NEC Projector UM301X User Manual

90
5. Using On-Screen Menu
[INSTALLATION]
Selecting	Projector	Orientation	[ORIENTATION]
This	reorients	 your	image	 for	your	 type	of	projection. 	The	 options	 are:	desktop	 front	projection,	 ceiling	rear	projection,	
desktop	rear	projection,	and	ceiling	front	projection.
AUTO
When	 the	lamp	 is	turned	 ON,	the	inner	 sensor	 of	the	 projector	 detects	its	installation	 state	either	 DESK	 FRONT	 or	
CEILING	FRONT	and	then	switch	its	projection	method
DESKTOP	FRONTCEILING	REAR
DESKTOP	REARCEILING...

91
5. Using On-Screen Menu
Selecting	Communication	Speed	[COMMUNICATION	SPEED]
This	feature	 sets	the	baud	 rate	of	the	 PC	Control	 port	(D-Sub	 9P).	It	 supports	 data	rates	 from	4800	 to	38400	 bps.	The	
default	 is	38400	 bps.	Select	 the	appropriate	 baud	rate	for	your	 equipment	 to	be	 connected	 (depending	 on	the	 equip-
ment,	a	lower	baud	rate	may	be	recommended	for	long	cable	runs).
NOTE:	Your	selected	communication	speed	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
Setting...

92
5. Using On-Screen Menu
Using	Test	Pattern	[TEST	PATTERN]
Displays	 the	test	 pattern	 to	check	 for	image	 distortion	 at	the	 time	 of	the	 projector	 setup.	Press	 the	ENTER	 button	to	
display	 the	test	 pattern; 	press	 the	EXIT	 button	 to	close	 the	test	 pattern	 and	return	 to	the	 menu. 	Menu	 operation	 and	
corrections	for	keystone,	cornerstone	and	pincushion	are	not	available	when	the	test	pattern	is	displayed.
Selecting	Microphone	 Type	[MIC	SELECT]
This	feature	allows	you	to	select...

93
5. Using On-Screen Menu
lamp	to	overcool,	causing	the	image	to	flicker.	Switch	[FAN	MODE]	to	[AUTO].
•	 Using	the	projector	 at	altitudes	 approximately	 5500	feet/1700	 meters	or	higher	 can	shorten	 the	life	of	optical	 components	 such	
as	the	lamp.
•	 Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
TIP:	
•	 When	[HIGH	ALTITUDE]	is	selected,	an	icon	[		]	is	displayed	at	the	bottom	of	the	on-screen	menu.
Selecting	Signal	Format	[SIGNAL	SELECT]
[COMPUTER]
Allows	you	to...

94
5. Using On-Screen Menu
USB-B ��������������������Select [USB-B] or [COMPUTER] to switch the source connected over the USB cable (USB-B)�
Enabling	Key	Sound	and	Error	Sound	[BEEP]
This	 feature	 turns	on	or	off	 the	 button	 sound	or	alarm	 when	an	error	 occurs	 or	the	 following	 operations	 are	per-
formed.
-	Displaying	the	main	menu	
-	Switching	sources
-	Resetting	data	by	using	[RESET]
-	Pressing	POWER	ON	or	STANDBY	button
[OPTIONS(2)]
Selecting	Power-saving	in	[STANDBY	MODE]
The	projector	has...

95
5. Using On-Screen Menu
Turning	On	the	Projector	By	Applying	Computer	Signal	[AUTO	POWER	ON]
When	the	projector	 is	in	 Standby	 mode,	applying	 a	computer	 or	HDMI	 signal	 from	a	computer	 connected	 to	the	 COM-
PUTER	IN	input,	HDMI1/MHL,	or	HDMI2	input	will	power	on	the	projector	and	simultaneously	project	the	image.
This	 functionality	 eliminates	the	need	 to	always	 use	the	POWER	 button	on	the	 remote	 control	or	the	 projector	 cabinet	
to	power	on	the	projector.
To	use	this	function,	first...

96
5. Using On-Screen Menu
Setting up the Projector for a Wired LAN Connection [WIRED LAN]
Important
•	 Consult	with	your	network	administrator	about	these	settings.
•	 When	using	a	wired	 LAN	connection,	 connect	a	LAN	 cable	 (Ethernet	 cable)	to	the	 LAN	 port	(RJ-45)	 of	the	 projec-
tor.	(→	page	114)
TIP:	The	network	settings	you	make	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
[WIRED	LAN][DISABLE]Wired	LAN	connection	will	be	turned	off.
[ENABLE]Wired	LAN	connection	will	be	turned...

97
5. Using On-Screen Menu
Setting up the Projector for a Wireless LAN Connection (with the optional USB Wireless 
LAN Unit equipped) [WIRLESS LAN]
Important
•	 Consult	with	your	network	administrator	about	these	settings.
•	 When	using	a	wireless	LAN	connection,	attach	the	optional	USB	Wireless	LAN	to	the	projector.	(→	page	115)
[PROFILE][DISABLE]Wireless	LAN	connection	will	be	turned	off
[SIMPLE	ACCESS	
POINT]
Set	the	projector	for	simple	access	point.
Selecting	[SIMPLE	ACCESS	 POINT]	will	allow	 the...

98
5. Using On-Screen Menu
Hints	on	How	to	Set	Up	LAN	Connection
To	set	up	the	projector	for	a	LAN	connection:
Access	the	HTTP	 server	 function	 to	display	 the	web	 browser	 (→	page	45)	 and	 select	 [NETWORK	 SETTINGS]	→ 
[SETTINGS]	→	[WIRELESS	LAN]	→	[PROFILE	1]	or	[PROFILE	2].
Two	settings	can	be	set	for	the	USB	 Wireless	LAN	Unit.
Next	select	 [SETTINGS]	 for	your	 selected	 profile,	and	set	[ENABLE]	 or	[DISABLE]	 for	[DHCP],	 [IP	ADDRESS],	
[SUBNET	 MASK],	and	[GATEWAY]. 	Last	 click	 [SAVE]. 	To...

99
5. Using On-Screen Menu
 Menu Descriptions & Functions [INFO.]
Displays	the	status	 of	the	 current	 signal	and	lamp	 usage. 	This	 item	has	six	pages. 	The	 information	 included	is	as	
follows:
TIP:	Pressing	the	HELP	button	on	the	remote	control	will	show	the	[INFO.]	menu	items.
[USAGE TIME]
[LAMP	LIFE	REMAINING]	(%)*
[LAMP	HOURS	USED]	(H)
[FILTER	HOURS	USED]	(H)
[TOTAL	CARBON	SAVINGS]	(kg-CO2)
[TOTAL	COST	SAVINGS]
*	 The	progress	indicator	shows	the	percentage	of	remaining	bulb	life.
	 The	 value...