NEC V 423 User Manual

User’s Manual
MultiSync V423
MultiSync V463 

Index
DECLARATION OF CONFORMITY ........................................................................\
..................................... English-1
Important Information ........................................................................\
................................. .......................... English-2
WARNING  ........................................................................\
....................................................... ........ English-2
CAUTION...

English-1
English
DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to \
the following two conditions. (1) This device may not 
cause harmful interference, and (2) this device must accept any interf\
erence received, including interference that may cause 
undesired operation.U.S. Responsible Party:  NEC Display Solutions of America, Inc.
Address:    500 Park Boulevard, Suite 1100
    Itasca, Illinois 60143
Tel. No.:   (630) 467-3000
Type of Product:  Display...

English-2
Important Information
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT 
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE 
PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. 
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
CAUTION:   TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE...

English-3
EnglishFOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING  THE MULTI-FUNCTION MONITOR:
•  DO NOT OPEN THE MONITOR . There are no user 
serviceable parts inside and opening or removing covers may 
expose you to dangerous shock hazards or other risks. Refer 
all servicing to qualifi ed service personnel.
•  Do not spill any liquids into the cabinet or use your monitor  near water.
•  Do not insert objects of any kind into the cabinet slots,  as they may touch dangerous...

English-4
Contents
Your new MultiSync monitor box* should contain the following:
• LCD monitor
• Power cord*
1
•  Video Signal Cable
•  Wireless Remote Control and AA Batteries• Setup Manual
•  Clamp x 1
•  Screw with washer (M4 x 10) x 1
• CD-ROM
Power Cord*1
Setup ManualClamp x 1
CD-ROM Screw with washer 
(M4 x 10) x 1
Setup Manual
Video Signal Cable 
(DVI-D to DVI-D cable)
Wireless Remote Control and AA  Batteries
*  Remember to save your original box and packing material to transport or \
ship the...

English-5
EnglishThis device cannot be used or installed without the Tabletop 
Stand or other mounting accessory for support. For proper 
installation it is strongly recommended to use a trained, 
NEC authorized service person. Failure to follow NEC 
standard mounting procedures could result in damage to the 
equipment or injury to the user or installer. Product warranty 
does not cover damage caused by improper installation. 
Failure to follow these recommendations could result in 
voiding the...

English-6
Attaching Mounting Accessories
The monitor is designed for use with the VESA mounting 
system.
1. Attach Mounting Accessories
Be careful to avoid tipping monitor when attaching 
accessories.
VESA Mounting Interface
300 mm
300 mm
Mounting accessories can be attached with the monitor in 
the face down position. To avoid damaging the screen face, 
place the protective sheet on the table underneath the LCD. 
The protective sheet was wrapped around the LCD in the 
original packaging. Make sure...

English-7
English
5. Prevent Tipping
When using the display with the optional table top stand 
fasten the LCD to a wall using a cord or chain that can 
support the weight of the monitor in order to prevent the 
monitor from falling. Fasten the cord or chain to the monitor 
using the provided clamps and screws.
Screw (M4)*Cord or chain
Clamp*
295 mm
Screw Holes
*: included in option stand.
Before attaching the LCD monitor to the wall, make sure that 
the wall can support the weight of the monitor.
Be...

English-8
Parts Name and Functions
Control Panel
 POWER button
Switches the power on/off. See also page 16.
 MUTE button
Switches the audio mute ON/OFF.
 INPUT button
Acts as SET button within OSD menu. (Toggle switches 
between [DVI], [DPORT], [VGA], [HDMI], [DVD/HD], 
[SCART], [VIDEO1], [VIDEO2] or [S-VIDEO]). These are 
available input only, shown as their factory preset name.
 PLUS button 
Acts as (+) button to increase the adjustment with OSD menu.
Increases the audio output level when the OSD...