NEC Visualink 128/384 Quick Installation Guide

							NDA-24232 Issue 2.0Page 3-1
VisuaLink 128/384 Quick Installation Guide Chapter 3
Chapter 3  Startup Screen for the VisuaLink 128 and VisuaLink 384
When you first turn on your VisuaLink, there will be an initial configuration 
screen.  These configuration screens will have to be completed before your system 
becomes operational.
3.1 Start up 
configuration 
screensThe following are the startup screens that will be active on first power up or acti-
vated on demand by the user after choosing the Environmental initialize. 
Welcome Screen:  
This is a welcome screen for the User.
Vi s u a L i n k
Thank you for purchasing one of the most
simple and portable video conferencing systems 
available.
We will now show you how to set up your system.  
This will only have to be done once.
NOTE: If remote controller doesn’t work, make 
sure the switch setting of D30 camera IR 
out is ON.  Switch is located on the 
bottom of the camera.
 Click here to continue
    Configure laters
Note is yellow 
						

							Page 3-2NDA-24232 Issue 2.0 
Chapter 3 VisuaLink 128/384 Quick Installation Guide
Remote Controller Directions: 
Gives some general directions for configure the VisuaLink system.  Using the 
Remote controller highlight the NEXT option to advance to the configure screen 
or press the lower portion of the CAMERA CONTROL key to highlight the 
Configure Later to advance to the normal ICON screens.  If you choose to 
configure later, the system will have to be programmed with My numbers and 
SPID’s in order to work correctly.
3.2 Setting Up your 
ISDN Line 
InformationThe following is a description of BRI Line setup
Part 1- Remote Controller Location
-  Locate the CAMERA control.
The CAMERA control key  is the BLUE round 
key.  Use this key to move the Cursor 
up/down and Left/Right in the Configuration
Screens.
-  Locate the ENTER key on the Wireless remote
   controller.
Use the ENTER key to confirm selections 
and store information.
   Next screen 
     Prior screen
s
Part 2- Setting up Your ISDN Line 
Introduction:
When ordering BRI service,  you will usually get 
2 My numbers and 2 SPID numbers per BRI.  
A SPID normally consists of the user’s 3 digit  
area code, 7 digit ISDN telephone number, 
followed by a 0101. Ex:
      MY Number 1: 9727195854
      SPID 1:  97271958540101 
Note: The VisuaLink 128 requires 2 My numbers 
and 2 SPID #, while the VisuaLink 384 
requires 6 My numbers and 6 SPID #.
 Next screen
    Prior screen
s
Note is yellow 
						

							NDA-24232 Issue 2.0Page 3-3
VisuaLink 128/384 Quick Installation Guide Chapter 3
Video Number 1 Screen’s
Using the number pad of the wireless remote enter My Number with area code 
and SPID numbers associated to Line  (BRI 1).  Each BRI will have My numbers 
labeled #1 and #2 and two SPID’s.  All four numbers must be entered.  Choose 
NEXT when complete.  
Note:
“PROCEED TO STEP 2” will only be shown on the VisuaLink 128 system.  
VisuaLink 384 will show “Proceed to Line 2 Setup”   
Step 1--Enter My Number and SPID for BRI LINE 1
     My Number 1:
 []
     SPID 1:
    [ ]
    My Number 2:
    [ ]
    SPID 2:
    [ ]
Next screen
Prior screen
Press  ENTER after choosing each item
s
Step 1--Enter My Number and SPID for BRI LINE 1
     My Number 1:
    [9727195854]
     SPID 1:
    [97271958540101]
    My Number 2:
 [9727195855]
    SPID 2:
    [97271958550101 ]
Next screen
Prior screen
Press  ENTER after choosing each item
s 
						

							Page 3-4NDA-24232 Issue 2.0 
Chapter 3 VisuaLink 128/384 Quick Installation Guide
Video Number 2 Screens:
Using the number pad of the wireless remote enter My Number with area code 
and SPID numbers associated to Line  (BRI 2).  Each BRI will have My numbers 
labeled #1 and #2 and two SPID’s.  All four numbers must be entered.  Choose 
NEXT when complete.
Note:
  This screen will only appear on the VL 384 system.
Step 1--Enter My Number and SPID for BRI LINE 2
    My Number 1:
 []
    SPID 1:
    [ ]
    My Number 2:
    [ ]
    SPID 2:
    [ ]
Next screen
Prior screen
Press  ENTER after choosing each item
s 
						

							NDA-24232 Issue 2.0Page 3-5
VisuaLink 128/384 Quick Installation Guide Chapter 3
Video Number 3 Screens:
Using the number pad of the wireless remote enter My Number with area code 
and SPID numbers associated to Line  (BRI 3).  Each BRI will have My numbers 
labeled #1 and #2 and two SPID’s.  All four numbers must be entered.  Choose 
NEXT when complete.
Note: 
 This screen will only appear on the VL 384 system.
3.3 Optional User 
Settings:The following is a description for Optional Setting screen.
Step 1--Enter My Number and SPID for BRI LINE 3
    My Number 1:
 []
    SPID 1:
    [ ]
    My Number 2:
    [ ]
    SPID 2:
    [ ]
Next screen
Prior screen
Press  ENTER after choosing each item
s
Part 3 - Optional User Settings
Introduction:
Site Name: Name identification for your 
location.  Name is displayed on 
far-end monitor when site is viewed.
Password: Required to gain access to the 
VisuaLink configuration screens.
Time display: Sets the internal clock for the 
Vi s u a L i n k .
  Next screen 
     Prior screen
s 
						

							Page 3-6NDA-24232 Issue 2.0 
Chapter 3 VisuaLink 128/384 Quick Installation Guide
Optional information:
You may enter this optional information.  The name you enter makes it easy for 
users to identify this particular VisuaLink.  The name can be up to 20 characters 
long.  The Password is the password needed to be entered when selecting the 
Utilities ICON.  After entering the optional information select the NEXT to 
advance to the next screen.  
Application Screen’s
Using the number pad on the wireless remote controller select the application 
which the VisuaLink is installed.  Your answer to this question will automatically 
configure the internal parameters for the following:
Step 1-  Optional User Settings
Your Site Name        
[                           ]
Password  [          ]
Time Setting 
[12/1/1998   10:50]
Time Display:  
Auto Power Save:  
Next screen
Prior screen
Press ENTER after choosing each items
Item Rollabout/Other Data Conference Gateway Desktop
Serial Port 1 Camera EVI-D30 T.120 Camera Camera
Serial Port 2 Console Console Console Console
Audio Mode G.722 G.728 G.722 G.722
MLP 4.0 24.0 4.0 4.0
Answer Mode Auto Auto Auto Manual
LSD 1.2 Off 1.2 1.2
Ext. Remote Auto Off Off Off
H.263 Off Off Off Off
Lip Sync On On On On 
						

							NDA-24232 Issue 2.0Page 3-7
VisuaLink 128/384 Quick Installation Guide Chapter 3
Congratulations Screen
The VisuaLink is now setup for the configuration you have entered.  Press the 
ENTER button on the REMOTE CONTROLLER, the VisuaLink will display a 
blue screen and recycle.  The VisuaLink should will power up to a normal state.   
You may begin to use the video conferencing system immediately.
Note:
If there are no My Numbers entered in the configuration the VisuaLink 
will display the Start Up screens.
Step 2—Optional User Settings
Key in the number of one of the following 
applications.
Applications:
1.  Rollabout/Other
2.  Data Conference
3.  Gateway
4.  Desktop
Press CANCEL to page back
Congratulations, you have just finished setting 
up your VisuaLink system.  
For VisuaLink software updates and general 
VisuaLink knowledge, visit the NEC Knowledge 
base web site at : 
http://www.cng.nec.com  or
http://www.ilibrary.com/phoenix/ntachome.nsf 
/homepagenav?opennavigator
- You may begin to use the video conferencing 
system immediately.
- Press ENTER to activate your configuration.  
Press CANCEL to page back 
						

							Page 3-8NDA-24232 Issue 2.0 
Chapter 3 VisuaLink 128/384 Quick Installation Guide
VisuaLink system start up screen.
Changing the configuration
It is important that the CODEC is set up with a local number and SPID numbers.  
If the unit is not setup with a local number (my number) and SPID, the unit will 
not allow for dialing and receiving of video calls.  If you have entered these 
numbers in the Start Up configuration, you may ignore this section.  If the 
VisuaLink environment has changed, such as the phone number have changed, 
you must reconfigure the numbers in the VisuaLink.             
America, Inc.
         VisuaLink
Powering Up
Ver .22.02.37 
						

							NDA-24232 Revision 1.0Page 4-1
VisuaLink 128/384 Quick Installation Guide Chapter 4
Chapter 4  Rollabout 128/384 Procedures
4.1 Rollabout System 
ConnectionsUse the following procedures to set up the VisuaLink 128 or VisuaLink 384.  See 
Appendix A for system drawings for the VisuaLink 128.  See Appendix B for the 
system drawings for the VisuaLink 384.
Note:
This guide provides connection diagrams for manufacturer-specific 
components.  If your system contains components from other manufacturers, 
please consult their documentation.
Figure 4-1:   Equipment Placement
12 VIDEO INS-VIDEO
VIDEO
AUDIOL
MONO
RAUDIO OUT
(VAR/FIX)
12 VIDEO IN
S-VIDEO
VIDEO
AUDIOL
MONO
RAUDIO OUT
(VAR/FIX)
+
+
++
+DC IN 5V+ -  Serial1           Serial2/RMT
O
U
T
I
N
VIDEO2                                VIDEO1            AUDIO
++TEL                           S/T LINEMI C1                                   MIC2                                   MIC3
AUDIO
VIDEO
S VIDEOIN VISCA OUT POWER
OFF ONDC IN
13.5 V+ -MICCAMERA NO.1    2   3
CAMERA REAR
MONITOR REAR
VisuaLink 128 REAR
NT1 REAR
VHF/UHF
S/T
S/TL-BK    LINE   PWR
DIN
INTERFACE
1234
5ONPOWER
U
NT1 FRONT
+
+
++
+DC IN 5V+ -  Serial1           Serial2/RMT
O
U
T
I
N
VID EO2                                V IDEO1            A UDIO
++TEL                 S/T LIN E 1                   S /T LINE 2                 S/T LINE 3MIC1               MIC2             MIC 3
VisuaLink 384 REAR
Note:
  Connector location on 
the monitor may vary.Note: Labeling for the connector may vary.
Control, Video,
& Audio Hole
Power Cable Hole 
						

							Page 4-2NDA-24232 Revision 1.0
Chapter 4 VisuaLink 128/384 Quick Installation Guide
4.2  Step-by-Step 
ProcedureThe following are the steps and procedures for the installation of the VisuaLink 
128/384.
STEP ACTION DRAWING
1. Locate and unpack the Cabinet box.
2. Locate Power Strip at bottom-left (looking 
through the front) of cabinet and feed power cable 
through the power opening at rear of cabinet.
3. Plug power strip power cable into AC outlet.  
Make sure the ON/OFF switch on the upper right 
outside of the cabinet is in the OFF position.
Note:
The power switch will be lit when the 
power strip is in the ON position.
Powerstr ip
Power Switch