NEC Projector Np3151w User Manual

9
6. Using On-Screen Menu
[MENU]
Selecting menu Color [COLOR SELECT]
You can choose between two options for menu color: color and monochrome.
Turning  On  /  Off  Source  Display,  message  and Time  [SOURCE  DISpLAY],  [mESSAGE  DISpLAY], 
[TImE DISpLAY]
SOURCE.DISPLA y.........
This.option. turns.on.or.off. input. name. display. such.as.Computer. 1,.Computer. 2,.Computer. 3,.Compo-
nent,.Video,.and.No.Input.to.be.displayed.on.the.top.right.of.the.screen.
MESSAGE.DISPLA y.............

98
6. Using On-Screen Menu
[INSTALLATION]
Selecting projector Orientation [ORIENTATION]
This  reorients  your  image  for  your  type  of  projection. The  options  are:  desktop  front  projection,  ceiling  rear  projec-
tion, desktop rear projection, and ceiling front projection.
DESKTOP FRONT
CEILING REAR
DESKTOP REAR CEILING FRONT 

99
6. Using On-Screen Menu
no-signal area
Selecting Aspect Ratio and position for Screen [SCREEN]
SCREEN.TyPE........Select. one.of.two. options:. 4:3.SCREEN. or.WIDE. SCREEN. for.the. screen. to.be. used.. See.also. [ASPECT.
RATIO
].
(→ .page.84)
POSITION
............... This.feature. allows.you.to.adjust. the.vertical. position. of.the. image. when.WIDE. SCREEN. has.been. selected.
for.the.screen.type.
When.WIDE.SCREEN.has.been.selected.there.is.no-signal.area.above.and.below.the.image.
NOTE: This...

00
Setting Security [SECURITY SETTINGS]
Disabling the Cabinet Buttons [CONTROL pANEL LOCK]
This option turns on or off the Control Panel Lock function.
NOTE:
• This Control Panel Lock does not affect the remote control functions.
•  When  the  control  panel  is  locked,  pressing  and  holding  the  EXIT  button  on  the  projector  cabinet  for  about  10  seconds  will 
change the setting to [ OFF].
Setting a password [BACKGROUND LOCK]
A password can be set for your projector to avoid operation...

0
6. Using On-Screen Menu
2. Type the same password again and press the ENTER button.
  Your password will be assigned.
[DELETE] 
To delete your password:
1. Select [DELETE PASSWORD] and press the ENTER button.
2.  Enter your password.
  An asterisk will be displayed.
3.  Press the ENTER button.
  Your password will be deleted.
NOTE: 
•  Do not forget your password. However, if you forget your keyword, consult with your dealer.
•  The [BACKGROUND LOCK] will not be affected even when [RESET] is...

0
6. Using On-Screen Menu
[SECURITY]
The Security function enables you to protect your projector so that the projector will not project a signal unless you 
enter a keyword. There is also an option to lock the projector by using a registered USB memory* as a protect key. 
Once you have registered your USB memory as a protect key, you are required to insert the registered USB mem-
ory  into  the  USB  port  of  the  projector  each  time  you  turn  on  the  projector. You  can  enable  the...

03
6. Using On-Screen Menu
To register a USB memory device as a protect key.
preparation: Insert the USB memory device into the USB port (type A) of the projector.
1.  Use the SELECT 
 or  button to select [ USE PROTECT KEY] and press the ENTER button.
2.  Use the SELECT 
 or  button to select [ READ] and press the ENTER button.
  Data of the USB memory will be read into the projector.
3.  Use the SELECT 
 or  button to select [ REGISTER] and press the ENTER button.
  Downloaded data will be...

04
6. Using On-Screen Menu
•  the  security  disable  mode  is  maintained  until  the  main  power  is  turned  off  (by  setting  the  main  power  switch to “O” or unplugging the power cord).  in the following cases you will be asked to check the protect key or input 
the password:
(1)  When [OK] is selected at an image for which security is set and the power is turned off then back on
(2)  When the main power is turned off then back on while the security function is enabled
(3)  When you...

05
6. Using On-Screen Menu
NOTE: What is PJLink?
PJLink is a standardization of protocol used for controlling projectors of different manufacturers. This standard protocol is estab-
lished by Japan Business Machine and Information System Industries Assoc\
iation (JBMIA) in 2005.
The projector supports all the commands of PJLink Class 1.
Setting of PJLink will not be affected even when [Reset] is done from th\
e menu.
[NETWORK SETTINGS]
This feature allows you to set various setting items when the...

0
6. Using On-Screen Menu
To receive error messages or information on the remaining lamp life via e-mail:1.  On the [ MAIL
] tab, select [ ALERT MAIL] and press the ENTER button. A check mark will be placed. 
2.  Set  [ SENDER’S  ADDRESS
],  [SMTP  SERVER  NAME]  and  [ RECIPIENT’S  ADDRESS].  Select  [OK]  and 
press the ENTER button.
  (
→ page 113)
To execute [Easy Connection] using Image Express Utility 2.0:
The [Easy Connection] is a mode that can abbreviate the troublesome LAN settings...