NEC Projector UM301X User Manual

							30
3. Convenient Features
7. Use the ▲▼◀▶ button to move the projected image frame as shown on the example.
8.  Press the ENTER button.
9.  Use the ▲▼◀▶ button to select another icon which points in the direction.
	 On	the	Cornerstone	adjustment	screen,	select	[EXIT]	or	press	the	EXIT	button	on	the	remote	control.
  The confirmation screen is displayed.
10. Press the ◀ or ▶	button	to	highlight	the	[OK]	and	press	the	ENTER	button.
This	completes	the	Cornerstone	correction.
Selecting	[CANCEL]	will	return	to	the	adjustment	screen	without	saving	changes	(Step	3).
Selecting	[RESET]	will	return	to	the	factory	default.
Selecting	[UNDO]	will	exit	without	saving	changes. 
						

							31
3. Convenient Features
Pincushion
1.	 Press	the	KEYSTONE	button	with	no	menu	displayed.
 The KEYSTONE screen will be displayed.
 
•	 Press	the	KEYSTONE	button	when	using	the	remote	control.
2. Press the 	button 	to	 select	 either	PINCUSHION 	ADJUSTMENT 	LEFT/RIGHT 	or	 PINCUSHION 	ADJUSTMENT 	
TOP/BOTTOM.
 
3. Press either  or  button to reform pincushion distortion.
 
4.	 Press	the	EXIT	when	PINCUSHION	adjustment	is	completed.
NOTE:	
•	 Even	when	the	projector	is	turned	on,	the	last	used	correction	values	are	applied.
•	 [PINCUSION]	 and	[CORNERSTONE]	 corrections	can	cause	 the	image	 to	be	 slightly	 blurred	because	 the	correction	 is	made	 elec-
tronically.
Reset	the	keystone	adjustment	to	the	initial	value
1.	 Press	the	KEYSTONE	button	with	no	menu	displayed.
  ON the displayed KEYSTONE menu, set the cursor at RESET using the  button and press ENTER button.
 
•	 Confirmation	message	is	displayed	on. 
						

							32
3. Convenient Features
2. Move the cursor onto YES using either  or  button and then press the ENTER.
 
NOTE:
•	 All	adjusted	values	set	in	the	KEYSTONE	adjustment	are	reset	to	initial	values
TIP:
Adjustable	range	of	the	KEYSTONE	and	the	CORNERSTONE:
Horizontal	DirectionVertical	Direction
CORNERSTONEApprox.	±10°	(Max)Approx.	±10°	(Max)KEYSTONE
Adjustable	range	may	be	narrower	depending	on	input	signal. 
						

							33
3. Convenient Features
 Preventing the Unauthorized Use of the Projector [SECURITY]
A	keyword	 can	be	set	 for	your	 projector	 using	the	Menu	 to	avoid	 operation	 by	an	 unauthorized	 user.	When	 a	keyword	
is	 set,	 turning	 on	the	 projector	 will	display	 the	Keyword	 input	screen. 	Unless	 the	correct	 keyword	 is	entered,	 the	pro-
jector	cannot	project	an	image. 	
•	 The	[SECURITY]	setting	cannot	be	cancelled	by	using	the	[RESET]	of	the	menu.
To	enable	the	Security	function:
1. Press the MENU button.
  The menu will be displayed.
2. Press the 	button	 twice	to	select	 [SETUP]	 and	press	 the		button	 or	the	 ENTER	 button	to	select	 [GEN-
ERAL].
3.  Press the 	button	to	select	[INSTALLATION].
4.  Press the 	button	three	times	to	select	[SECURITY]	and	press	the	ENTER	button.
  The OFF/ON menu will be displayed.
5.  Press the 	button	to	select	[ON]	and	press	the	ENTER	button.
	 The	[SECURITY	KEYWORD]	screen	will	be	displayed.
6. Type in a combination of the four  buttons and press the ENTER button.
NOTE:	A	keyword	must	be	4	to	10	digits	in	length.
	 The	[CONFIRM	KEYWORD]	screen	will	be	displayed. 
						

							34
3. Convenient Features
7. Type in the same combination of  buttons and press the ENTER button.
  The confirmation screen will be displayed.
8.	 Select	[YES]	and	press	the	ENTER	button.
	 The	SECURITY	function	has	been	enabled.
To	turn	on	the	projector	when	[SECURITY]	is	enabled:
1. Press the POWER button.
	 The	projector	will	be	turned	on	and	display	a	message	to	the	effect	that	the	projector	is	locked.
2.  Press the MENU button.
3.  Type in the correct keyword and press the ENTER button. The projector will display an image.
NOTE:	The	security	disable	mode	is	maintained	until	the	main	power	is	turned	off	or	unplugging	the	power	cord. 
						

							35
3. Convenient Features
To	disable	the	SECURITY	function:
1. Press the MENU button.
  The menu will be displayed.
2.		Select	[SETUP]	→	[INSTALLATION]	→	[SECURITY]	and	press	the	ENTER	button.
  The OFF/ON menu will be displayed.
3.	 Select	[OFF]	and	press	the	ENTER	button.
	 The	SECURITY	KEYWORD	screen	will	be	displayed.
4. Type in your keyword and press the ENTER button.
	 When	the	correct	keyword	is	entered,	the	SECURITY	function	will	be	disabled.
NOTE:	 If	you	 forget	 your	keyword,	 contact	your	dealer.	 Your	dealer	 will	provide	 you	with	 your	 keyword	 in	exchange	 for	your	 request	
code.	 Your	request	 code	is	displayed	 in	the	 Keyword	 Confirmation	 screen.	In	this	 example	 [NB52-YGK8-2VD6-K585-JNE6-EYA8]	
is	a	request	code. 
						

							36
3. Convenient Features
 Using the Computer Cable (VGA) to Operate the 
Projector (Virtual Remote Tool)
Using	the	utility	 software	 “Virtual	Remote	 Tool”	included	 on	the	 companion	 NEC	Projector	 CD-ROM,	 Virtual	Remote	
screen	(or	toolbar)	can	be	displayed	on	your	computer	screen.
This	will	help	 you	perform	 operations	 such	as	projector’s	 power	on	or	off	 and	 signal	 selection	 via	the	 computer	 cable	
(VGA),	serial	cable,	 or	LAN	 connection. 	Only	 via	serial	 or	LAN	 connection	 it	is	 also	 used	 to	send	 an	image	 to	the	
projector	 and	register	 it	as	 the	 logo	 data	 of	the	 projector. 	After	 registering	 it,	you	 can	 lock	 the	logo	 to	prevent	 it	from	
changing.
Control	Functions
Power	 On/Off,	 signal	selection,	 picture	freeze,	 picture	mute,	audio	mute,	 Logo	transfer	 to	the	 projector,	 and	remote	
control	operation	on	your	PC.
Virtual	Remote	screenToolbar
This	section	provides	an	outline	of	preparation	for	use	of	 Virtual	Remote	Tool.
For	information	on	how	to	use	 Virtual	Remote	Tool,	see	Help	of	 Virtual	Remote	Tool.	(→	page	41)
Step	1: 	Install	Virtual	Remote	 Tool	on	the	computer. 	(→	page	37)
Step	2:	Connect	the	projector	to	the	computer. 	(→	page	39)
Step	3:	Start	Virtual	Remote	 Tool.	(→	page	40)
TIP:
•	 Virtual	Remote	Tool	can	be	used	with	a	LAN	and	a	serial	connection.	USB	connection	is	not	supported	by	Virtual	Remote	Tool.
•	 For	update	information	on	Virtual	Remote	Tool,	visit	our	website:	
	 http://www.nec-display.com/dl/en/index.html 
						

							37
3. Convenient Features
NOTE:
•	 When	[COMPUTER]	 is	selected	 from	your	source	 selection,	 the	Virtual	 Remote	 screen	or	the	 toolbar	 will	be	displayed	 as	well	 as	
your	computer	screen.
•	 Use	 the	supplied	 computer	 cable	(VGA)	 to	connect	 the	COMPUTER	 IN	terminal	 directly	with	the	monitor	 output	terminal	 of	the	
computer	to	use	Virtual	Remote	Tool.
	 Using	a	switcher	or	other	cables	than	the	supplied	computer	cable	(VGA) 	may	cause	failure	in	signal	communication.
	 VGA	cable	terminal:
	 Pin	Nos.	12	and	15	are	required	for	DDC/CI.
•	 Virtual	Remote	Tool	may	not	work	depending	on	your	computer’s	specifications	and	version	of	graphic	adapters	or	drivers.
•	 To	run	Virtual	 Remote	 Tool	on	Windows	 8.1,	Windows	 8	and	 Windows	 XP,	“Microsoft	 .NET	Framework	 Version	2.0”	is	required.	
The	 Microsoft	 .NET	Framework	 Version	2.0,	3.0	or	3.5	 is	available	 from	Microsoft’s	 web	page.	 Download	 and	install	 it	on	 your	
computer.
•	 Logo	data	(graphics)	that	can	be	sent	to	the	projector	with	Virtual	Remote	Tool	has	the	following	restrictions:	
	 (Only	via	serial	or	LAN	connection)
-	 File	size:	Less	than	1	MB
-	 Image	size	(resolution):	
	 UM361X/UM301X:	Horizontal	1024	×	vertical	768	dots	or	less
	 UM351W/UM301W:	Horizontal	1280	×	vertical	800	dots	or	less
-	 Number	of	colors:	256	colors	or	less
•	 To	 put	the	default	 "NEC	logo"	 back	in	the	 background	 logo,	you	need	 to	register	 it	as	 the	 background	 logo	by	using	 the	image	 file	
(UM351W/UM301W:	 /Logo/necpj_bbwx.bmp,	 UM361X/UM301X:	/Logo/necpj_bb_x.bmp)inclulded	 on	the	 supplied	 NEC	Projector 	
CD-ROM.
TIP:
•	 The	 projector’s	 COMPUTER	 IN	terminal	 supports	 DDC/CI	(Display	 Data	Channel	 Command	 Interface).	DDC/CI	is	a	standard	
interface	for	bidirectional	communication	between	display/projector	and	computer.
Step 1: Install Virtual Remote Tool on the computer
NOTE:
•	 To 	install 	Virtual 	Remote 	Tool, 	the 	Windows 	user 	account 	must 	have 	“Administrator” 	privilege 	(Windows 	8.1, 	Windows 	8, 	Windows	
7,	and	Windows	Vista)	or	"Computer	Administrator"	privilege	(Windows	XP).	
•	 Exit	 all	running	 programs	 before	installing	 Virtual	Remote	 Tool.	If	another	 program	 is	running,	 the	installation	 may	not	be	com-
pleted.	
1	 Insert	the	accompanying	NEC	Projector	CD-ROM	into	your	CD-ROM	drive.
  The menu window will be displayed. 
						

							38
3. Convenient Features
TIP:
If	the	menu	window	will	not	be	displayed,	try	the	following	procedure.
For	Windows	7
1.	 Click	“start”	on	Windows.
2.	 Click	 “All	Programs” 	→	“Accessories” 	→	“Run”.
3.	 Type 	your 	CD-ROM 	drive 	name 	(example: 	“Q:\”) 	and 	“LAUNCHER.EXE” 	in 	“Name”. 	(example: 	Q:\
LAUNCHER.EXE)
4.	 Click	 “OK”.
 The menu window will be displayed.
2	 Click	 “Install	Virtual	Remote	 Tool”	on	the	menu	window.
 The installation will start.
 When the installation is complete, the Welcome window will be displayed.
3	 Click	 “Next”.
	 “END	USER	LICENSE	AGREEMENT” 	screen	will	be	displayed.
	 Read	“END	USER	LICENSE	AGREEMENT” 	carefully.
4	 If	you	agree,	click	“I	accept	the	terms	in	the	license	agreement” 	and	then	click	“Next”.
•	 Follow	the	instructions	on	the	installer	screens	to	complete	the	installation.
•	 When	the	installation	is	complete,	you	will	return	to	the	menu	window. 
						

							39
3. Convenient Features
TIP:
Uninstalling	Virtual	Remote	 Tool
Preparation:
Exit	Virtual	 Remote	 Tool	before	 uninstalling. 	To	 uninstall	 Virtual	Remote	 Tool,	the	Windows	 user	account	 must	have	
“Administrator” 	privilege	 (Windows	 8.1,	Windows	 8,	Windows	 7	and	 Windows	 Vista)	or	“Computer	 Administrator” 	
privilege	(Windows	XP).
•	For	Windows	8.1, 	Windows	8, 	Windows	7	and	 Windows	Vista
1	 Click	“Start”	and	then	 “Control	Panel”.
 The Control Panel window will be displayed.
2	 Click	 “Uninstall	a	program” 	under	“Programs”
	 The	“Programs	and	Features” 	window	will	be	displayed.
3	 Select	Virtual	Remote	 Tool	and	click	it.
4	 Click	“Uninstall/Change” 	or	“Uninstall”.
	 •	 When	the	 “User	Account	Control” 	windows	is	displayed,	click	 “Continue”.
 Follow the instructions on the screens to complete the uninstallation.
•	For	 Windows	XP
1	 Click	 “Start”	and	then	 “Control	Panel”.
 The Control Panel window will be displayed.
2	 Double-click	 “Add	/	Remove	Programs”.
 The Add / Remove Programs window will be displayed.
3	 Click	 Virtual	Remote	 Tool	from	the	list	and	then	click	 “Remove”.
 Follow the instructions on the screens to complete the uninstallation.
Step 2: Connect the projector to the computer
1	 Use	 the	supplied	 computer	 cable	(VGA)	 to	connect	 the	COMPUTER	 IN	terminal	 of	the	 projector	 directly	
with the monitor output terminal of the computer.
2	 Connect	the	supplied	power	cord	to	the	AC	IN	of	the	projector	and	the	wall	outlet.
 The projector is in the standby condition.
AC	Input Supplied computer cable (VGA)
→ To wall outlet
Power cord (supplied)
TIP:
•	 When	Virtual	Remote	Tool	starts	for	the	first	time,	“Easy	Setup”	window	will	be	displayed	to	navigate	your	connections.