NEC Projector Ph1000u User Manual

							57
3. Convenient Features
•	NAME
PROJECTOR	NAMEEnter	a	name	 for	your	 projector	 so	that	 your	 computer	 can	identify	 the	projector. 	A	
projector	name	must	be	16	characters	or	less. 	
TIP:	Projector	name	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
HOST	NAMEEnter	 the	hostname	 of	the	 network	 connected	 to	the	 projector. 	A	 host	 name	 must	be	
15	or	less.
DOMAIN	NAMEEnter	 the	domain	 name	of	the	 network	 connected	 to	the	 projector. 	A	 domain	 name	
must	be	60	characters	or	less.
•	ALERT	MAIL
ALERT	MAILThis	option	 will	notify	 your	computer	 of	lamp	 replace	 time	or	error	 messages	 via	e-mail	
when	using	wireless	or	wired	LAN. 	
Placing	a	checkmark	will	turn	on	the	Alert	Mail	feature.
Clearing	a	checkmark	will	turn	off	the	Alert	Mail	feature.
Sample	of	a	message	to	be	sent	from	the	projector:
The	lamp	and	filters	are	at	the	end	of	its	usable	life. 	Please	replace	the	lamp.
Projector	Name:	XXXXX
Lamp	1	Hours	Used: 	XXX	[H]
Lamp	2	Hours	Used:	XXX	[H]
SENDER’S	ADDRESSEnter	sender’s	address. 	
SMTP	SERVER	NAMEEnter	the	SMTP	server	name	to	be	connected	to	the	projector.
RECIPIENT’S	ADDRESS	
1,	2,	3
Enter	your	recipient’s	address. 	Up	to	three	addresses	can	be	entered.
TEST	MAILSend	a	test	mail	to	check	whether	your	settings	are	correct	or	not
NOTE:
•	 If	you	execute	 a	test,	you	may	not	receive	 an	Alert	mail.	Should	this	 happen,	check	if	 network	
settings are correct.
•	 If	you	entered	 an	incorrect	 address	in	a	test,	 you	may	 not	receive	 an	Alert	 mail.	 Should	 this	
happen,	check	if	the	Recipient’s	Address	is	correct.
SAVEClick	this	button	to	save	your	settings	to	the	projector’s	memory. 
						

							58
3. Convenient Features
•	NETWORK	SERVICE
PJLink	PASSWORDSet	a	password	 for	PJLink*. 	A	 password	 must	be	32	characters	 or	less. 	Do	 not	 forget	
your	password. 	However,	if	you	forget	your	password,	consult	with	your	dealer.
HTTP	PASSWORDSet	a	password	for	HTTP	server. 	A	password	must	be	10	characters	or	less.
AMX	BEACONTurn	on 	or 	off 	for 	detection 	from 	AMX 	Device 	Discovery 	when 	connecting 	to 	the 	network	
supported	by	AMX’s	NetLinx	control	system.
TIP:	
When	 using	a	device	 that	supports	 AMX	Device	 Discovery,	 all	AMX	 NetLinx	 control	system	 will	rec-
ognize	the	device	and	download	the	appropriate	Device	Discovery	Module	from	an	AMX	server.
Placing	a	checkmark	will	enable	detecting	the	projector	from	AMX	Device	Discovery.
Clearing	a	checkmark	will	disable	detecting	the	projector	from	AMX	Device 	Discovery.
NOTE: If you forget your password, contact your dealer. 
*What	is	PJLink?
PJLink	is	a	standardization	 of	protocol	 used	for	controlling	 projectors	of	different	 manufacturers. 	This	 standard	 proto-
col	is	established	by	Japan	Business	Machine	and	Information	System	Industries	Association	(JBMIA)	in	2005.
The	projector	supports	all	the	commands	of	PJLink	Class	1.
Setting	of	PJLink	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
•	INFORMATION
WIRED	LANDisplay	a	list	of	settings	of	wired	LAN	connection.
WIRELESS	LANDisplay	a	list	of	settings	of	wireless	LAN	connection.
UPDATEReflect	settings	when	they	are	changed. 
						

							59
3. Convenient Features
 Projecting Your Computer’s Screen Image from the 
Projector via a Network [NETWORK PROJECTOR]
By	selecting	 the	projector	 connected	 to	the	 same	 network	 as	that	 of	your	 PC,	the	PC	screen	 image	can	be	projected	
to	the	screen	via	network. 	There	is	no	need	of	connection	using	the	computer	cable	(VGA).
Operation Environment
Applicable	OSWindows	7	Professional
Windows	7	Ultimate
Windows	7	Enterprise	
Windows	 Vista	Home	Premium
Windows	Vista	Business
Windows	Vista	Ultimate
Windows	Vista	Enterprise
Hardware	specificationsThe	specifications	 recommended	 by	Microsoft	 as	the	 operation	 environment	 for	
Windows	7/Windows	 Vista	should	be	satisfied.
Network	EnvironmentWired	LAN	or	wireless	LAN	environment	that	supports	 TCP/IP	is	required.
Screen	colorHigh	Color	(16	bits)
True	Color	(24	bits	and	32	bits)
*	Setting	with	256	colors	or	less	is	not	available.
Setting	the	Projector	to	Network	Projector	Input	Mode
1.	 With	the	projector	turned	on,	press	the	SOURCE	button.
 The input selection window appears.
	 Another	 way	to	display	 the	input	 selection	 window	is	to	 press	 the	NETWORK	 button	on	the	 remote	 control.	The	
APPLICATION	MENU	screen	will	be	displayed. 	Go	to	step	3. 
						

							60
3. Convenient Features
2.	 Press	the	 or 	button	to	select	[NETWORK]	and	press	the	ENTER	button.
	 In	the	screen,	the	[APPLICATION	MENU]	menu	is	displayed.
3.	 From	the	[APPLICATION	MENU]	menu,	select	[NETWORK	PROJECTOR].
	 The	[PROJECTOR	NAME/DISPLAY	RESOLUTION/PASSWORD/URL]	will	be	displayed. 
						

							61
3. Convenient Features
Projecting	the	Image	with	Network	Projector
1.	 Click	[Start]	from	the	desktop	of	Windows	7.
2.	 Click	[All	Programs].
3.	 Click	[Accessories].
4.	 Click	[Connect	to	a	Network	Projector].
	 When	the	[Permission	Connect	to	a	Network	Projector]	window	appears,	click	[Yes.].
	 The	“Connect	to	a	Network	Projector” 	window	appears.
5.	 Click	[→	Search	for	a	projector	(recommended)].
	 In	the	“Available	projectors” 	box,	“PH1000	Series” 	is	displayed.
6.	 Click	[PH1000	Series].
	 The	message	 “Enter	the	password	for	the	projector	that	you	selected.” 	is	displayed	at	the	bottom	of	the	window. 
						

							62
3. Convenient Features
7.	 Input	the	password	to	the	password	input	box	displayed	by	the	operation	at	step	3	on	page	60.
8.	 Click	[Connect].
	 The	network	projector	function	works	and	the	screen	of	Windows	7	is	projected	from	the	projector.
•	 If	the	resolution	 of	your	 computer’s	 screen	is	different	 from	the	projector’s	 screen	resolution,	 the	NETWORK	
PROJECTOR	 function	may	not	work. 	If	 this	 happens,	 change	the	resolution	 of	the	 computer’s	 screen	to	lower	
resolution	than	the	one	displayed	at	Step	3	on	page	60.
NOTE:	 When	the	network	 projector	 function	works,	the	background	 color	of	the	 desktop	 changes	 to	black.	 When	the	network	
projector function is stopped, the original background color is restored\
.
Reference:	 If	the	 projector	 cannot	be	found	 at	Step	 5,	click	 [	→	Enter	 the	projector	 address].	 Then,	input	the	“Network	 address”	
(Input	example:	 http://10.32.97.61/lan)	 and	“Projectorpassword”	 (Input	example:	 82291627)	 displayed	in	the	 screen	 projected	
from the projector.
Exiting	the	Network	Projector	Operation
1.	 Click	[Projecting: 	PH1000	Series]	in	the	 Windows	Vista	task	bar.
2.	 Click	[Disconnect].
	 The	Network	Projector	function	is	stopped.
3.	 Press	the	SOURCE	button	of	the	projector	to	select	an	input	terminal	other	than	[NETWORK].
	 When	using	the	remote	control,	press	a	button	other	than	the	NETWORK	button. 
						

							63
3. Convenient Features
 Using the Projector to Operate Your Computer via a Network 
[REMOTE DESKTOP]
•	 By	 selecting	 the	PC	connected	 to	the	 same	 network	 as	that	 of	the	 projector,	 the	PC	screen	 image	can	be	projected	
to	the	screen	via	network.
	 Then,	 by	operating	 the	keyboard,	 you	can	 operate	 Windows	 7,	Windows	 Vista	or	Windows	 XP	on	the	 PC	connected	
with	the	network.
•	 With	the	Remote	Desktop	function,	you	can	remotely	operate	the	PC	placed	at	a	distance	from	the	projector.
Meeting	room
Office
NOTE:
•	 The	[REMOTE	DESKTOP]	function	will	work	on	the	following	Windows	editions.
	 Windows	7	Professional
	 Windows	7	Ultimate
	 Windows	7	Enterprise	
	 Windows	Vista	Business
	 Windows	Vista	Ultimate
	 Windows	Vista	Enterprise
	 Windows	XP	Professional	with	Service	Pack	3
	 (Note)
•	 In	 this	user’s	 manual	 this	feature	 is	described	 using	Windows	 7	as	 an	 example,	 but	Windows	 Vista	and	Windows	 XP	Professional	
Service	Pack	2	or	later	will	also	work	with	this	feature.
•	 A	keyboard	is	required	to	use	the	Remote	Desktop	function.
•	 The	 Remote	 Desktop	 function	 can	be	operated	 with	a	keyboard.	 Using	a	wireless	 mouse	with	a	wireless	 keyboard	 is	more	 useful	
for operating.
Use	a	commercially	available	wireless	keyboard,	a	wireless	mouse,	and	a	USB	wireless	receiver.
Use	a	commercially	available	USB	keyboard	and	USB	mouse.
•	 A	USB	keyboard	with	a	built-in	USB	hub	cannot	be	used	with	the	projector.
•	 A	wireless	keyboard	or	mouse	that	supports	Bluetooth	cannot	be	used	with	the	projector.
•	 We	do	not	warrant	that	the	USB	port	of	the	projector	will	support	all	USB	devices	in	the	market. 
						

							64
3. Convenient Features
Prepare	a	commercially	available	wireless	keyboard	(US	layout	version).
Connect	the	USB	 wireless	 receiver	to	the	 USB	 port	(Type	 A)	of	the	 projector. 	Make	 all	necessary	 settings	for	your	
wireless	keyboard	and	mouse. 
						

							65
3. Convenient Features
Setting the password to the user account of Windows 7
TIP:	If	a	password	has	been	set	for	an	account,	the	steps	1	to	9	can	be	skipped.
1.	 Click	[Start]	from	the	desktop	of	Windows	7.
2.	 Click	[Control	Panel].
3.	 Click	[Add	or	remove	user	accounts]	displayed	under	[User	Accounts].
4.	 When	the	[User	Account	Control]	confirmation	window	appears, 	click	[Continue].
5.	 Click	[Administrator].
6.	 Click	[Create	a	password].
7.	 Input	the	password	to	the	[New	password]	box.
8.	 Input	the	same	password	as	that	at	Step	7	to	the	[Confirm	new	password]	box.
9.	 Click	[Create	a	password].
 The Administrator is changed to [Password Protection].
Setting the Remote Access
1.	 Click	[Start]	from	the	desktop	of	 Windows	7.
2.	 Click	[Control	Panel].
3.	 Click	[System	and	Security].
4.	 Click	[Allow	remote	access]	displayed	under	[System].
5.	 When	the	[User	Account	Control]	confirmation	window	appears, 	click	[Continue].
	 The	[System	Properties]	window	appears.
6.	 Click	[Allow	connections	 from	computers	 running	any	version	 of	Remote	 Desktop	 (less	secure)]	 in	the	
Remote	Desktop	box	and	click	[OK].
Checking	the	IP	address	on	 Windows	7
1.	 Click	[Start]	from	the	desktop	of	 Windows	7.
2.	 Click	[Control	Panel].
3.	 Click	[View	network	status	and	tasks]	displayed	under	[Network	and	Internet]. 
						

							66
3. Convenient Features
4.	 Click	[View	status]	displayed	in	blue	on	the	right	of	[Local	Area	Connection]	in	the	window.
	 The	[Local	Area	Connection	Status]	window	appears.
5.	 Click	[Details...].
	 Write	down	the	value	for	“IPv4	IP	Address”	(xxx.xxx.xxx.xxx)	displayed.
6.	 Click	[Close].
7.	 Click	[X]	at	the	upper	right	of	the	window.
	 The	system	goes	back	to	the	desktop.
Starting	the	Remote	Desktop
1.	 With	the	projector	turned	on, 	press	the	SOURCE	button.
 The input selection window appears.
	 Another	 way	to	display	 the	input	 selection	 window	is	to	 press	 the	NETWORK	 button	on	the	 remote	 control.	The	
APPLICATION	MENU	screen	will	be	displayed. 	Go	to	step	3.