NEC Projector PX700W2 User Manual

37
❻ Changing Eco Mode/Checking Energy-Saving Effect Using 
Eco Mode [ECO MODE]
This	feature	enables	you	to	select	two	brightness	modes	of	the	lamp:
OFF	and	ON	modes.	The	 lamp 	 life 	 can 	 be 	 extended 	 by 	 turning 	 on 	 the 	 [ECO 	 MODE].
[ECO	MODE]	Description
[OFF]
This	is	the	default	setting	(100%	Brightness).
[ON]Low	lamp	power	consumption	(approx.	 80% 	 Brightness).
To	turn	on	the	[ECO	MODE],	do	the	following:	
1.	 Press	the	ECO/L-SHIFT	button	on	the	remote	control	to	display	[ECO	MODE]...

38
Checking Energy-Saving Effect [CARBON METER]
This	feature	will 	sho w 	energy-sa ving 	eff ect 	in 	ter ms 	of 	CO2	emission	reduction 	(kg) 	when 	the 	projector’ s 	[ECO 	MODE] 	
is	set	to	[OFF],	or	[ON].	This	 feature 	 is 	 called 	 as 	 [CARBON 	 METER].
There	are	tw o 	messages:	[T OTAL 	CARBON 	SA VINGS] 	and 	[CARBON 	SA VINGS-SESSION].	The 	[T OTAL 	CARBON 	
SAVINGS]	message	sho ws 	the 	total 	amount 	of 	CO2	emission	reduction 	from 	the 	time 	of 	shipment 	up 	to 	no w.	Y ou 	can 	
check...

39
❼ Correcting Horizontal and Vertical Keystone Distortion 
[CORNERSTONE]
Use	the	3D 	Ref orm 	f eature 	to 	correct 	k eystone 	(tr apezoidal) 	distor tion 	to 	mak e 	the 	top 	or 	bottom 	and 	the 	left 	or 	r ight 	
side	of	the	screen	longer	or	shorter	so	that	the	projected	image	is	rectangular.
Cornerstone
1.	 Press	and	hold	the	3D	REFORM	button	for	a	minimum	of	2	seconds	to	reset	current	adjustments.
 Current adjustments for [KEYSTONE] or [CORNERSTONE] will be cleared.
2.	 Project	an	image	so	that...

40
7. Use the ▲▼◀▶	button	to	move	the	projected	image	frame	as	shown	on	the	example.
8.	 Press	the	ENTER	button.
9. Use the ▲▼◀▶ button to select another icon which points in the direction.
	 On	the	Cornerstone	adjustment	screen,	select	[EXIT]	or	press	the	EXIT	button	on	the	remote	control.
 The confirmation screen is displayed.
10. Press  the ◀ or ▶	button	to	highlight	the	[OK]	and	press	the	ENTER	button.
This	completes	the	Cornerstone	correction.
Selecting	[CANCEL]	will	return	to	the	adjustment	screen...

41
The	adjustable	ranges	for	3D	Reform	are	as	follows:
HORIZONTALVERTICAL
CORNERSTONEPX750U2:	 Max.	 +/− 	 35° 	 approx.
PX700W2/PX800X2:	Max.	 +/−40° 	 approx.	Max.	+/− 	 30° 	 approx.KEYSTONE
*	 The	following	are	conditions	under	which	the	maximum	angle	is	achieved:
•	 When	the	NP18ZL	(PX750U2)	and	NP08ZL	(PX700W2/PX800X2)	lens	is	used
•	 When	the	lens	shift	is	set	to	the	center
	 When	the	lens 	shift 	is 	used 	and 	y et 	the 	image 	is 	not 	displa yed 	in 	the 	center 	of 	the 	screen, 	the...

42
❽ Displaying Two Pictures at the Same Time
The	projector	has 	a 	f eature 	that 	allo ws 	y ou 	to 	vie w 	tw o 	diff erent 	signals 	sim ultaneously.	Y ou 	ha ve 	tw o 	modes:	PIP 	
mode	and	PICTURE	BY	PICTURE	mode.
•	 From	the	menu	you	can	select	[SETUP]	→	[BASIC]	→	[PIP/PICTURE	BY	PICTURE].	
The	[PIP/PICTURE	BY	PICTURE]	menu	item	has	the	following	three	options:	MODE, 	 POSITION, 	 and 	 SOURCE.
Use	the	▲	or	▼	button	to	select	[MODE],	[POSITION]	or	[SOURCE]	and	press	the	ENTER	button.
Selecting the...

43
Viewing	Two	 Pictures
1.	 Press	the	PIP/FREEZE	button	on	the	remote	control.
	 The	PIP/PBP	SOURCE	screen	will	be	displayed.
2. Use the ▲ or ▼	button	to	select	the	source	and	press	the	ENTER	button.
	 The	PIP	screen 	or 	PICTURE 	BY 	PICTURE 	screen 	will 	be 	displa yed, 	depending 	on 	which 	w as 	selected 	in 	the 	
[MODE] setting screen.
3.	 Press	the	PIP/FREEZE	button	again	to	return	to	the	normal	screen	(single	picture).
TIP:
•	 Selecting	another	source	will	return	to	the	normal	screen.
•...

44
❾ Preventing the Unauthorized Use of the Projector [SECURITY]
A	keyword	can 	be 	set 	f or 	y our 	projector 	using 	the 	Men u 	to 	a void 	oper ation 	b y 	an 	unauthor ized 	user .	When 	a 	k eyword 	
is	set,	turning 	on 	the 	projector 	will 	displa y 	the 	K eyword 	input 	screen.	Unless 	the 	correct 	k eyword 	is 	entered, 	the 	pro-
jector	cannot	project	an	image.	
•	The	 [SECURITY] 	 setting 	 cannot 	 be 	 cancelled 	 by 	 using 	 the 	 [RESET] 	 of 	 the 	 menu.
To	enable	the	Security...

45
7.	 Type	in	the	same	combination	of	▲▼◀▶	buttons	and	press	the	ENTER	button.
 The confirmation screen will be displayed.
8.	 Select	[YES]	and	press	the	ENTER	button.
	 The	SECURITY	function	has	been	enabled.
To turn on the projector when [SECURITY] is enabled:
1.	 Press	the	POWER	button.
 The projector will be tur ned on and display a message to the effect that the projector is locked.
2. Press the MENU button.
3.	 Type	in	the	correct	keyword	and	press	the	ENTER	button.	The 	 projector 	 will...

46
To disable the SECURITY function:
1. Press the MENU button.
 The menu will be displayed.
2.		Select 	 [SETUP] 	→	[INSTALLATION(2)]	→	[SECURITY]	and	press	the	ENTER	button.
 The OFF/ON men u will be displayed.
3.	 Select	[OFF]	and	press	the	ENTER	button.
	 The	SECURITY	KEYWORD	screen	will	be	displayed.
4.	 Type	in	your	keyword	and	press	the	ENTER	button.
	 When	the	correct	keyword	is	entered,	the	SECURITY	function	will	be	disabled.
NOTE:	If	you 	forget 	your 	keyword, 	contact 	your 	dealer . 	Y our...