NEC Projector PH1400U User Manual
Have a look at the manual NEC Projector PH1400U User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
227 9. Appendix ❹ Specifications This section provides technical information about projector’s performance. Optical Model NumberNP-PH1400UProjection SystemDMD™ 0.96" × 3 (aspect 16:10)Resolution*11920 × 1200 pixels (WUXGA)LensOption (see page 229) NP25FL NP26ZL NP27ZL NP28ZL NP29ZL NP32ZL Power Lens Shift(NP26ZL, NP27ZL, NP28ZL, NP29ZL, NP32ZL) −0.4V to +0.55V, +/−0.2H(NP32ZL: +/−0.5V, +/−0.2H) Lamp465W AC (360W in ECO)Light Output*2 *313500 lumensECO: 75%Contrast Ratio*3 (full white: full black)2000:1 with DYNAMIC CONTRAST ON Image Size (Diagonal)100 - 500" (depending on the lens → page 220)80 - 200" on NP25FL, 70 - 600" on NP32ZLProjection Distance (Min.-Max.)(depending on the lens → page 219) *1 Effective pixels are more than 99.99%.*2 This is the light output value (lumens) when the [PRESET] mode is set to [HIGH-BRIGHT]. If any other mode is selected as the [PRESET] mode, the light output value may drop slightly.*3 Compliance with ISO21118-2005 Electrical Model NumberNP-PH1400U Inputs2 × RGB/Component (mini D-Sub 15P), 5 × BNC, 1 × HDMI Type A (HDMI® Connector) HDCP supported*4,1 × DisplayPort (20pin connecter) HDCP supported*4,1 × S-Video (DIN 4P), 1 × Video (BNC)1 × STEREO DVI (DVI-D, Dual Link, 24P), SYNC (BNC)1 × Option SlotOutputs1 × RGB (D-Sub 15P), SYNC (BNC)PC Control1 × PC Control Port (D-Sub 9P)Wired Remote1 × Stereo mini JackWired LAN Port1 × RJ-45 (10BASE-T/100BASE-TX)Wireless LAN Port (Optional)IEEE 802.11 b/g/n (optional Wireless LAN Unit [NP02LM Series] required)USB Port1 × Type AColor Reproduction10-bit signal processing (1.07 billion colors) (VIEWER, NETWORK: Colors, 16.7 million colors)Compatible Signals*5Analog: VGA/SVGA/XGA/XGA+/WXGA/WXGA+/SXGA/SXGA+/UXGA/WUXGA/480i/480p/576i/576p/720p/1080i/1080pHDMI: VGA/SVGA/XGA/WXGA/SXGA/SXGA+/UXGA/WUXGA/480p/576p/720p/1080i/1080p (Refresh rate: 60 Hz only)Horizontal Resolution540 TV lines: NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60300 TV lines: SECAMScan Rate*6Horizontal: 15 kHz to 108 kHz (RGB: 24 kHz or over)Vertical: 48 Hz to 120 Hz (HDMI: 50 Hz to 85 Hz)Sync CompatibilitySeparate Sync / Composite Sync / Sync on GreenPower Requirement200-240V AC, 50/60 HzInput Current6.2 A (200-240V)
228 9. Appendix Model NumberNP-PH1400UPower Con- sumption (Typical value) ECO MODE OFFDual lamp: 1215 WSingle lamp: 705 WECO MODE ONDual lamp: 985 WSingle lamp: 585 WSTANDBY (NORMAL)90WNETWORK STANDBY60WSTANDBY (POWER-SAVING) 0.5W *4 HDMI ® (Deep Color, Lip Sync)/DisplayPort with HDCP What is HDCP/HDCP technology? HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content Protection (HDCP) is a system for preventing illegal copying of video data sent over a High-Definition Multimedia Interface (HDMI). If you are unable to view material via the HDMI and DisplayPort input, this does not necessarily mean the projector is not function-ing properly. With the implementation of HDCP, there may be cases in which certain content is protected with HDCP and might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC). Video: Deep Color; 8/10/12-bit, LipSync Audio: LPCM; up to 2 ch, sample rate 32/44.1/48 KHz, sample bit; 16/20/24-bit*5 An image with higher or lower resolution than the projector’s native resolution (1920 × 1200) will be displayed with scaling tech- nology. *6 Some scan rates are not supported depending on the resolution of its input signal. Mechanical Model NumberNP-PH1400U Installation OrientationDesktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear Dimensions22.0" (W) × 22.8" (H) × 9.3" (D) /558 mm (W) × 578 mm (H) × 235 mm (D)(not including protrusions)Weight87.1 lbs/39.5 kg (without lens)Environmental ConsiderationsOperational Temperatures: 32° to 104°F (0° to 40°C) *7,20% to 80% humidity (non-condensing) at sea levelStorage Temperatures: 14° to 122°F (−10° to 60°C),20% to 80% humidity (non-condensing)Operating altitude: 0 to 2600 m/8500 feet (1600 to 2600 m/5500 to 8500 feet: Set [FAN MODE] to [HIGH ALUTITUDE])RegulationsUL/C-UL Approved (UL 60950-1, CSA 60950-1)Meets DOC Canada Class A requirementsMeets FCC Class A requirementsMeets AS/NZS CISPR.22 Class AMeets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)Meets Low Voltage Directive (EN60950-1, TUV GS Approved) *7 95 to 104°F (35 to 40ºC) - “Forced eco mode” For additional information visit: US : http://www.necdisplay.com/ Europe : http://www.nec-display-solutions.com/ Global : http://www.nec-display.com/global/index.htm l For information on our optional accessories, visit our website or see our brochure. The specifications are subject to change without notice.
229 9. Appendix Option lens NP25FLManual focusthrow ratio 0.67:1, F2.5, f=14.6 mmImage Size (Diagonal): 80 – 200 inches / 2.03 – 5.08 mProjection Distance(Min.-Max.): 1.1 – 3.2 mNP26ZLPower zoom and focusthrow ratio 1.39-1.87:1, F2.5, f=28.9-38.9 mmImage Size (Diagonal): 100 – 500 inches / 2.54 – 12.7 mProjection Distance(Min.-Max.): 2.8 – 24 mNP27ZLPower zoom and focusthrow ratio 1.87-2.56:1, F2.5, f=39-53.4 mmImage Size (Diagonal): 100 – 500 inches / 2.54 – 12.7 mProjection Distance(Min.-Max.): 4.0 – 24.0 mNP28ZLPower zoom and focusthrow ratio 2.56-4.16:1, F2.5, f=52.4-85.3 mmImage Size (Diagonal): 100 – 500 inches / 2.54 – 12.7 mProjection Distance(Min.-Max.): 9.0 – 45.0 mNP29ZLPower zoom and focusthrow ratio 4.16-6.96:1, F2.5, f=84.9-142.0 mmImage Size (Diagonal): 100 – 500 inches / 2.54 – 12.7 mProjection Distance(Min.-Max.): 12.0 – 80.0 mNP32ZLPower zoom and focusthrow ratio 0.9-1.1:1, F2.5-2.7, f=19.4-23.3 mmImage Size (Diagonal): 70 – 600 inches / 1.78 – 15.2 mProjection Distance(Min.-Max.): 1.4 – 14.4 m • These specifications and the product’s design are subject to change without notice. Power Cord If the supplied power cord cannot be used or in your area the voltage condition is different from the supplied power cord, use power cords that are suitable for the electrical specifications, types of power cords and regulations of the country of installation, as shown in the following table as shown below. For more information, contact your dealer. Power Cord Electrical Specifications Power supplyPower cord electrical specsAC 200 - 240V250V 16A or higher Type of power cord plug connector cord Plug and cord Your plug must comply with your country’s safety requirements and your outlet type. Connector Dimensions of the connector of the power cord are shown below 7+0.5 −0 13±0.2 20 min 2.5 +0.5 −08±0.2 2.5 +0.5 −0R3.5 min 6.0 +0.5 −0 28+0 −0.920+0 −0.7 Unit: mm
230 9. Appendix 578 (22.8)653 (25.7) 39.5 (1.6) 499 (19.6)430 (16.9) 235 (9.3) 283.7 (11.2) 628 (24.7)480 (18.9) 558 (22)700 (27.6) 119.9 (4.7) 155.3 (6.1) 333 (13.1) 48.7 (1.9) ❺ Cabinet Dimensions Lens center Lens center Unit: mm (inch)
231 9. Appendix ❻ Pin Assignments of D-Sub COMPUTER Input Connector Mini D-Sub 15 Pin Connector Signal Level Video signal : 0.7Vp-p (Analog) Sync signal : TTL level 5 14 23 10 11 12 13 14 15 69 78 Pin No. RGB Signal (Analog) YCbCr Signal 1 Red Cr 2 Green or Sync on GreenY 3 Blue Cb 4 Ground 5 Ground 6 Red GroundCr Ground7Green GroundY Ground8Blue GroundCb Ground9No Connection10Sync Signal Ground11No Connection12Bi-directional DATA (SDA)13Horizontal Sync or Composite Sync 14Vertical Sync15Data Clock
232 9. Appendix ❼ Troubleshooting This section helps you resolve problems you may encounter while setting up or using the projector. Indicator Messages POWER Indicator Indicator display Projector status ProcedureOff Power is off.– FlashingBlue (short flashes)Preparing to turn power onWait a while.Blue (long flashes)Off timer (enabled)Program timer (off time enabled)– Orange (short flashes)Projector coolingWait a while.Orange (long flashes)Program timer (on time enabled)Lit BluePower on– OrangeStandby mode (NORMAL or NETWORK STANDBY) –Red Standby mode (POWER-SAVING)– STATUS Indicator Indicator display Projector status Procedure OffNo problem, or standby mode (POWER-SAVING or NETWORK STANDBY)– FlashingRed (cycles of 1)Cover problemThe lamp cover is not properly mounted. Mount it properly. (→ Page 191)Red (cycles of 4)Fan problemThe cooling fan has stopped turning. Contact an NEC projector cus-tomer support center for repairs.FlashingOrangeNetwork conflictIt is not possible to connect the projector’s built-in LAN and wireless LAN simultaneously to the same network. To connect the projector’s built-in LAN and wireless LAN simultaneously, connect them to differ-ent networks.LitGreen Standby mode (NOR- MAL) – Orange Button has been pressed while projector is in key lock mode The projector’s keys are locked. The setting must be canceled to oper-ate the projector. (→ Page 131) Projector’s ID number and remote control’s ID number do not match Check the control IDs. (→ Pages 131 and 132) LAMP 1/LAMP 2 Indicator Indicator display Projector status Procedure OffThe lamp is turned off.– Flashing GreenPreparing to relight lamp after lighting has failedWait a while. RedLamp replacement grace periodThe lamp has reached the end of its service life and is now in the replacement grace period (100 hours). Replace the lamp as soon as possible. (→ page 189)Red (cycles of 6)Lamp does not lightThe lamp has not turned on. Wait at least 1 minute, then turn the power back on. If the lamp still does not light, contact an NEC projector customer support center.LitRedLamp usage time exceededThe lamp has exceeded its usage time. The projector’s power cannot be turned on until the lamp is replaced. (→ page 189) GreenLamp lit–
233 9. Appendix Temp. Indicator Indicator display Projector status Procedure OffNo problemFlashing RedTemperature problemThe temperature protector has been activated. If the room temperature is high, move the projector to a cool place. If the TEMP. indicator still be flashing when the projector is used at operating temperatures, contact an NEC projector customer support center.OrangeWarming upThe usage environment temperature is lower than the projector’s operating temperature (0°C). In that case, raise the usage environment temperature to a 0°C or higher and turn on the projector. If the projector is turned on at around 0°C, it may take 5 minutes to warm up the projector. During this warm-up period the TEMP. indicator will flash. When the warm-up is completed, the TEMP. indicator will go off. SHUTTER Indicator Indicator display Projector status Procedure Off Light – Flashing Green Lens calibration is in process.– On GreenLight shuttered– If the temperature protector is activated If the projector’s internal temperature rises abnormally, the lamp turns off and the temperature indicator flashes (repeatedly in cycles of 2). It may happen that the projector’s temperature protector is simultaneously activated and the projector’s power turns off. If this happens, do the following: - Unplug the power cord from the power outlet. - If using in a place where the surrounding temperature is high, move the projector to a different, cool place. - If there is dust in the ventilation holes, clean. (→ pages 184 and 188) - Wait as such about 1 hour for the projector’s internal temperature to lower.
234 9. Appendix Common Problems & Solutions (→ “Power/Status/Lamp Indicator” on page 232.) ProblemCheck These Items Does not turn on or shut down• Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control is on� (→ pages 15, 18, 19)• Ensure that the lamp cover is installed correctly. (→ page 191)• Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the room where you are presenting is particularly warm, move the projector to a c\ ooler location�• Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end of its life� If so, replace the lamp� After replacing the lamp, reset the lamp hours used� (→ page 142)• The lamp may fail to light. Wait a full minute and then turn on the power again.• Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600 meters or higher� Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH ALTITUDE] can cause the projector to overheat and the projector could shut down� If this happens, wait a couple minutes and turn on the projector � (→ page 133) If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an image for some time and then the projector will display the image� Wait for a moment� Will turn off• Ensure that the [OFF TIMER], [AUTO POWER OFF] or [PROGRAM TIMER] is off. (→ page 125, 136, 163) No picture • Check if the appropriate input is selected. (→ page 22) If there is still no picture, press the SOURCE button or one of the input buttons again�• Ensure your cables are connected properly.• Use menus to adjust the brightness and contrast. (→ page 115)• Ensure that the lens cover is open. (→ page 18)• Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. (→ page 142)• Enter your registered keyword if the Security function is enabled. (→ page 46)• If the HDMI input or the DisplayPort signal cannot be displayed, try the following.- Reinstall your driver for the graphics card built in your computer, or use the updated driver � For reinstalling or updating your driver, refer to the user guide accompanied with your computer or graphics card, or contact the support center for your computer manufacturer � Install the updated driver or OS on your own responsibility � We are not liable for any trouble and failure caused by this installation\ �• Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the power to the notebook PC� In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up�* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or power management software�• See also the page 236� Picture suddenly becomes dark• Check if the projector is in the Forced ECO mode because of too high ambient temperature. If this is the case, lower the internal temperature of the projector by selecting [HIGH] for \ [FAN MODE]� (→ page 133) Color tone or hue is unusual • Check if an appropriate color is selected in [WALL COLOR]. If so, select an appropriate option. (→ page 123)• Adjust [HUE] in [PICTURE]. (→ page 115) Image isn’t square to the screen • Reposition the projector to improve its angle to the screen. (→ page 24)• Use the Keystone correction function to correct the trapezoid distortion. (→ page 31) Picture is blurred • Adjust the focus. (→ page 29)• Reposition the projector to improve its angle to the screen. (→ page 24)• Ensure that the distance between the projector and screen is within the adjustment range of the lens. (→ page 219) • Has the lens been shifted by an amount exceeding the guaranteed range? (→ page 222)• Is the lens inserted until it comes to a complete stop? (→ page 167)• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on. Should this happen, let the projector stand until there is no condensati\ on on the lens� Flicker appears on screen• Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500 feet/1600 meters or lower � Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTITUDE] can cause the lamp to overcool, causing the image to flicker � Switch [FAN MODE] to [AUTO]� (→ page 133)
235 9. Appendix Image is scrolling vertically, horizontally or both• Check the computer’s resolution and frequency. Make sure that the resolution you are trying to display is supported by the projector � (→ page 225)• Adjust the computer image manually with the Horizontal/Vertical in the [IMAGE OPTIONS]. (→ page 117) Remote control does not work • Install new batteries.(→ page 10)• Make sure there are no obstacles between you and the projector.• Stand within 22 feet (7 m) of the projector. (→ page 10)• If the remote control cable plug is inserted into the REMOTE jack, the remote control does not function wirelessly. (→ page 11)• Make sure that the remote control’s ID corresponds with the projector’s ID. (→ page 131, 132) Indicator is lit or blinking • See the POWER/STATUS/LAMP Indicator. (→ page 232) Cross color in RGB mode • Press the AUTO ADJ. button on the projector cabinet or the remote control. (→ page 33)• Adjust the computer image manually with [CLOCK]/[PHASE] in [IMAGE OPTIONS] in the menu. (→ page 116) No on-screen display • Check if the on-screen mute is turned on. To turn off the on-screen mute, press the ON-SCREEN button on the remote control or hold down the MENU button on the projector cabinet for\ at least 10 seconds� (→ page 37) For more information contact your dealer.
236 9. Appendix If there is no picture, or the picture is not displayed correctly. • Power on process for the projector and the PC. Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the power to the notebook PC. In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up. NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information. If it reads “0kHz”, this means there is no signal being output from the computer. (→ page 139 or go to next step) • Enabling the computer’s external display. Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector. When using a PC compatible laptop, a combination of function keys will enable/disable the external display. Usu- ally, the combination of the “Fn” key along with one of the 12 function keys gets the external display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through external display selections. • Non-standard signal output from the computer If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use. Each notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the previous step. Refer to your computer’s documentation for detailed information. • Image displayed is incorrect when using a Macintosh When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projector) according to your resolution. After setting, restart your Macintosh for the changes to take affect. For setting display modes other than those supported by your Macintosh and the projector, changing the DIP switch on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP switch to the 13" fixed mode and then restart your Macintosh. After that, restore the DIP switches to a displayable mode and then restart the Macintosh again. NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a MacBook which does not have a mini D-Sub 15-pin connector. • Mirroring on a MacBook * When using the projector with a Macintosh MacBook, output may not be set to 1024 × 768 unless “mirroring” is off on your MacBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring. • Folders or icons are hidden on the Macintosh screen Folders or icons may not be seen on the screen. Should this happen, select [View] → [Arrange] from the Apple menu and arrange icons.