NEC Projector PX803UL-WH User Manual

144
Digital RGB signal connection
•	 Connect	a	commercially	available	HDMI	cable	between	the	computer’s	HDMI	output	terminal	and	the	projector’s	
HDMI	IN	terminal.
•	 Connect	a	commercially	available	DisplayP ort	cable	between	the	computer’s	DisplayP ort	output	terminal	and	the	
projector’s	DisplayPort	IN	terminal.
•	 Select	the	source	name	for	its	appropriate	input	terminal	after	turning	on	the	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
HDMI	IN	HDMIHDMI...

145
Cautions	when	connecting	an	HDMI	cable
•	 Use	a	certified	High	Speed	HDMI®	Cable	or	High	Speed	HDMI®	Cable	with	Ethernet.
Cautions when connecting a DisplayPort cable
•	 Use	a	certified	DisplayPort	cable.
 
•	 Depending	on	the	computer,	some	time	may	be	required	until	the	image	is	displayed.
•	 Some	DisplayPort	cables	(commercially	available)	have	locks.
•	 To	disconnect	the	cable,	press	the	button	on	the	top	of	the	cable’s	terminal,	then	pull	the	cable	out.
•	 Power	can	be	supplied	to	the	connecting...

146
Cautions	when	using	a	DVI	signal
•	 When	the	computer	has	a	DVI	output	terminal,	use	a	commercially	available	conv erter	cable	to	connect	the	com-
puter	to	the	projector’s	HDMI	IN	terminal	(only	digital	video	signals	can	be	input).	
HDMI IN
NOTE:	When	Viewing	a	DVI	Digital	Signal
•	 Turn	off	the	power	of	the	computer	and	projector	before	connecting	devices.
•	 When	a	video	deck	is	connected	via	a	scan	converter,	etc.,	the	display	may	not	be	correct	during	fast-forwarding	and	rewinding.
•	 Use	a...

147
HDMI IN
HDMI OUT
Connecting an External Monitor
You	can	connect	a	separate,	exter nal	monitor	to	your	projector	to	simultaneously	view	on	a	monitor	the	computer	
analog	image	you’re	projecting.
•	 BNC(CV)	component	video	signals	and	BNC(Y/C)	S-video	signals	will	not	be	output.
•	 Please	refer	to	Page	68	when	displaying	the	PIP/PBP	screen.
NOTE:
•	 When	outputting	HDMI	signals,	turn	on	the	power	of	the	video	device	on	the	output	side	and	keep	it	connected	before	inputting	
video	signals	into	this...

148
Connecting Your Blu-ray Player or Other AV Equipment
Component	video	signal/S-video	signal	connection
•	 Select	the	source	name	for	its	appropriate	input	terminal	after	turning	on	the	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
BNC(CV)	BNC(CV)VIDEO
BNC(Y/C)
	BNC(Y/C)S-VIDEO
CV YC
BNC¢CV£
BNC
¢Y£
BNC¢C£
BNC	cable	(not	supplied)
Audio	equipment
6. Installation and Connections  

149
Connecting Component Input
•	 Select	the	source	name	for	its	appropriate	input	terminal	after	turning	on	the	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
COMPUTER	IN	COMPUTERCOMPUTER	1
BNC	BNCCOMPUTER	2
NOTE:
•	 When	the	signal	format	is	set	to	[AUTO]	(default	factory	setting	when	shipped),	the	computer	signal	and	component	signal	are	
automatically	distinguished	and	switched.	If	the	signals	cannot	be	distinguished,	select	[COMPONENT]	under	[ADJUST]	→...

150
Connecting HDMI Input
You	can	connect	the	HDMI	output	of	your	Blu-ray	play er,	hard	disk	play er,	or	notebook	type	PC	to	the	HDMI	IN	terminal	
of	your	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
HDMI	IN	HDMIHDMI
TIP:	For	users	of	audio	video	equipment	with	an	HDMI	terminal:
Select	“Enhanced”	rather	than	“Normal”	if	HDMI	output	is	switchable	between	“Enhanced”	and	“Normal”.
This	will	provide	improved	image	contrast	and	more	detailed	dark	areas.
For	more...

151
Connecting a document camera
You	can	connect	a	document	camera	and	project	printed	documents,	etc.
•	 Select	the	source	name	for	its	appropriate	input	terminal	after	turning	on	the	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
COMPUTER	IN	COMPUTERCOMPUTER	1
BNC(CV)	BNC(CV)VIDEO
BNC(CV)
COMPUTER IN
VIDEO
NOTE:
•	 Name,	position,	and	direction	of	ter-
minals	are	vary	depending	on	camera	
model.	Please	check	user’s	manual	of	
your	camera	for	details.
 
BNC...

152
Connecting to a Wired LAN
The	projector	comes	standard	with	a	Ethernet/HDBaseT	port	(RJ-45)	which	provides	a	LAN	connection	using	a	LAN	
cable.	
To	use	a	LAN	connection,	you	are	required	to	set	the	LAN	on	the	projector	menu.	Select	[SETUP]	→	[NETWORK	
SETTINGS]	→	[WIRED	LAN].	(→	page	127).
Example of LAN connection
Example	of	wired	LAN	connection
Ethernet/HDBaseT
Server
Hub
LAN	cable	(not	supplied)
NOTE:	Use	a	Category	5	or	higher	LAN	cable.
6. Installation and Connections  

153
Connecting to a HDBaseT transmission device (sold commercially)
HDBaseT	is	a	connection	standard	for	home	appliances	that	is	established	by	the	HDBaseT	Alliance.
Use	a	LAN	cable	sold	commercially	to	connect	the	Ethernet	/	HDBaseT	port	of	the	projector	(RJ-45)	to	a	HDBaseT	
transmission	device	sold	commercially.
The	Ethernet/HDBaseT	port	of	the	projector	supports	HDMI	signals	(HDCP)	from	transmission	devices,	control	signals	
from	external	devices	(serial,	LAN)	and	remote	control	signals	(IR...