NEC Projector Um280x User Manual

							91
5. Using On-Screen Menu
Selecting	Communication	Speed	[COMMUNICATION	SPEED]
This	feature	 sets	the	baud	 rate	of	the	 PC	Control	 port	(D-Sub	 9P).	It	 supports	 data	rates	 from	4800	 to	38400	 bps.	The	
default	 is	38400	 bps.	Select	 the	appropriate	 baud	rate	for	your	 equipment	 to	be	 connected	 (depending	 on	the	 equip-
ment,	a	lower	baud	rate	may	be	recommended	for	long	cable	runs).
NOTE:	Your	selected	communication	speed	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
Setting	ID	to	the	Projector	[CONTROL	ID]
You	can 	operate 	multiple 	projectors 	separately 	and 	independently 	with 	the 	single 	remote 	control 	that 	has 	the 	CONTROL	
ID	 function. 	If	 you	 assign	 the	same	 ID	to	all	 the	 projectors,	 you	can	 conveniently	 operate	all	the	 projectors	 together	
using	the	single	remote	control. 	To	do	so,	you	have	to	assign	an	ID	number	to	each	projector.
CONTROL ID NUMBER �������Select a number from 1 to 254 you wish to assign to your projector �
CONTROL ID �����������������������Select [OFF] to turn off the CONTROL ID setting and select [ON] to turn on the CONTROL ID set -
ting�
NOTE:	
•	 When	[ON]	is	selected	 for	[CONTROL	 ID],	the	projector	 cannot	be	operated	 by	using	 the	remote	 control	that	does	 not	support	
the	CONTROL	ID	function.	(In	this	case	the	buttons	on	the	projector	cabinet	can	be	used.)
•	 Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
•	 Pressing	 and	holding	 the	ENTER	 button	on	the	 projector	 cabinet	for	10	seconds	 will	display	 the	menu	 for	canceling	 the	Control	
ID.
Assigning	or	Changing	the	Control	ID
1. Turn on the projector.
2.	 Press	the	ID	SET	button	on	the	remote	control.
	 The	CONTROL	ID	screen	will	be	displayed.
	 If	 the	projector	 can	be	operated	 with	the	current	 remote	control	ID,	the	 [ACTIVE]	 will	be	displayed. 	If	 the	 projector	
cannot	 be	operated	 with	the	current	 remote	control	ID,	the	 [INACTIVE]	 will	be	displayed. 	To	 operate	 the	inactive	
projector,	assign	the	control	ID	used	for	the	projector	by	using	the	following	procedure	(Step	3).
3.	 Press	 one	of	numeric	 keypad	buttons	 while	pressing	 and	holding	 the	ID	SET	
button on the remote control.
 Example:
	 To	assign	 “3”,	press	the	 “3”	button	on	the	remote	control.
	 No	 ID	means	 that	all	the	 projectors	 can	be	operated	 together	with	a	single	 remote	
control. 	To	set	 “No	ID”,	enter	 “000”	or	press	the	CLEAR	button.
TIP:	The	range	of	IDs	is	from	1	to	254.
4.	 Release	the	ID	SET	button.
	 The	updated	CONTROL	ID	screen	will	be	displayed.
NOTE:	
•	 The	IDs	can	be	cleared	in	a	few	days	after	the	batteries	are	run	down	or	removed.
•	 Accidentally	 pressing	any	one	 of	the	 buttons	 of	the	 remote	 control	will	clear	 currently	 specified	
ID	with	batteries	removed. 
						

							92
5. Using On-Screen Menu
Using	Test	Pattern	[TEST	PATTERN]
Displays	 the	test	 pattern	 to	check	 for	image	 distortion	 at	the	 time	 of	the	 projector	 setup.	Press	 the	ENTER	 button	to	
display	 the	test	 pattern; 	press	 the	EXIT	 button	 to	close	 the	test	 pattern	 and	return	 to	the	 menu. 	Menu	 operation	 and	
keystone	correction	are	not	possible	when	the	test	pattern	is	displayed.
Setting	MIC	Gain	[MIC	GAIN]
This	feature	 allows	you	to	adjust	 your	microphone	 sensitivity	when	it	is	 connected	 to	the	 MIC	 input	 jack	of	the	 projec-
tor.	Microphone	 volume	can	be	adjusted	 with	the	VOL. 	(+)	 or	(−)	 button	 on	the	 remote	 control	or	the	 or   on the 
projector	cabinet.
[OPTIONS(1)]
Setting	Auto	Adjust	[AUTO	ADJUST]
This	feature	 sets	the	Auto	 Adjust	 mode	so	that	 the	computer	 signal	can	be	automatically	 or	manually	 adjusted	for	
noise	and	stability. 	You	can	automatically	make	adjustment	in	two	ways: 	[NORMAL]	and	[FINE].
OFF ������������������������The computer signal will not be automatically adjusted� You can manually optimize the computer signal�
NORMAL ����������������Default setting� The computer signal will be automatically adjusted� Normally select this option�
FINE  �����������������������Select this option if fine adjustment is needed� It takes more time to switch to the source than when [NOR-
MAL]is selected�
Selecting	Fan	Mode	[FAN	MODE]
This	option	allows	you	to	select	three	modes	for	fan	speed: 	Auto	mode,	High	speed	mode,	and	High	Altitude	mode.
AUTO ���������������������The built-in fans automatically run at a variable speed according to the\
 internal temperature�
HIGH ����������������������The built-in fans run at high speed�
HIGH ALTITUDE  �����The built-in fans run at a high speed� Select this option when using the projector at altitudes approximately 
5500 feet/1700 meters or higher �
When	you	wish	to	cool	down	the	temperature	inside	the	projector	quickly,	select	[HIGH].
NOTE:	
•	 It	is	recommended	that	you	select	High	speed	mode	if	you	use	the	projector	non-stop	for	consecutive	days.
•	 Set	[FAN	MODE]	to	[HIGH	ALTITUDE]	when	using	the	projector	at	altitudes	approximately	5500	feet/1700	meters	or	higher.
•	 Using	the	projector	 at	altitudes	 approximately	 5500	feet/1700	 meters	or	higher	 without	 setting	to	[HIGH	 ALTITUDE]	 can	cause	
the	projector	to	overheat	and	the	protector	could	shut	down.	If	this	happens,	wait	a	couple	minutes	and	turn	on	the	projector.
•	 Using	 the	projector	 at	altitudes	 less	than	 approximately	 5500	feet/1700	 meters	and	setting	 to	[HIGH	 ALTITUDE]	 can	cause	 the	
lamp	to	overcool,	causing	the	image	to	flicker.	Switch	[FAN	MODE]	to	[AUTO].
•	 Using	 the	projector	 at	altitudes	 approximately	 5500	feet/1700	 meters	or	higher	 can	shorten	 the	life	of	optical	 components	 such	
as	the	lamp.
•	 Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
TIP:	
•	 When	[HIGH	ALTITUDE]	is	selected,	an	icon	[		]	is	displayed	at	the	bottom	of	the	on-screen	menu. 
						

							93
5. Using On-Screen Menu
Selecting	Signal	Format	[SIGNAL	SELECT]
[COMPUTER]
Allows	you	to	choose	 [COMPUTER]	 for	an	RGB	 source	 such	as	a	computer,	 or	[COMPONENT]	 for	a	component	
video	 source	 such	as	a	DVD	 player. 	Normally	 select	[RGB/COMPONENT]	 and	the	projector	 automatically	 detects	a	
component	 signal.	However	 there	may	be	some	 component	 signals	that	the	projector	 is	unable	 to	detect. 	If	 this	 is	the	
case,	select	[COMPONENT].
[VIDEO	&	S-VIDEO	System	Select]
This	feature	enables	you	to	select	composite	video	standards	automatically	or	manually.
Normally	select	[AUTO]	and	the	projector	will	automatically	detect	the	video	standard.
In	 the	 case	 where	 the	projector	 has	difficulty	 detecting	 the	video	 standard,	 select	the	appropriate	 video	standard	 from	
the menu.
This	must	be	done	for	 VIDEO	and	S-VIDEO	respectively.
Enabling	or	Disabling	 WXGA	Mode	[WXGA	MODE]
Selecting	[ON]	will	give	 priority	 to	WXGA	 (1280	×	768)/WUXGA	 (1920	×	1200)	 signals	 in	recognizing	 an	input	 sig-
nal.
When	 [WXGA	 MODE]	is	set	 to	[ON],	 XGA	(1024	 ×	768)/UXGA	 (1600	×	1200)	 signals	 may	not	be	recognized	 on	
UM330X/UM280X. 	In	this	case,	select	[OFF].
NOTE:	
•	 The	[OFF]	is	selected	at	the	time	of	shipment	of	UM330X/UM280X.
•	 The	[ON]	is	selected	at	the	time	of	shipment	of	UM330W/UM280W.
Enabling	the	deinterlace	[DEINTERLACE]
Turns	on	or	off	the	deinterlace	function	for	a	telecine	signal.
OFF ������������������������Select this option if there is any jitter or artifacts in video�
ON  �������������������������Default standard setting�
NOTE:	This	feature	is	not	available	for	HDTV	(progressive)	and	computer	signals.
Setting	HDMI1/2	[HDMI	SETTINGS]
Make	the	settings	for	each	video	level	and	audio	level	when	connecting	HDMI	equipment	such	as	a	DVD	player. 	
VIDEO LEVEL ���������Select [AUTO] to automatically detect video level� If automatic detection may not work well, select [NOR-
MAL] to disable the [ENHANCED] feature of your HDMI equipment or select [ENHANCED] to improve image 
contrast and increase detail in the dark areas�
AUDIO SELECT  ������Select [HDMI1] or [HDMI2] to switch the HDMI 1 or HDMI 2 IN digital audio signal and select [COMPUTER] 
to switch the COMPUTER input audio signal�
Enabling	Key	Sound	and	Error	Sound	[BEEP]
This	 feature	 turns	on	or	off	 the	 button	 sound	or	alarm	 when	an	error	 occurs	 or	the	 following	 operations	 are	per-
formed.
-	Displaying	the	main	menu	
-	Switching	sources
-	Resetting	data	by	using	[RESET]
-	Pressing	POWER	ON	or	POWER	OFF	button 
						

							94
5. Using On-Screen Menu
[OPTIONS(2)]
Selecting	Power-saving	in	[STANDBY	MODE]
The	projector	has	two	standby	modes:	[NORMAL]	and	[POWER-SAVING].
The	POWER-SAVING	 mode	is	the	 mode	 that	allows	 you	to	put	 the	projector	 in	the	 power-saving	 condition	which	
consumes	less	power	than	the	NORMAL	mode. 	The	projector	is	preset	for	NORMAL	mode	at	the	factory.
NORMAL ����������������Power indicator: Orange light/STATUS indicator: Green light
POWER-SAVING
  ����Power indicator: Red light/STATUS indicator: Off
The following connectors, buttons or functions will not work during this\
 mode�
- MONITOR OUT (COMP �) connector, and AUDIO OUT connector
- LAN and Mail Alert functions
- Buttons other than POWER button on the cabinet
- Buttons other than POWER ON button on the remote control
- Virtual Remote Tool, USB Display fucntion
NOTE:	
•	 When	[CONTROL	 PANEL	LOCK],	 [CONTROL	 ID],	or	[AUTO	 POWER	 ON(COMP.)]	 is	turned	 on,	the	[STANDBY	 MODE]	setting	is	
not	available.
•	 Even	when	[POWER-SAVING]	is	selected	for	[STANDBY	MODE],	power	on	or	off	can	be	done	by	using	the	PC	CONTROL	port.
•	 The	power	consumption	in	the	standby	mode	will	not	be	included	in	calculating	CO2	emission	reduction.
•	 Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
Enabling	Direct	Power	On	[DIRECT	POWER	ON]
Turns	the	projector	 on	automatically	 when	the	power	 cord	is	inserted	 into	an	active	 power	 outlet.	This	 eliminates	 the	
need	to	always	use	the	POWER	button	on	the	remote	control	or	projector	cabinet. 
						

							95
5. Using On-Screen Menu
Turning	On	the	Projector	By	Applying	Computer	Signal	[AUTO	POWER	ON(COMP.)]
When	the	projector	 is	in	 Standby	 mode,	applying	 a	computer	 signal	from	a	computer	 connected	 to	the	 COMPUTER	
IN	input	will	power	on	the	projector	and	simultaneously	project	the	computer’s	image.
This	 functionality	 eliminates	the	need	 to	always	 use	the	POWER	 button	on	the	 remote	 control	or	the	 projector	 cabinet	
to	power	on	the	projector.
To	use	this	function,	first	connect	a	computer	to	the	projector	and	the	projector	to	an	active	AC	input.
NOTE:	
•	 Disconnecting	 a	computer	 signal	from	the	computer	 will	not	power	 off	the	 projector.	 We	recommend	 using	this	function	 in	com-
bination	of	the	AUTO	POWER	OFF	function.
•	 This	function	will	not	be	available	under	the	following	conditions:
-	 when	a	component	signal	is	applied	to	the	COMPUTER	IN	connector
-	 when	a	Sync	on	Green	RGB	signal	or	composite	sync	signal	is	applied
•	 To	enable	the	AUTO	POWER	ON(COMP.)	after	turning	off	the	projector,	wait	3	seconds	and	input	a	computer	signal.
	 If	 a	computer	 signal	is	still	 present	 when	the	projector	 is	turned	 off,	the	AUTO	 POWER	 ON(COMP.)	 will	not	work	 and	the	projector	
remains	in	standby	mode.
Enabling	Power	Management	[AUTO	POWER	OFF]
When	 this	option	 is	selected	 you	can	 enable	 the	projector	 to	automatically	 turn	off	(at	 the	 selected	 time:	5min.,	 10min.,	
20min.,	30min.,	60min.)	if	there	is	no	signal	received	by	any	input	or	if	no	operation	is	performed.
Selecting	Default	Source	[DEFAULT	SOURCE	SELECT]
You	can	set	the	projector	to	default	to	any	one	of	its	inputs	each	time	the	projector	is	turned	on.
LAST ����������������������Sets the projector to default to the previous or last active input each \
time the projector is turned on�
AUTO  ���������������������Searches for an active source in order of COMPUTER  → HDMI1  → HDMI2  → VIDEO  → S-VIDEO  → VIEWER 
→ USB DISPLAY →
 COMPUTER and displays the first found source�
COMPUTER  �����������Displays the computer signal from the COMPUTER IN connector every time the projector is turned on�
HDMI1 �������������������Displays the digital source from the HDMI 1 IN connector every time the projector is turned on� 
HDMI2 �������������������Displays the digital source from the HDMI 2 IN connector every time the projector is turned on�
VIDEO ��������������������Displays the Video source from the VIDEO IN connector every time the projector is turned on�
S-VIDEO  ����������������Displays the Video source from the S-VIDEO IN connector every time the projector is turned on�
VIEWER �����������������Displays slides or plays back movie files from the USB memory device every time the projector is turned 
on�
NETWORK  �������������Displays a signal from LAN port (RJ-45) or the USB Wireless LAN Unit�
USB DISPLAY ��������Displays the computer signal from the USB (PC) port every time the projector is turned on� 
						

							96
5. Using On-Screen Menu
Setting up the Projector for a Wired LAN Connection [WIRED LAN]
Important
•	 Consult	with	your	network	administrator	about	these	settings.
•	 When	using	a	wired	 LAN	connection,	 connect	a	LAN	 cable	 (Ethernet	 cable)	to	the	 LAN	 port	(RJ-45)	 of	the	 projec-
tor.	(→	page	112)
TIP:	The	network	settings	you	make	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
[WIRED	LAN][DISABLE]Wired	LAN	connection	will	be	turned	off.
[ENABLE]Wired	LAN	connection	will	be	turned	on.
[SETTINGS] [DHCP]
ON ��������������������������IP address, subnet mask, and gateway will 
be  automatically  assigned  to  the  projector 
from your DHCP server �
OFF �������������������������Specify IP address, subnet mask, and gate-
way  assigned  by  your  network  administra-
tor �
[IP	ADDRESS]Set 	your 	IP 	address 	of 	the 	network 	connected 	to 	the	
projector.
[SUBNET	MASK]Set	 your	 subnet	 mask	number	 of	the	 network	 connected	
to	the	projector.
[GATEWAY]Set	the	default	 gateway	 of	the	 network	 connected	 to	the	
projector.
[AUTO	DNS]ON ��������������������������DHCP  server  will  automatically  assign  IP 
address  of  DNS  server  connected  to  the 
projector �
OFF �������������������������Set your IP address of DNS server connected 
to the projector � 
						

							97
5. Using On-Screen Menu
Setting up the Projector for a Wireless LAN Connection (with the optional USB Wireless 
LAN Unit equipped) [WIRLESS LAN]
Important
•	 Consult	with	your	network	administrator	about	these	settings.
•	 When	using	a	wireless	LAN	connection,	attach	the	optional	USB	Wireless	LAN	to	the	projector.	(→	page	113)
[PROFILE][DISABLE]Wireless	LAN	connection	will	be	turned	off
[EASY	CONNECTION]Select	[EASY	 CONNECTION]	 to	execute	 a	wireless	 LAN	
easily	using	Image	 Express	 Utility	Lite	on	the	 supplied	
NEC	Projector	CD-ROM.
[PROFILE	1]Up	to	two	 settings	 for	the	 USB	 wireless	 LAN	unit	can	be	
stored	in	memory	of	the	projector. 	(→	page	46)
To	recall	 the	settings	 from	memory,	 select	[PROFILE	 1]	or	
[PROFILE	2]	from	[PROFILE].
[PROFILE	2]
[RECONNECT]Retry	to	connect	the	projector	to	a	network. 	Try	this	if	you	have	changed	[PROFILE].
NOTE: 	After 	selecting 	[EASY 	CONNECTION] 	from 	[PROFILE], 	you 	cannot 	make 	settings 	to 	[DHCP], 	[IP 	ADDRESS], 	[SUBNET 	MASK],	
[GATEWAY],	and	[AUTO	DNS]	except	[CHANNEL].	 
						

							98
5. Using On-Screen Menu
Hints	on	How	to	Set	Up	LAN	Connection
To	set	up	the	projector	for	a	LAN	connection:
Access	the	HTTP	 server	 function	 to	display	 the	web	 browser	 (→	page	43)	 and	 select	 [NETWORK	 SETTINGS]	→ 
[SETTINGS]	→	[WIRELESS	LAN]	→	[PROFILE	1]	or	[PROFILE	2].
Two	settings	can	be	set	for	the	USB	 Wireless	LAN	Unit.
Next	select	 [SETTINGS]	 for	your	 selected	 profile,	and	set	[ENABLE]	 or	[DISABLE]	 for	[DHCP],	 [IP	ADDRESS],	
[SUBNET	 MASK],	and	[GATEWAY]. 	Last	 click	 [SAVE]. 	To	 reflect	 changes,	 click	the	[SETTING]	 tab	and	 then	 click	
[APPLY]. 	(→	page	46)
To	recall	LAN	settings	stored	in	the	profile	number:
Use	[PROFILE	 1]	or	 [PROFILE	 2]	set	 on	the	 HTTP	 server,	 from	the	projector’ 	menu,	 select	[SETUP]	→	[WIRE-
LESS	 LAN]	→	[PROFILE]	→	[PROFILE	 1]	or	 [PROFILE	 2].	Last	 select	 [YES]	and	press	 the	ENTER	 button.	(→ 
page	97)
To connect a DHCP server:
From	 the	projector	 menu,	select	[SETUP]	→	[WIRED	 LAN]	→	[SETTINGS]	→	[DHCP]	→	[ON] 	and 	press 	the 	ENTER	
button. 	To	specify	IP	address	without	using	the	DHCP	server,	use	the	HTTP	server	function. 	(→	page	43)
To	set	only	for	wireless	LAN	(NETWORK	TYPE	and	WEP/WPA):
Access	the	HTTP	 server	 function	 to	display	 the	web	 browser	 (→	page	43)	 and	 select	 [NETWORK	 SETTINGS]	→ 
[SETTINGS]	→	[WIRELESS	LAN]	→	[PROFILE	1]	or	[PROFILE	2].
Make	necessary	settings	for	[SETTINGS]	and	click	[SAVE].
From	the	projector	menu,	select	[SETUP]	→	[WIRELESS	LAN]	→	[PROFILE]	→	[PROFILE	1]	or	[PROFILE	2]. 	
To	select	an	SSID:
Access	the	HTTP	 server	 function	 to	display	 the	web	 browser	 (→	page	43)	 and	 select	 [NETWORK	 SETTINGS]	→ 
[SETTINGS]	→	[WIRELESS	LAN]	→	[CONNECTION]	→	[SITE	SURVEY]	and	select	the	ID.
If	you	 do	not	 use	 [SITE	 SURVEY],	 type	the	SSID	 in	[CONNECTION]	 and	select	 [INFRASTRUCTURE]	 or	[AD	 HOC]. 	
(→	page	46)
To	receive	lamp	replacement	time	or	error	messages	via	e-mail:
Access	 the	HTTP	 server	 function	 to	display	 the	web	 browser	 (→	page	43)	 and	 select	 [NETWORK	 SETTINGS]	→ 
[ALERT	MAIL],	and	set	[SENDER’S	 ADDRESS],	 [SMTP	SERVER	 NAME],	and	[RECIPIENT’S	 ADDRESS].	Last,	
click	[SAVE]. 	(→	page	48)
To	execute	[EASY	CONNECTION]	using	Image	Express	Utility	Lite:
The	[EASY	 CONNECTION]	 is	a	mode	 that	can	abbreviate	 the	troublesome	 LAN	settings	 when	using	the	Image	
Express	Utility	Lite	and	connecting	the	PC	and	projector	via	a	wireless	LAN.
The	Image	Express	Utility	Lite	is	contained	on	the	supplied	NEC	Projector	CD-ROM. 	
To	use	 [EASY	 CONNECTION],	 access	the	HTTP	 server	 function	 to	display	 the	web	 browser	 (→	page	43)	 and	 select	
[NETWORK	 SETTINGS]	→	[SETTINGS]	→	[WIRELESS	 LAN]	→	[EASY	 CONNECTION]. 	Next	 select	 [SETTINGS]	
→	[CHANNEL]. 	Last	click	[SAVE].
From	the	projector	menu,	select	[SETUP]	→	[WIRELESS	LAN]	→	[PROFILE]	→	[EASY	CONNECTION]. 	 
						

							99
5. Using On-Screen Menu
 Menu Descriptions & Functions [INFO.]
Displays	the	status	 of	the	 current	 signal	and	lamp	 usage. 	This	 item	has	six	pages. 	The	 information	 included	is	as	
follows:
TIP:	Pressing	the	HELP	button	on	the	remote	control	will	show	the	[INFO.]	menu	items.
[USAGE TIME]
[LAMP	LIFE	REMAINING]	(%)*
[LAMP	HOURS	USED]	(H)
[FILTER	HOURS	USED]	(H)
[TOTAL	CARBON	SAVINGS]	(kg-CO2)
*	 The	progress	indicator	shows	the	percentage	of	remaining	bulb	life.
	 The	 value	informs	 you	of	the	 amount	 of	lamp	 usage. 	When	 the	remaining	 lamp	time	reaches	 0,	the	LAMP	 LIFE	
REMAINING	bar	indicator	changes	from	0%	to	100	Hours	and	starts	counting	down.
	 If	the	remaining	lamp	time	reaches	0	hours,	the	projector	will	not	turn	on.
•	 The	 message	 to	the	 effect	 that	the	lamp	 or	the	 filters	 should	 be	replaced	 will	be	displayed	 for	one	 minute	 when	
the	projector	is	turned	on	and	when	the	POWER	button	on	the	projector	or	the	remote	control	is	pressed.
	 To	dismiss	this	message,	press	any	button	on	the	projector	or	the	remote	control.
Lamp	life(H)
Replacement	lampModel
ECO MODEOFF/AUTO	ECONORMAL
ECO
3000 35006000NP17LP-UM UM330X/UM330W
4000 50008000NP16LP-UM UM280X/UM280W
•	
[TOTAL	CARBON	SAVINGS]
	 This	 displays	 the	estimated	 carbon	saving	information	 in	kg. 	The	 carbon	 footprint	 factor	in	the	 carbon	 saving	cal-
culation	is	based	on	the	OECD	(2008	Edition). 	(→	page	30) 
						

							100
5. Using On-Screen Menu
[SOURCE]
[SOURCE	NAME]	[SOURCE	INDEX]	
[HORIZONTAL	FREQUENCY]	 [VERTICAL	FREQUENCY]	
[SIGNAL	TYPE]	 [VIDEO	TYPE]	
[SYNC	TYPE]	 [SYNC	POLARITY]	
[SCAN	TYPE]
[WIRED LAN]
[IP	ADDRESS]	 [SUBNET	MASK]	
[GATEWAY]	 [MAC	ADDRESS]
[WIRELESS LAN]
[IP	ADDRESS]	[SUBNET	MASK]	
[GATEWAY]	 [MAC	ADDRESS]	
[SSID]	 [NETWORK	TYPE]	
[WEP/WPA]	 [CHANNEL]	
[SIGNAL	LEVEL]