NEC Projector UM361X User Manual

100
5. Using On-Screen Menu
[SOURCE(1)]
[SOURCE	NAME]	[SOURCE	INDEX]
[HORIZONTAL	FREQUENCY]	[VERTICAL	FREQUENCY]
[SYNC	TYPE]	 [SYNC	POLARITY]
[SCAN	TYPE]
[SOURCE(2)]
[SIGNAL	 TYPE]	 [VIDEO	TYPE]
[BIT	DEPTH]	 [VIDEO	LEVEL]
[MHL	SIGNAL]
[WIRED LAN]
[IP	ADDRESS]	[SUBNET	MASK]
[GATEWAY]	[MAC	ADDRESS] 

101
5. Using On-Screen Menu
[WIRELESS LAN]
[IP	ADDRESS]	[SUBNET	MASK]
[GATEWAY]	[MAC	ADDRESS]
[SSID]	[NETWORK	TYPE]
[WEP/WPA]	 [CHANNEL]
[SIGNAL	LEVEL]
[VERSION]
[FIRMWARE]	Version
[DATA]	Version
[OTHERS]
[PROJECTOR	NAME]
[MODEL	NO.]
[SERIAL	NUMBER]
[LAN	UNIT	 TYPE]
[CONTROL	ID]	(when	[CONTROL	ID]	is	set) 

102
5. Using On-Screen Menu
 Menu Descriptions & Functions [RESET]
Returning to Factory Default [RESET]
The	RESET	 feature	allows	you	to	change	 adjustments	 and	settings	 to	the	 factory	 preset	for	a	(all)	 source	 (s)	except	
the	following:
[CURRENT	SIGNAL]
Resets	the	adjustments	for	the	current	signal	to	the	factory	preset	levels. 	
The	items	 that	can	be	reset	 are:	[PRESET],	 [CONTRAST],	 [BRIGHTNESS],	 [COLOR],	[HUE],	[SHARPNESS],	
[ASPECT	RATIO],	[HORIZONTAL],	[VERTICAL],	[CLOCK],	[PHASE],	and...

103
1 Setting Up the Screen and the Projector
[UM361X/UM301X]
The	further	 your	projector	 is	from	 the	screen	 or	wall,	 the	larger	 the	image. 	The	 minimum	 size	the	image	 can	be	is	61.5"	
(1562	 mm)	measured	 diagonally	 when	the	projector	 is	4	inches	 (105	mm)	between	 the	screen	 side	of	the	 projector	
and	the	wall	or	screen. 	The	largest	the	image	can	be	is	116.6"	(2962	mm)	when	the	projector	is	20	inches	(510	mm)	
between	the	screen	side	of	the	projector	and	the	wall	or	screen....

104
6. Installation and Connections
[UM351W/UM301W]
The	further	 your	projector	 is	from	 the	screen	 or	wall,	 the	larger	 the	image. 	The	 minimum	 size	the	image	 can	be	is	58"	
(1473	 mm)	measured	 diagonally	 when	the	projector	 is	4	inches	 (105	mm)	between	 the	screen	 side	of	the	 projector	
and	 the	wall	 or	screen. 	The	 largest	 the	image	 can	be	is	110"	 (2794	 mm)	when	 the	projector	 is	20	 inches	 (510	mm)	
between	the	screen	side	of	the	projector	and	the	wall	or	screen....

105
6. Installation and Connections
WARNING
*	 Installing	your	projector	 on	the	 ceiling	 must	be	done	
by	a 	qualified 	technician. 	Contact 	your 	NEC 	dealer 	for	
more	information.
*	 Do	not	attempt	to	install	the	projector	yourself.
•	 Only	 use	your	 projector	 on	a	solid,	 level	surface. 	If	 the	
projector	 falls	to	the	 ground,	 you	can	 be	injured	 and	
the	projector	severely	damaged.
•	 Do	not	use	 the	projector	 where	temperatures	 vary	
greatly.	The	 projector	 must	be	used	 at	temperatures...

106
6. Installation and Connections
 Making Connections
Connecting Your Computer
Computer	cables,	HDMI	and	USB	 can	be	used	 to	connect	 to	a	computer. 	The	 connection	 cable	is	not	 enclosed	 with	
the	projector. 	Please	get	ready	a	suitable	cable	for	the	connection.
NOTE:	Signals	supported	by	Plug	&	Play	(DDC2)
INPUT
COMPUTER IN
HDMI 1/MHL IN HDMI 2 IN
analog digitaldigital
Yes YesYes
A commercially available 
USB cable 
(compatible with USB 2.0 
specifications)
Computer cable (VGA) (supplied)
To...

107
6. Installation and Connections
NOTE:	The	projector	is	not	compatible	with	video	decoded	outputs	of	the	NEC	ISS-6020	switcher.
NOTE:	An	image	may	not	be	displayed	correctly	when	a	Video	source	is	played	back	via	a	commercially	available	scan	converter.	
This	is	because	the	projector	will	process	a	video	signal	as	a	computer	signal	at	the	default	setting.	In	that	case,	do	the	following.
*	 When	an	image	is	displayed	with	the	lower	and	upper	black	portion	of	the	screen	or	a	dark	image	is	not	displayed...

108
6. Installation and Connections
Connecting an External Monitor
You	can	connect	 a	separate,	 external	monitor	to	your	 projector	 to	simultaneously	 view	on	a	monitor	 the	computer	
analog	image	you’re	projecting.
NOTE:
•	 When	audio	equipment	is	connected,	the	projector	speaker	is	disabled.
•	 The	signal	output	from	the	MONITOR	OUT	(COMPUTER)	of	this	projector	is	for	projecting	image	on	exclusive	one	display.
•	 When	 no	signal	 is	applied	 over	3	minutes	 in	the	 condition	 of	projector	 standby...

109
6. Installation and Connections
Connecting Your DVD Player or Other AV Equipment
Connecting	Video	Input
•	 Select	the	source	name	for	its	appropriate	input	terminal	after	turning	on	the	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
VIDEO	IN	VIDEO(VIDEO)
NOTE:	Refer	to	your	VCR	owner’s	manual	for	more	information	about	your	equipment’s	video	output	requirements.
NOTE:	 An	image	 may	not	be	displayed	 correctly	when	a	Video	 source	 is	played	 back	in...