NEC V221w Bk Users Manual
Have a look at the manual NEC V221w Bk Users Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Index Warning, Caution ......................................................................................................................... English-1 Registration Information ............................................................................................................... English-1 Contents ....................................................................................................................................... English-3 Quick Start ................................................................................................................................... English-3 Controls ........................................................................................................................................ English-6 Recommended use ...................................................................................................................... English-9 Specifications - V191W .............................................................................................................. English-11 Specifications - V221W .............................................................................................................. English-12 Features ..................................................................................................................................... English-13 Troubleshooting ......................................................................................................................... English-14 TCO’03 ....................................................................................................................................... English-15 Manufacturer’s Recycling and Energy Information .................................................................... English-16
English English-1 WARNING CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems. TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNITS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Declaration of the Manufacturer We hereby certify that the colour monitors V191W (TFT185W80PS)/V221W (TFT22W90PS) are in compliance with: Council Directive 2006/95/EC: – EN 60950-1 Council Directive 2004/108/EC: – EN 55022 – EN 61000-3-2 – EN 61000-3-3 – EN 55024and marked with NEC Display Solutions, Ltd. 4-13-23, Shibaura, Minato-Ku Tokyo 108-0023, Japan CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country. Plug Type North AmericaEuropean ContinentalU.K. Chinese Japanese Plug Shape Country VoltageU.S.A./Canada U.K. China JapanEU (except U.K.) 120* 230 220 100230 *When operating the V191W/V221W monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply voltage of the AC power outlet being used. NOTE:This product can only be serviced in the country where it was purchased. Registration Information Declaration
English-2 Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information 1.Use the attached specified cables with the V191W/V221W color monitor so as not to interfere with radio and television reception. (1) The power supply cord you use must have been approved by and comply with the safety standards of U.S.A., and meet the following condition. Power supply cord Non shield type, 3-conductor Plug shape U.S.A (2) Please use the supplied shielded video signal cable, 15-pin mini D-SUB to D-SUB cable or DVI-D to DVI-D cable. Use of other cables and adapters may cause interference with radio and television reception. 2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult your dealer or an experienced radio/TV technician for help. If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4. Declaration of Conformity This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.S. Responsible Party: NEC Display Solutions of America, Inc. Address: 500 Park Blvd, Suite 1100 Itasca, Illinois 60143 Tel. No.: (630) 467-3000 Type of Product: Display Monitor Equipment Classification: Class B Peripheral Models: V191W (TFT185W80PS) V221W (TFT22W90PS) We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules. Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. E NERGY STA R is a U.S. registered trademark. ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, Norway, Spain, Sweden, U.K. All other brands and product names are trademarks or registered trademarks of their respective owners. As an E NERGY STA R® Partner, NEC Display Solutions of America, Inc. has determined that this product meets the ENERGY STA R guidelines for energy efficiency. The ENERGY STA R emblem does not represent EPA endorsement of any product or service.
English English-3 Contents Your new NEC LCD monitor box* should contain the following: •LCD monitor with tilt base •Power Cord •Video Signal Cable •Setup Manual •CD-ROM (only EU) •Base Stand •Stand Neck Quick Start To attach the Neck/Base to the LCD monitor. 1. Insert the front of the Stand neck into the holes in the front of Base stand. The snapping tabs on the Base stand should fit into the hole on the Stand neck (Figure S.1). 2. Insert the front of the Stand neck into the holes in the LCD monitor. The snapping tabs on the LCD monitor should fit into the hole on the Stand neck (Figure S.1). To attach the LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2.For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable connected with the monitor to the connector of the display card in your system (Figure A.1). Tighten all screws. For the Mac: Connect the Macintosh cable adapter (not included) to the computer. Attach the 15-pin mini D-SUB signal cable to the Macintosh cable adapter (Figure A.2). Tighten all screws. NOTE:Some Macintosh systems do not require a Macintosh cable adapter. Setup ManualPower Cord(Type of power cord included will depend on the where the LCD monitor is to be shipped)Video Signal Cable LCD monitor (Stand not connected) CD-ROM (only EU) *Remember to save your original box and packing material to transport or ship the monitor. Figure A.2 Macintosh Cable Adapter (not included) Figure A.1Figure S.1 LCD monitor Base standStand neck Setup Manual
English-4 Figure R.1 Non-abrasive surface Figure R.2 3. Connect one end of the power cord to the monitor and the other end to the power outlet (Figure B.1). NOTE:Please confirm that the tabs are completely secure. NOTE:Please refer to Caution section of this manual for proper selection of power cord. 4. Turn on the monitor with the front power button and the computer (Figure C.1). Figure B.1 Figure C.1 Power Button 5. No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings. For further adjustments, use the following OSD controls: •Image Setup •Image Position Refer to the Controls section of this User’s Manual for a full description of these OSD controls. NOTE:If you have any problem, please refer to the Troubleshooting section of this User’s Manual. Tilt Grasp both sides of the monitor screen with your hands and adjust the tilt as desired (Figure TS.1). Remove Monitor Stand for Mounting To prepare the monitor for alternative mounting purposes: 1. Disconnect all cables. 2. Place monitor face down on a non-abrasive surface (Figure R.1). 3. Insert the thin rod into the hole in the back of LCD monitor and using your thumbs, press the tabs on the back side of base stand in the direction of the arrows the pull out the stand as indicated (Figure R.1) 4. Connect the AC cord to the back of the monitor (Figure R.2). 5. Reverse this process to re-attach stand. NOTE:Use only VESA-compatible alternative mounting method. NOTE:Handle with care when removing monitor stand.Figure TS.1 Tabs18˚ Tilt D-Sub Power Cord
English English-5 Removing the Base NOTE:Always remove the Base when shipping the LCD. 1. Place monitor face down on a non-abrasive surface (Figure R.1). 2. Insert the thin rod into the hole in the back of LCD monitor and using your thumbs, press the tabs on the back side of base stand in the direction of the arrows the pull out the stand as indicated (Figure R.1). Connecting a Flexible Arm This LCD monitor is designed for use with a flexible arm. Please use the screws (4pcs) as shown in the picture when installing. To meet the safety requirements, the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor. The LCD monitor shall only be used with an approved arm (e.g. GS mark). 4 x 12 mm with lock washer and flat washer Tighten all screws 100 mm 100 mmThickness of Bracket (Arm) 2.0 ~ 3.2 mm 4-SCREWS (M4) (MAX depth: 8.5 mm) Weight of LCD assembly: 3.0 kg (MAX) - (V191W) 4.1 kg (MAX) - (V221W) Specifications 12 mm M4
English-6 Controls OSD (On-Screen Display) control buttons on the front of the monitor function as follows: 1. Basic function at pressing each key 2. OSD structure Showing OSD.Shortcut to Bright adjust window. Button At No OSD showingShortcut to Contrast adjust window.“Auto adjust” operate. At OSD showing(Icon selection stage)Go to Adjustment stage. Cursor goes to left. Cursor goes to right. At OSD showing(Adjustment stage)Go to Icon selection stage. Adjust value decrease or Cursor for adjust goes to left.Adjust value increase or Cursor for adjust goes to right.Reset operation. Main Menu (Icon Select) Sub Menu (Icon Select)Press “MENU” keyPress “MENU” key Press “–” or “+”Main Menu (Adjust) Sub Menu (Adjust)Press “MENU” key Press “MENU” keyAdjust by using “–” or “+” Adjust by using “–” or “+” Press “–” or “+” Example Tool: Press “MENU” key Press “MENU” key
English English-7 BRIGHTNESSAdjusts the overall image and background screen brightness. To enter the ECO MODE, press the “AUTO” button. CONTRAST Adjusts the image brightness in relation to the background. AUTO CONTRAST Adjusts the image displayed for non-standard video inputs. AUTO ADJUST Automatically adjusts the Image Position, the H. Size and Fine setting. LEFT/RIGHT Controls Horizontal Image Position within the display area of the LCD. DOWN/UP Controls Vertical Image Position within the display area of the LCD. H. SIZE Adjusts the horizontal size by increasing or decreasing this setting. FINE Improves focus, clarity and image stability by increasing or decreasing this setting. COLOUR CONTROL SYSTEMS Five colour presets (9300/7500/sRGB/USER/NATIVE) select the desired colour setting. COLOUR RED Increase or decreases Red. The change will appear on screen. COLOUR GREEN Increase or decreases Green. The change will appear on screen. COLOUR BLUE Increase or decreases Blue. The change will appear on screen. TOOL Selecting TOOL allows you to get into the sub menu. FACTORY PRESET Selecting Factory Preset allows you to reset all OSD control settings back to the factory settings. Individual settings can be reset by highlighting the control to be reset and pressing the “+” button. EXIT Selecting EXIT allows you exit OSD menu/ sub menu. LANGUAGE OSD control menus are available in nine languages. OSD TURN OFF The OSD control menu will stay on as long as it is in use. In the OSD Turn OFF submenu, you can select how long the monitor waits after the last touch of a button to shut off the OSD control menu. The preset choices are 10 - 120 seconds by 5 seconds step.
English-8 OSD LOCK OUT This control completely locks out access to all OSD control functions without Brightness and Contrast. When attempting to activate OSD controls while in the Lock Out mode, a screen will appear indicating the OSD are locked out. To activate the OSD Lock Out function, press “AUTO”, then “+” key and hold down simultaneously. To de-activate the OSD Lock Out, press “AUTO”, then “+” key and hold down simultaneously. RESOLUTION NOTIFIER If ON is selected, a message will appear on the screen after 30 seconds, notifying you that the resolution is not at optimal resolution. EXPANSION Selects the zoom mode. FULL: The image is expanded to full screen, regardless of the resolution. ASPECT: The image is expanded without changing the aspect ratio. DDC/CI Turns ON or OFF the two way communication and control of the monitor. MONITOR INFO Indicates the model and serial numbers of your monitor. CARBON SAVING Show saving value of Carbon foot print. Carbon meter value is updated each 5 min. INPUT RESOLUTION V191W Select resolution’s priority of input signal to one of the following signal: 1280x768, 1360x768, 1366x768. V221W Select resolution’s priority of input signal to one of the following signal: 1280x768, 1360x768 and 1366x768 or 1400x1050 and 1680x1050. 1280x768, 1360x768, 1366x768: Determines the resolution to 1280x768, 1360x768 or 1366x768. 1400x1050, 1680x1050: Determines the resolution to 1400x1050 or 1680x1050. OSD Warning OSD Warning menus disappear with MENU button. NO SIGNAL: This function gives a warning when there is no signal present. After power is turned on or when there is a change of input signal or video is inactive, the No Signal window will appear. OUT OF RANGE: This function gives a recommendation of the optimized resolution and refresh rate. After the power is turned on or there is a change of input signal or the video signal doesn’t have proper timing, the Out Of Range menu will appear.