NEC Projector P502WL User Manual

Projector
P502HL/P502WL
User’s Manual
Model No.
NP-P502HL, NP-P502WL 

Ver. 1 6/15
•	 Apple,	Mac,	Mac	OS,	MacBook,	and	iMac	are	trademarks	of	Apple	Inc.	registered	in	the	U.S.	and	other	countr ies.
•	 App	Store	is	a	service	mark	of	Apple	Inc.
•	 IOS	is	a	trademark	or	registered	trademark	of	Cisco	in	the	U.S.	and	other	countries	and	is	used	under	license .
•	 Microsoft,	Windows,	Windows	Vista,	Internet	Explorer,	.NET	Fr amework	and	Po werPoint	are	either	a	registered	
trademark	or	trademark	of	Microsoft	Corporation	in	the	United	States	and/or	other	countries.
•	 MicroSaver...

i
Important Information
Safety Cautions
Precautions
Please	read	this	manual	carefully	before	using	your	NEC	projector	and	keep	the	manual	handy	for	future	reference.
CAUTION
To	turn	off	main	power,	be	sure	to	remove	the	plug	from	power	outlet.
The	power	outlet	socket	should	be	installed	as	near	to	the	equipment	as	possible ,	and	should	be	easily	
accessible.
CAUTION
TO	PREVENT	SHOCK,	DO	NOT	OPEN	THE	CABINET.
THERE	ARE	HIGH-VOLTAGE	COMPONENTS	INSIDE.
REFER	SERVICING	TO	QUALIFIED	SER VICE	PERSONNEL.
This...

ii
WARNING TO CALIFORNIA RESIDENTS:
Handling	the	cables	supplied	with	this	product	will	expose	you	to	lead,	a	chemical	known	to	the	State	of	California	
to	cause	birth	defects	or	other	reproductive	harm.	WASH	HANDS	AFTER	HANDLING.
RF Interference (for USA only)
WARNING
The	Federal	Communications	Commission	does	not	allow	any	modifications	or	changes	to	the	unit	EXCEPT	those	
specified	by	NEC	Display	Solutions	of	America,	Inc.	in	this	manual.	Failure	to	comply	with	this	government	regu-
lation	could	void...

iii
WARNING
•	 Do	not	cover	the	lens	with	the	lens	cap	or	equivalent	while	the	projector	is	on.	Doing	so	can	lead	to	melting	of	
the	cap	due	to	the	heat	emitted	from	the	light	output.
•	 Do	not	place	any	objects,	which	are	easily	affected	by	heat,	in	front	of	the	projector	lens.	Doing	so	could	lead	
to	the	object	melting	from	the	heat	that	is	emitted	from	the	light	output.	
•	 Do	not	use	a	spra y	containing	flammable	gas	to	get	rid	of	accumulated	dust	and	dirt	on	the	cabinet	and	the	lens.	It	
may	cause...

iv
•	 Handle	the	power	cord	carefully.	A	damaged	or	frayed	po wer	cord	can	cause	electr ic	shoc k	or	fire .
-	 Do	not	use	any	power	cord	other	than	the	one	supplied	with	the	projector.
-	 Do	not	bend	or	tug	the	power	cord	excessively.
-	 Do	not	place	the	power	cord	under	the	projector,	or	any	heavy	object.
-	 Do	not	cover	the	power	cord	with	other	soft	materials	such	as	rugs.
-	 Do	not	heat	the	power	cord.
-	 Do	not	handle	the	power	plug	with	wet	hands.
•	 Turn	off	the	projector,	unplug	the	power	cord...

v
Light Module
1.	 A	light	module	containing	multiple	laser	diodes	is	equipped	in	the	product	as	the	light	source.
2.	 These	laser	diodes	are	sealed	in	the	light	module.	No	maintenance	or	service	is	required	for	the	performance	of	
the	light	module.
3.	 End	user	is	not	allowed	to	replace	the	light	module.
4.	 Contact	qualified	distributor	for	light	module	replacement	and	further	information.
Laser Safety Caution
•	 The	laser	module	is	equipped	in	this	product.
	 Use	of	controls	or	adjustments	of...

vi
•	 The	labels	are	stuck	on	the	below	indicated	position.
 
Label 1Label 2
	 Label	1:	
 
	 Label	2:	
 
Important Information  

vii
About Copyright of original projected pictures:
Please	note	that	using	this	projector	for	the	purpose	of	commercial	gain	or	the	attraction	of	public	attention	in	a	venue	
such	as	a	coffee	shop	or	hotel	and	employing	compression	or	expansion	of	the	screen	image	with	the	following	func-
tions	may	raise	concern	about	the	infringement	of	copyrights	which	are	protected	by	copyright	law.
[ASPECT	RATIO],	[KEYSTONE],	Magnifying	feature	and	other	similar	features.
Turkish RoHS information relevant for Turkish...

viii
Power management function
The	projector	has	power	management	functions.	To	reduce	pow er	consumption,	the	pow er	management	functions	(1	
and	2)	are	factory	preset	as	shown	below .	To	control	the	projector	from	an	exter nal	device	via	a	LAN	or	serial	cable	
connection,	use	the	on-screen	menu	to	change	the	settings	for	1	and	2.
1. STANDBY MODE (Factory preset: NORMAL)
 To control the projector from an external device, select [NETWORK STANDBY] for [STANDBY MODE].
NOTE:
•	 When	[NORMAL]	is	selected	for...