NEC Projector Np4001 User Manual

1. Introduction 
9 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
Green 
8.  LAMP 2 
Flashing See Indicator Messages 113 
Green 
Orange 9.  POWER (LED) 
Flashing See Indicator Messages 112 
10.  STATUS (LED)  Green 
Lamp ready you can safely turn 
on or off the projector 112 
11.  ON/STAND BY Turn the projector on or off  
(main power switch must be turned on first) 10, 37 
12.  ENTER  Select or change settings in the OSD 61 
13.  
LEFT 
CURSOR/VOLUME 
DECREASE Decrease volume 
46 
 
 
 
 
 
 
 
 
 
 
  

1. Introduction 
10
r Terminal Panel Features 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  COMPUTER 3 IN  Connect the DVI cable (not supplied) from a 
computer 31 
2.  AUDIO IN (3) Connect the audio cable (not supplied) from 
the input device — 
3.  AUDIO OUT  Audio loop-thru —
 
4.  MONITOR OUT  Connect to a monitor — 
5.  REMOTE 2  Connect the remote to the projector 16 
6.  AUDIO IN (2)  Connect the audio cable (not supplied) from 
the input device —
 
7.  L/MONO, R 
(COMPONENT)  Connect an RCA audio...

1. Introduction 
11 
ITEM LABEL DESCRIPTION SEE PAGE: 
10.  SC TRIGGER  When connected to the screen through a 
commercially available cable, the screen de-
ploys automatically on start up of the 
projector. The screen retracts when the pro-
jector is powered off (see notes below) 130 
11.  S-VIDEO 
Connect a commercially available S-video 
cable from a video device 35 
12.  POWER SWITCH  Turn on/off the projector 37, 47 
13.  AC IN  Connect the supplied power cable 36 
14.  L/MONO, R Connect RCA audio...

1. Introduction 
12
s Part Names of the Remote Control 
The Remote Control unit supplied with the projector combines ergonomic design and utility 
and includes features such as Volume and Z oom Control, Freeze Frame and a useful point-
ing tool in the form of a laser. Refer to t he following diagram and table for button location and 
functionality. 
ITEM LABEL LABEL ITEM 
1.    Remote jack  Exit button 18.
  
2.    Laser pointer  Laser button 19.
  
3.    Infrared transmitter  L-Click button 20.
  
4....

1. Introduction 
13 
 
Important: 
1. Avoid using the projector with bright fl uorescent lighting turned on. Certain high-
frequency fluorescent lights can disrupt remote control operation. 
2. Be sure nothing obstructs the path betw een the remote control and the projec-
tor. If the path between remote and projector is obstructed, you can bounce the 
remote signal off certain reflective  surfaces such as projector screens. 
3. The buttons and keys on the projector hav e the same functions as the...

1. Introduction 
14
Battery Installation 
The Remote Control unit included with the projector does not contain batteries, though 
batteries are supplied as part of the complete package. To insert (or replace) the batter-
ies, refer to the following guide. 
1.  Remove the battery compartment 
cover by squeezing the locking 
catch (A) and sliding the cover in 
the direction of the arrow (B). 
 
2.  Insert the supplied batteries tak-
ing note of the polarity (+/-) as 
shown. 
 
3.  Replace the cover...

1. Introduction 
15 
Operating Range for Wi reless Remote Control 
The infrared signal operates by  line-of-sight up to a distance of about 22 feet (7m) and 
within a 60-degree angle of the remote sensor on the projector cabinet.  
The projector will not respond if there are  objects between the remote control and the 
sensor, or if strong light falls  on the sensor. Weak batteries  will also prevent the remote 
control from properly operating the projector. 
Remote Control Precautions 
The following...

1. Introduction 
16
Using the Remote Control in Wired Operation 
Connect the supplied remote cable to the REMOTE2 jack on the projector (see r Ter-
minal Panel Features on page 
10 ) and the other end to the remote jack on the remote 
control (see item 1, 
s  Part Names of the Remote Control on page 12 ). 
Note:   
Connecting the remote cabl e to the REMOTE2 jack on the terminal panel will 
make the wireless operation unavailable. 
 
 
 
 
  

 
17 
2. Installation and Connections 
n Setting Up the Screen and the Projector 
This section briefly describes how to set up your projector and how to connect video and  
audio sources.  
Your projector is simple to set up and use.  But before you get started, you must first:  
•   Set up a screen and the projector.  
•   Connect your computer or video equipment to the projector.  
See 
s Making Connections on pages 31, 32, 33, 34,  and 35. 
•   Connect the supplied power cable.  
See 
t Connecting...

2. Installation and Connections 
18
o Selecting a Location 
Locating the projector correc tly ensures optimum performa nce and a longer parts life. 
Take note of the following when setting up the projector: 
•  The projector table or stand should be level and sturdy. 
•   Position the projector so that it is perpendicular to the screen. 
•   Ensure cables do not cause a trip hazard.