NEC Projector Sx6000d User Manual

							E – 4
INPUT3RGB R/Cr
G/Y
B/Cb
H/HV
VR/Cr Cr
Y G/Y
B/Cb Cb
H/HV
V
OPTIONIN
OUT
REMOTE1
REMOTE2
INPUT7 INPUT8INPUT5
S-VIDEO1
Y
C
S-VIDEO2 VIDEO1 VIDEO2INPUT6
IN
OUT
INPUT2 INPUT1 INPUT4
56
1
2
3
4
910
8 7
1. INPUT 3 RGB Connector (Mini D-Sub 15 pin)
Connect your PC or other analog RGB equipment such as a high-defi-
nition document camera.
2. Option Connector (Mini D-Sub 9 pin)
For system expansion such as PC-control.
IN ................. connect to the external equipment such as PC.
OUT ............. for daisy-chaining multiple projectors and operating them with
the same external equipment. To do so, connect to a second
projectors IN terminal to relay the input at the IN terminal of
the first projector until all the projectors are connected.
3. REMOTE 1 Connector (Mini D-Sub 15 pin)
This terminal allows external control of the projector from either the
Switcher or from an external control. When the Switcher is used, con-
nect to the REMOTE 1 terminal on the back of the Switcher.
NOTE: This projector is compatible with the ISS-6020 Switcher.
4. REMOTE 2 Jacks
IN ................. wired remote control input.
OUT ............. for daisy-chaining multiple projectors and operating them with
the same remote control. To do so, connect to a second pro-
jector s IN terminal to relay the input at the IN terminal of the
first projector until all the projectors are connected.
5. INPUT 1 and INPUT 2 Terminals (BNC)
Connect R,G,B,H (Horizontal sync) and V (Vertical sync) outputs of the
external equipment such as the Switcher. If using a component with a
combined sync (SYNC) output, connect it to the H/V terminal.
Also connect component video outputs (Y/Cb/Cr) of the external equip-
ment such as DVD player.
NOTE: The INPUT 2 terminal does not support SW1 Level and SW2 Level modesfor the ISS-6020 switcher.
6. INPUT 4 Cr/Y/Cb Terminal (RCA)
Connect component video outputs (Y,Cb,Cr / Y,Pb,Pr) of the external
equipment such as DVD player.
NOTE: This terminal accepts component signal only.
7. INPUT 5 VIDEO 1 Terminal (BNC)
Connect to the BNC video output of the external equipment such as a
VCR or laser disk player.
8. INPUT 6 VIDEO 2 Terminal (RCA)
Connect to the RCA video output of the external equipment such as a
VCR or laser disk player.
9. INPUT 7 S-VIDEO 1 Terminal (BNC)
Connect to the Y/C separate BNC video outputs of the external equip-
ment such as a VCR or laser disk player.
10. INPUT 8 S-VIDEO 2 Terminal (Mini DIN 4 pin)
Connect to the S-video output of the external equipment such as a
VCR with an S-video output. This terminal allows switching between S2
and S1 VIDEO input modes. See the S-Video Mode Select section on
page E-38 for more information.
Terminal Panel 
						

							E – 5
OUTPUT OUTPUT
RGBDIGITAL
INPUT9 INPUT 0
SDI
11
aaaaaaaaaaaaaaaaaaaaaaa
11. RGB Digital Input/Output Connectors (DVI-D 24 pin)
These connectors are used for double or triple stacking.
Use the supplied DVI-D cable to connect the OUTPUT terminal of the
first projector to the second projectors INPUT until all the projectors
are connected.Push the left side of the panel to open the compartment for the
RGB Digital connectors and the optional SDI board.
Space to install the optional SDI or SX
HDSDI board.
(SX6000 only) 
						

							E – 6
OFF
+-
PICTUREADJUSTABC DEFGHI
JKL MNO PQR
STU
,.
UNDO CANCEL
TEST
PICTUREKEYSTONE AMPLITUDE ENTRYLISTSOUND OSD
MUTE
MAGNIFYHELP INFO.
POSITION AUTOPIXELVWX YZ/
WHITE BAL.IMAGE
ON POWER
MENU
ENTER
123
456
7
089
ADDRESS
PROJECTOR
RGB
LENS
SHUTTER
BS
+
-
+
-
FOCUSZOOM
CTLLENS
2
5
6
7
9
10
12
13
17
20
21
22
24
262
5
23
19
18
16
15
14
11 8 4 3 1
Remote Control
1 POWER ON
Press to turn on the projector. The POWER indicator lights up green.
2 POWER OFF
Press and hold this button for a minimum of two seconds to turn off the
projector.
3 MENU
Press to display the main menu.
While pressing and holding CTL, press this button to display the Re-
mote Control ID dialog box to specify the remote control ID.4 ENTER
Executes the menu selection and activates items selected from the menu.
When the slidebar or dialog box is diplayed:
Pressing this button confirms adjustments/setting and returns to the
previous menu display.
5 SELECT (Up/Down/Left/Right)
When pressed together, the CTL and 

 buttons work as a Back Space
key in the entry screen.
Pressing and holding CTL, then this button moves the menu, slidebar
or dialog box.
6 ADJUST WHITE BAL
Press to display the Color adjustment screen. Pressing this button se-
quentially selects Color Temperature → White Balance - Brightness
→ White Balance - Contrast → Signal Level → Ref.White Bal →
Switcher-Gain.
7 ADJUST PICTURE
Press to display the Picture adjustment screen. Pressing this button
sequentially selects Brightness → Contrast → Saturation → Color
→ Hue → Sharpness → V-Aperture → Gamma Correction.
8 IMAGE/PROJECTOR
Press to display the Image Option screen. Pressing this button sequen-
tially selects Pixel Adjust → Position → Aspect Ratio → Resolu-
tion → Overscan → Video Filter → Blanking.
While pressing and holding CTL, pressing this button rotates On/Off
Timer → Sleep Timer → Menu → Setup → Link Mode →
Switcher Control.
9 INPUT
Use to select an input, to name a signal, or to enter a passcode during
input registration.
1--INPUT 1 for RGBHV/Y, Cb/Pb, Cr/Pr
2--INPUT 2 for RGBHV/Y, Cb/Pb, Cr/Pr
3--INPUT 3 for RGB
4--INPUT 4 for Y, Cb/Pb, Cr/Pr
5--INPUT 5 for VIDEO 1
6--INPUT 6 for VIDEO 2
7--INPUT 7 for S-VIDEO 1
8--INPUT 8 for S-VIDEO 2
9--INPUT 9 for RGB DIGITAL input
0--INPUT 0 for SDI input on the optional SDI board
10 UNDO
Press to return the adjustments and settings to the previous condition.
While pressing and holding CTL, pressing this button clears all the menus
or ajustment/setting screen. At this time the adjustments/settings are
stored in memory.
11 CANCEL
Press to exit the menu.
Press this button with CTL to return to the previous menu while the
menus appear. This feature allows you to adjust several items concur-
rently.
12 INFO
Displays the Source Information or Projector Information window.
This button toggles between these two windows.
13 TEST
Press to display the test pattern. Pressing this button sequentially se-
lects five test patterns.
14 HELP
Provides online help.
15 PIXEL
Displays the Pixel Adjust screen to adjust  the clock and phase.
16 AUTO (RGB only)
Press to adjust Position-H/V and Pixel Clock for an optimal picture.
NOTE: The Pixel Phase is not available. 
						

							E – 7
17 POSITION
Press to display the Blanking  screen; press again to display the Posi-
tion screen.
While pressing and holding CTL, pressing this button displays the Lens
Shift adjustment screen.
18 MUTE SOUND
(available only when using with the ISS -6020 or IPS4000)
Turns off the sound for a short period of time. Press again to restore the
sound.
19 MUTE OSD
Press to turn off the on-screen display. Press again to restore the on-
screen display.
NOTE: You can also turn off the on-screen display by pressing and holding CTL
and then pressing MUTE OSD; doing this again restores it. In this case any
adjustment will still change the projectors memory settings. This mode is avail-
able even when an input is switched to another or the power is turned off using
the POWER OFF button on the remote control.
20 MUTE PICTURE
Press to turn off the picture for a shor t period of time. Press again to
restore the picture. Pressing and holding CTL, then pressing this button
shuts off the light completely.
21 KEYSTONE (R)
Press to display the Keystone Correction screen.
22 AMPLITUDE (G)
Service personnel only.
23 ENTRY LIST (B)
Press to display the Entry List screen.
24 FOCUS (+/–)
While pressing and holding CTL, pressing this button allows you to ad-
just the lens focus.
25 MAGNIFY/ZOOM (+/–)
Magnify the size of  a target portion.
While pressing and holding CTL, pressing this button allows you to zoom
the lens in and out.
26 CTL
Used in conjunction with other buttons, similar to a shift key on a com-
puter.
Remote Control Precautions
•Use the remote control within a distance of about 7m (23feet) and at
an angle of 30˚ above, below, to the left and to the right of the remote
control sensor located at the front of the main unit.
•The remote control system may not function when direct sunlight or
strong illumination strikes the remote control sensor of the main unit,
or when there is an obstacle in the path.
•When remote control buttons are pressed and held, main unit func-
tion keys may not operate.
•Do not subject to strong shock.
•Do not allow water or other liquid to splash on the remote control. If
the remote control gets wet, wipe it dry immediately.
•Avoid exposure to heat and steam.
•Remove the batteries from the remote control when the remote con-
trol is not going to be used for a long period.
You cannot operate the projector using the remote control if:
•the remote ID is not set to [00].
•the remote ID is not the same as the projector ID.
See page E-23 for setting remote ID and page E-39 for setting pro-
jector ID.
Remote Control Battery Installation
Installing the Remote Control Batteries
When it comes time to replace the batteries, two AAA type will be
required.
1. Press and open the cover.
OFF
+-
PICTURE ADJUSTAB
CD
EF
G
M
N
WHITE BAL.IMAGE
ON POWER
M
E
N
U
EN
TE
R
1
2
A
D
D
R
E
S
S
P
R
O
JE
C
BS
27 Infrared Transmitter
Direct the remote control toward the remote sensor on the projector
cabinet.
28 Remote Jack
Connect your remote control cable here for wired operation.
28
27
2. Align and insert the batteries according to the (+) and (-) indications
inside the case.
3. Replace the cover. 
						

							E – 8
2. INSTALLATION
Formulas: Screen Width H (5:4) (m) = Screen Height V x 5/4 x 0.0254
Screen Height V (5:4) (m) = Screen Width H x 4/5 x 0.0254
Screen Diagonal (5:4) (m) = Screen Height V x 6.4/4 x 0.0254
Screen Width H (5:4) (inch) = Screen Height V x 5/4
Screen Height V (5:4) (inch) = Screen Width H x 4/5
Screen Diagonal (5:4) (inch) = Screen Height V x 6.4/4
Width (H)
1.6(63)
1.9(75)
2.3(90)
2.9(112.5)
3.4(135)
4.0(157.5)
4.6(180)
5.1(202.5)
5.7(225)
6.7(262.5)
7.6(300)
8.6(337.5)
9.5(375)Height (V)
1.2(50.4)
1.5(60)
1.8(72)
2.3(90)
2.7(108)
3.2(126)
3.7(144)
4.1(162)
4.6(180)
5.3(210)
6.1(240)
6.9(270)
7.6(300)SF Fixed Lens
TL-08SF
0.84:1
1.3(52.9)
1.6(63)
1.9(75.6)
2.4(94.5)
2.9(113.4)
3.4(132.3)
3.8(151.2)
4.3(170.1)
4.8(189)
5.6(220.5)
6.4(252)
7.2(283.5)
8.0(315)TL-1Z/1ZH
1.5-2.5
2.4(94.5) - 4.0(157.5)
2.9(112.5) - 4.8(187.5)
3.4(135) - 5.7(225)
4.3(168.8) - 7.1(281.3)
5.1(202.5) - 8.6(337.5)
6.0(236.3) - 10.0(393.8)
6.9(270) - 11.4(450)
7.7(303.8) - 12.9(506.3)
8.6(337.5) - 14.3(562.5)
10.0(393.8) - 16.7(656.3)
11.4(450) - 19.1(750)
12.9(506.3) - 21.4(843.8)
14.3(562.5) - 23.8(937.5)
NOTE: Distances may vary +/- 5%.
Unit: m (inch)Table of Throw Distances and Image Sizes for Optional Lenses
Zoom Lens
TL-2Z
2.5 - 4.0
4.0(157.5) - 6.4(252)
4.8(187.5) - 7.6(300)
5.7(225) - 9.1(360)
7.1(281.3) - 11.4(450)
8.6(337.5) - 13.7(540)
10.0(393.8) - 16.0(630)
11.4(450) - 18.3(720)
12.9(506.3) - 20.6(810)
14.3(562.5) - 22.9(900)
16.7(656.3) - 26.7(1050)
19.1(750) - 30.5(1200)
21.4(843.8) - 34.3(1350)
23.8(937.5) - 38.1(1500)TL-4Z
4.0-7.0
6.4(252) - 11.2(441)
7.6(300) - 13.3(525)
9.1(360) - 16.0(630)
11.4(450) - 20.0(787.5)
13.7(540) - 24.0(945)
16.0(630) - 28.0(1102.5)
18.3(720) - 32.0(1260)
20.6(810) - 36.0(1417.5)
22.9(900) - 40.0(1575)
26.7(1050) - 46.7(1837.5)
30.5(1200) - 53.3(2100)
34.3(1350) - 60.0(2362.5)
38.1(1500) - 66.7(2625) Screen Size (5:4)
Screen size (Diagonal)
Width (H) Height
(V)
TL-1Z/1ZH (H x 1.5) – (H x 2.5) TL-08SF (H x 0.84)
TL-2Z (H x 2.5) – (H x 4.0)TL-4Z (H x 4.0) – (H x 7.0)
Throw Distance
For screen sizes between 80” and 500” not indicated on the above table, use formulas below.
Projection Distance = Screen Width (H) x Lens Magnification
Throw distance for TL-08SF lens =H x 0.84
Throw distance for TL- 1Z/1ZH lens  =H x 1.5 - H x 2.5
Throw distance for TL- 2Z lens  =H x 2.5 - H x 4.0
Throw distance for TL- 4Z lens  =H x 4.0 - H x 7.0
Screen Size and Projection Distance
Applicable lens and throw distance/ List of screen sizes This section describes how to set up your projector and how to connect
video and audio sources.
Setting Up Your Projector
Your Projector is simple to set up and use. But before you get started,
you must first:
1. Determine the image size
2. Set up a screen or select a non-glossy white wall onto which you can
project your image.
3. Install the optional lens to the projector.
NOTE: The lens must be installed by service personnel only.
4. Connect the supplied power cable.
5. Set up the projector.
6. Connect a PC, VCR, DVD player, or other equipment.
7. Make settings or adjustments on the projector.
NOTE:  Image has 5:4 aspect ratio. Take this into account when specifying a screen. 
						

							E – 9
Lens Shift Adjustable Range
Lens Shift Adjustable Range for Desktop and Ceiling Mount Application
The diagram below shows the location of the image position in the lens. The lens can be shifted within the shaded area as shown using the normal
projection position as a starting point.
Maximum Possible Range for TL-1Z/1ZH, TL-2Z and TL-4Z
Parenthesized values for the ceiling mount application
Up: 0.41 V (0.24 V) Right: 0.28 H (0.19 H)
Down: 0.24 V (0.41 V) Left: 0.19 H (0.28 H)
(H: width of projected image, V: height of projected image)
Desktop/ Front
Vertical
Normal positionMax. 0.41V
1V0.19H
0.28H
0.41V
0.24V (V)
(H) Normal Projection
position
Ceiling/ Front
Vertical
Normal position
Max. 0.41V1V
(H)
(V)
0.41V0.24V Normal Projection
position
0.19H
0.28H Example for Stack
Screen center
Fixed Lens TL-08SF
Maximum Possible Range for TL-08SF
Up: 0.09 V Right: 0.06 H
Down: 0.09 V Left: 0.06 H
(H: width of projected image, V: height of projected image)
NOTE: To reduce the distortion of an image, it is recommended that the projector is horizontally positioned at a projection angle of 0 degree.
0.06H
0.06H
0.09V
0.09V
(H) (V)
Normal Projection
position Normal positionMax. 0.09V1V 
						

							E – 10
Pulling Out the Handles
Pull out the handle until it clicks into place.
Retracting the Handles
1) Push the lever to unlock and  2) retract the handle.
Selecting A Location
The further your projector is from the screen or wall, the larger the im-
age. The minimum size the image can be projected is 80 (2 m) mea-
sured diagonally. The largest the image can be is 500 (12.7 m).
WARNING
•Only use your projector on a solid, level surface. If the projector falls
to the ground, you can be injured and the projector severely dam-
aged.
•Do not use the projector where temperatures vary greatly. The pro-
jector must be used at temperatures between 40 degrees F (5 de-
gree C) and 95 degrees F (35 degree C).
•Do not expose the projector to moisture, dust, or smoke. This will
degrade the screen image.
•Ensure that you have adequate ventilation around your projector for
proper heat dissipation. Do not cover the vents on the projector cabi-
net.
80100200300400500
Moving The Projector
Always carry your projector by the handle. Ensure that the power cord
and any other cables connecting to video sources are disconnected
before moving the projector. When moving the projector or when it is
not in use, cover the lens with the lens cap. 
						

							E – 11
O
F
F
 P
O
W
E
R
 O
N
Connecting the Power Cable and Turn
on the Projector
Before you turn on your projector, ensure that the computer or video
source is turned on and that your lens cap is removed.
1. Connect the supplied power cable to the projector.
Plug the supplied power cable into the AC outlet.
3. BASIC OPERATION
2. Turn On The Projector
The main power switch is on the rear panel of the projector.
By turning this switch on, the projector will go into its standby
mode and the POWER indicator will glow orange. Only after you
press the POWER ON button on the remote control or projector
cabinet will the POWER indicator turn to green and the projector
will fully turn on.
3. Turn Off The Projector
First press the POWER OFF button on the remote control or the
projector cabinet for a minimum of two seconds. Allow the fan to
cool the projector for three minutes.
This will extend the life of the lamp. After the cooling fan stops
working, the POWER indicator will change to a steady orange glow
and the projector will be in the stand-by mode. Then turn off the
main power switch on the rear panel. The POWER indicator will
go out. If you desire to move the projector then unplug the power
cable.
NOTE: Immediately after turning on the projector, screen flicker may occur.This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.
CAUTION: Do not turn off the main power while the cooling fan is working.
OFF POWER ON
OFF
+-
PICTUREADJUSTABC DEFGHIWHITE BAL.IMAGE
ON POWER
MENU
ENTER
123
ADDRESS
PROJECTOR
BS
Using the Power Cable Stopper
The Power cable wire stopper is provided on the projector so that the
cable cannot be accidentally unplugged from the AC IN.
1. Lift up the wire stopper.
2. Plug the power cable into the AC IN.
Power cable
Wire stopper
3. Lift down the wire stopper to hold the power cable.
For North America
For Europe
Power
Switch 
						

							E – 12
CANCEL
About Startup Screen
(Menu Language Select screen)
When you first turn on the projector, you will get the Star tup screen.
This screen gives you the opportunity to select one of the seven menu languages: English, German,
French, Italian, Spanish,Swedish and Japanese.
To select a menu language, follow these steps:
1. Use the Select 
 or  button to select one of the seven languages for the menu.
OFF
+-
PICTUREADJUSTABC DEFGHI
JKL MNO PQR
STU
,.
UNDO CANCEL
TEST
PICTUREKEYSTONE AMPLITUDE ENTRYLISTSOUND OSD
MUTE
MAGNIFYHELP INFO.
POSITION AUTOPIXELVWX YZ/
WHITE BAL.IMAGE
ON POWER
MENU
ENTER
123
456
7
089
ADDRESS
PROJECTOR
RGB
LENS
SHUTTER
BS
+
-
+
-
FOCUSZOOM
CTLLENS
+-
MENU
ENTER
2. Press the Enter button to execute the selection.
+-
MENU
ENTER
3. The Basic/Custom menu will be displayed in the language you
have selected.
To close the menu, press the Cancel button.
After this has been done, you can proceed to the advanced menu operation.
If you want, you can select the menu language later. See Language on page E-37. 
						

							E – 13
Set up the projector
1. Turn on the projector
2. Select your type of projection:
Desktop front, ceiling rear, desktop rear, and ceiling front.
3. Display the test pattern by pressing the TEST button on the re-
mote control or using the menu.
TEST
4. Adjust the image position and the image size.
(1) Press and hold the CTL button and press the POSITION button to display
the Lens Shift adjustment screen.
Use the Select button on the remote control or the LENS SHIFT button on
the projector cabinet to move the image horizontally and vertically.
To close the the Lens Shift adjustment screen, press the CANCEL button.
See page E-9 for “Lens Shift Adjustable Range”.
POSITION
LENS
CTL
+-
(2) Press and hold the CTL and press the ZOOM + or - button to adjust the
image size.  You can also adjust the image size by using the ZOOM + or -
button on the projector cabinet.
MAGNIFY
+
-
+
-
FOCUSZOOM
LENS
CTL
(3) Press and hold the CTL button and press the FOCUS + or - button to
obtain the best focus. You can also adjust the focus by using the FOCUS
+ or - button on the projector cabinet.
MAGNIFY
+
-
+
-
FOCUSZOOM
LENS
CTL