.
* When the lamp reaches its end of usable life, the projector will not
turn on. If this happens, replace the lamp.
* If the lamp fails to light, and if the STATUS indicator flashes on and
off in a cycle of six times, wait a full minute and then turn on the
power.
2. Press the ENTER button to execute the selection. 
						

							E-18
Selecting a Source
Selecting the computer or video source
Using the Remote Control
OFFONVIDEOS-VIDEORGB
PJ
MAGNIFY
SELECT
EMNU
TERNENCEACL
AUTO ADJ.
FREEZEPIC-MUTEPICTURE
VOLUME
HELP
ASPECT
POWER
Press any one of the RGB, VIDEO or
S-VIDEO buttons.
Using the cabinet buttons
Adjusting the Picture Size and PositionPlace your projector on a flat level surface and ensure that the project\
or
is square to the screen.
Lift the front edge of the projector to center the image vertically.
* If the projected image does not appear square to the screen then
use the Keystone feature for proper adjustment. See page E-19.
Move the projector left to center the image horizontally on the screen.
Adjust the Tilt Foot
1. Lift the front edge of the projector. Adjustable Tilt Foot Lever Adjustable Tilt Foot
2. Push up the Adjustable Tilt Foot Levers on the right and left sides of the projector to extend the adjustable tilt feet (maximum height).
3. Push down the Adjustable Tilt Foot Levers.
4. Lower the front of the projector to the desired height (max. 40mm/1.6”) and release the Adjustable Tilt Foot Lever to lock the Adjust-able tilt foot. There is approximately 10 degrees of up and down ad-justment for the front of the projector.
Adjustable Tilt Foot Lever
NOTE:  If no input signal is available, the projector will display a blue backg\
round(factory preset).
Press any one of the RGB,
VIDEO or S-VIDEO buttons.