NEC Projector Np216 User Manual

							2
1. Introduction
 Introduction to the Projector
This section introduces you to your new projector and describes the features and controls.
Congratulations on Your Purchase of the Projector
This  DLP®  projector  is  one  of  the  very  best  projectors  available  today. The  projector  enables  you  to  project  precise 
images up to 300 inches (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR, 
DVD player or document camera.
You can use the projector on a tabletop or cart, you can use the projector to project images from behind the screen, 
and the projector can be permanently mounted on a ceiling*1. The remote control can be used wirelessly.
*1  Do not attempt to mount the projector on a ceiling yourself.
 The  projector  must  be  installed  by  qualified  technicians  in  order  to  ensure  proper  operation  and  reduce  the  risk  of  bodily 
injury.
 In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance with any 
local building codes. Please consult your dealer for more information.
Features you'll enjoy:
•	 Quick	start	&	Quick	Power	Off
  7 seconds after turning on the power, the projector is ready to display PC or video images.
 The projector can be put away immediately after the projector is powered down. No cool down period is required 
after the projector is turned off from the remote control or cabinet control panel.
•	 Direct	Power	Off
 The projector has a feature called “Direct Power Off ”. This feature allows the projector to be turned off (even when 
projecting an image) by disconnecting the AC power supply.
 To turn off the AC power supply when the projector is powered on, use a power strip equipped with a switch and 
a breaker.
•	 Less	than	1W	in	standby	condition	with	energy	saving	technology
	 Selecting	 [POWER-SAVING]	 for	[STANDBY	 MODE]	from	the	menu	 can	put	the	projector	 in	power-saving	 mode	
that consumes only 0.49W (100-130V AC)/0.71W (200-240V AC).
•	 Carbon	Meter
 This  feature  will  show  energy-saving  effect  in  terms  of  CO2	emission	 reduction	 (kg)	when	 the	projector’s	 [ECO	
MODE]	is	set	to	[ON].
 The amount of CO2 emission reduction will be displayed in the confirmation message at the time of power-off and 
in the INFO of the on-screen menu.
•	 7W	built-in	speaker	for	an	integrated	audio	solution
  Powerful 7 watt speaker provides volume need for large rooms.
•	 Two	computer	inputs	provided	(NP216	only)
 The  NP216  projector  comes  with  two  computer  input  ports  (Mini  D-Sub15P)  with  audio  inputs  (two  stereo  mini 
jacks) as well as composite and S-video inputs with audio inputs (a pair of L/R RC\
A jacks). 
•	 DLP
®		projector	with	high	resolution	and	high	brightness	
  High  resolution  display  -  up  to  UXGA  compatible,  XGA  (NP216/NP215/NP210)/  SVGA  (NP115/NP110)  native 
resolution.
•	 AUTO	POWER	ON	and	AUTO	POWER	OFF	features
 The AUTO POWER ON(AC), AUTO POWER ON(COMP.), AUTO POWER OFF, and OFF TIMER features eliminate 
the need to always use the POWER button on the remote control or projector cabinet. 
						

							3
1. Introduction
•	 Preventing	unauthorized	use	of	the	projector
 Enhanced smart security settings for keyword protection, cabinet control panel lock, security slot, chain opening 
to	help	prevent	unauthorized	access,	adjustments	and	theft	deterrence.
•	 The	supplied	remote	control	allows	you	to	assign	a	CONTROL	ID	to	the	projector
 Multiple projectors can be operated separately and independently with the same single remote control by assigning 
an ID number to each projector.
•	 Integrated	RJ-45	connector	for	wired	networking	capacity	(NP216/NP215	only)
	 An	RJ-45	connector	is	equipped	as	standard	feature.
•	 3D	images	supported
 The projector provides 3D images to a user wearing commercially available DLP® Link compatible LCD shutter 
eyeglasses.
About this user's manual
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to 
review the user's manual. This may save you time later on. At the beginning of each section of the manual you'll find 
an overview. If the section doesn't apply, you can skip it.
In this user's manual the drawings of the projector show an example of NP215. 
						

							4
1. Introduction
 Part Names of the Projector
Zoom Lever
(→ page 23)
Controls
(→ page 5)
Lens Lens CapBuilt-in Security Slot ( 
 )*
Adjustable Tilt Foot Lever
(→ page 22)
Adjustable Tilt Foot(→ page 22)
Remote Sensor
(→ page 8)
Front/Top
AC Input
Connect the supplied power 
cable's three-pin plug here, and 
plug the other end into an active 
wall outlet. (→ page 17)Terminal Panel
(→ page 6)
Rear
* This security slot supports the MicroSaver ® Security System.
Ventilation (outlet)Heated air is ex-
hausted from here.
Ventilation (inlet)
Lamp Cover
(→ page 71)
Focus Ring
(→ page 23)
Ventilation (inlet)
Monaural Speaker (7W) Rear Foot
(→ page 22)
Security chain opening Attach an anti-theft device.
The security chain opening accepts 
security wires or chains up to 0.18 
inch/4.6 mm in diameter.
Spacer (black rubber)To fine-adjust the height of the rear 
foot, remove the spacer and rotate 
the rear foot to the desired height. 
						

							5
1. Introduction
Top Features
1.	 POWER	Button	(ON	/	STAND	 BY)	()	(→
 page  18, 
27)
2.  POWER Indicator (→
 page 17, 18, 27, 73)
3. STATUS Indicator (→
 page 73)
4.	 LAMP	Indicator	(→
 page 70, 73)
5.	 AUTO	ADJ. 	Button	(→
 page 26)
6.	 SOURCE	Button	(→
 page 20)
7.	 MENU	Button	(→
 page 43)
8. △▽◁▷	/	Keystone	△▽	/	Volume	◁▷	Buttons
 (→
 page 24, 26, 29)
9.	 ENTER	Button
10.	EXIT	Button
78 9 10 56 12 3 4 
						

							6
1. Introduction
Terminal Panel Features
1.	 COMPUTER	OUT	Connector	 (Mini	D-Sub	 15	Pin)	
(→
 page 13)
2.	 C O M P U T E R	 I N /	C o m p o n e n t	 I n p u t	C o n n e c t o r	
(Mini	D-Sub	15	Pin)	(→
 page 12, 13, 14)
3.	 VIDEO	IN	Connector	(RCA)	(→
 page 15)
4.	 S-VIDEO	IN	Connector	(Mini	DIN	4	Pin)
 (→
 page 15)
1.	 COMPUTER	 1	IN/	 Component	 Input	Connector	
(Mini	D-Sub	15	Pin)	(→
 page 12, 13, 14)
 AUDIO	 IN	Mini	 Jack	 (Stereo	 Mini)	(→
 page  12, 13, 
14)
2.	 COMPUTER	 2	IN/	 Component	 Input	Connector	
(Mini	D-Sub	15	Pin)	(→
 page 12, 13, 14)
 AUDIO	 IN	Mini	 Jack	 (Stereo	 Mini)	(→
 page  12, 13, 
14)
3.	 MONITOR	 OUT	(COMP	 1)	Connector	 (Mini	D-Sub	
15	Pin)	(→
 page 13)
 AUDIO	OUT	Mini	Jack	(Stereo	Mini)	(→
 page 13)
5.	 AUDIO	IN	Mini	Jack	(Stereo	Mini)
 (→
 page 12, 13, 14, 15)
6.	 PC	CONTROL	Port	(D-Sub	9	Pin)	(→
 page 81)
 Use  this  por t  to  connect  a  PC  or  control  system. 
This enables you to control the projector using serial 
communication  protocol.  If  you  are  writing  your  own 
program, typical PC control codes are on page 81.
7.	 LAN	Port	(RJ-45)	(NP215 only) ( →
 page 16)
4.	 PC	CONTROL	Port	(D-Sub	9	Pin)	(→
 page 81)
 Use  this  por t  to  connect  a  PC  or  control  system. 
This enables you to control the projector using serial 
communication  protocol.  If  you  are  writing  your  own 
program, typical PC control codes are on page 81.
5.	 S-VIDEO	IN	Connector	(Mini	DIN	4	Pin)
 (→
 page 15)
6.	 VIDEO	IN	Connector	(RCA)	(→
 page 15)
7.	 VIDEO/S-VIDEO	AUDIO	Input	Jacks	L/R	(RCA)
 (→
 page 12, 13, 14, 15)
8.	 LAN	Port	(RJ-45)	(→
 page 16)
12 2
1
3
34
45
5 6
6 7
NP215
NP216
NP210/NP115/NP110
2467 8
1
5
3 
						

							7
1. Introduction
´
3
7
5
6
1
2
10
12
13
11
14
9
4
8
26
27
28
16
17
22
24
25 21
15
20
19 18
23
29
 Part Names of the Remote Control
1.
 Infrared Transmitter
 (→ page 8)
2.	 POWER	ON	Button
 (→ page 18)
3.	 POWER	OFF	Button
 (→ page 27)
4, 	5, 	6.	COMPUTER	1/2/3	Button
 (→ page 20) 
  (COMPUTER  2/3  button  is  not  available  on  NP215/
NP210/NP115/NP110.  COMPUTER  3  button  is  not 
available on NP216.)
7.	 AUTO	ADJ. 	Button
 (→ page 26)
8.	 VIDEO	Button
 (→ page 20)
9.	 S-VIDEO	Button
 (→ page 20)
10.	VIEWER	Button
 (not available on this series of projectors)
11.	ID	SET	Button
 (→ page 60)
12.	Numeric	Keypad	Button/CLEAR	Button
 (→ page 60)
13.	FREEZE	Button
 (→ page 29)
14.	AV-MUTE	Button
 (→ page 29)
15.	MENU	Button
 (→ page 43)
16.	EXIT	Button	(→ page 43)
17.	 
	Button	(→ page 43)
18.	ENTER	Button	(→ page 43)
19.	MAGNIFY	(+)(–)	Button
 (→ page 29)
20.	MOUSE	L-CLICK	Button*
 (→ page 35, 36)
21.	MOUSE	R-CLICK	Button*
 (→ page 35, 36)
22. PAGE /	Button*
 (→ page 35, 36)
23.	ECO	MODE	Button	(→ page 30)
24.	KEYSTONE	Button
 (→ page 25)
25.	PICTURE	Button
 (→ page 48, 49)
26.	VOL. 	(+)(–)	Button
 (→ page 26)
27.	ASPECT	Button
 (→ page 52)
28.	FOCUS/ZOOM	Button
 (not available on this series of projectors)
29.	HELP	Button
 (→ page 66)
* The PAGE /, MOUSE L-CLICK and MOUSE R-CLICK buttons work only when the optional remote mouse re -
ceiver (NP01MR) is connected with your computer. 
						

							8
1. Introduction
30° 30°30°
30°
OPEN
Remote Control Precautions
•	 Handle	the	remote	control	carefully.
•	 If	the	remote	control	gets	wet,	wipe	it	dry	immediately.
•	 Avoid	excessive	heat	and	humidity.
•	 Do	not	heat,	take	apart,	or	throw	batteries	into	fire.
•	 If	you	will	not	be	using	the	remote	control	for	a	long	time,	remove	the	batteries.
•	 Ensure	that	you	have	the	batteries’ 	polarity	(+/−)	aligned	correctly.
•	 Do	not	use	new	and	old	batteries	together,	or	use	different	types	of	batteries	together.
•		 Dispose	of	used	batteries	according	to	your	local	regulations.
Operating Range for Wireless Remote Control
1Press firmly and slide the battery 
cover off.2Install new batteries (AAA). Ensure 
that you have the batteries’ polarity 
(+/−)	aligned	correctly.
•	 The	infrared	 signal	operates	 by	line-of-sight	 up	to	a	distance	 of	about	 22	feet/7	 m	and	 within	 a	60-degree	 angle	of	
the remote sensor on the projector cabinet.
•	 The	 projector	 will	not	 respond	 if	there	 are	objects	 between	 the	remote	 control	and	the	sensor,	 or	if	strong	 light	falls	
on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.
Battery Installation
7 m/22 feet
7 m/22 feet
Remote control
Remote sensor on projector cabinet
OPEN
3Slip  the  cover  back  over  the  bat -
teries  until  it  snaps  into  place.  Do 
not mix different types of batteries 
or new and old batteries.
Remote control 
						

							9
32
1
2. Installation and Connections
This section describes how to set up your projector and how to connect video and audio sources.
Your projector is simple to set up and use. But before you get started, you must first:
 Setting Up the Screen and the Projector
Selecting a Location
The	further	 your	projector	 is	from	 the	screen	 or	wall,	 the	larger	 the	image. 	The	 minimum	 size	the	image	 can	be	is	30"	
(0.76 m) measured diagonally when the projector is roughly 49 inches (1.3 m) from the wall or screen. The largest 
the	 image	 can	be	is	300"	 (7.6	m)	when	 the	projector	 is	about	 493	inches	 (12.5	m)	from	 the	wall	 or	screen. 	Use	 the	
chart below as a rough guide.
	Set up a screen and the projector.
	 Connect your computer or video equip -
ment to the projector. See pages  12, 13, 
14, 15, 16.
	 Connect the supplied power cable. See 
page 17.
NOTE: Ensure that the power cable and any other 
cables are disconnected before moving the projec -
tor. When moving the projector or when it is not 
in use, cover the lens with the lens cap.
NOTE:
•	 The	distances	are	indicated	by	intermediate	values	between	tele	and	wide.	Use	as	a	rule	of	thumb.
•	 The	Zoom	lever	adjusts	the	image	size	up	to	+/-5%
•	 For	more	details	on	throw	distance,	see	next	page.
To the wall outlet.
300
240
200
180
150
120
100
60
40 8030
1.7m/65.5"2.5m/98.5"3.3m/131.5"4.2m/164"5.0m/197"6.3/246"7.5m/295.5"8.3m/328"10.0m/394"12.5m/492.5"
Distance (Unit: m/inch)
Lens center
Screen	Size	(diagonal:
	inch)
Screen	Size	(Unit:	cm/inch)
609.6(W) x 457.2(H) / 240(W) x 180(H)
487.7(W) x 365.8(H) / 192(W) x 144(H)
406.4(W) x 304.8(H) / 160(W) x 120(H)
365.8(W) x 274.3(H) / 144(W) x 108(H)
304.8(W) x 228.6(H) / 120(W) x 90(H)
243.8(W) x 182.9(H) / 96(W) x 72(H)
203.2(W) x 152.4(H) / 80(W) x 60(H)
162.6(W) x 121.9(H) / 64(W) x 48(H)
121.9(W) x 91.4(H) / 48(W) x 36(H)
81.3(W) x 61.0(H) / 32(W) x 24(H)
1.3m/49"
61.0(W) x 45.7(H) / 24(W) x 18(H) 
						

							10
2. Installation and Connections
Throw Distance and Screen Size
The  following  shows  the  proper  relative  positions  of  the  projector  and  screen.  Refer  to  the  table  to  determine  the 
position of installation.
Distance Chart
CD
B
Screen center
Lens center
Screen bottom
2.7"/68 mm
Installation surface
Screen SizeB C
D(WIDE) a
Diagonal WidthHeight Wide-Tele Wide-Tele
inch mminch mminch mminch mminch mm-inch mminch mmdegree -degree
30 762 24610 18457 12297  46 1180  -52 1320  3 69  14.0 - 12.7 
40 1016 32813 24610 16396  62 1573  -69 1760  4 91  14.0 - 12.7 
60 1524 481219 36914 23594  93 2360  -104  2640  5 137  14.0 - 12.7 
70 1778 561422 421067 27693  108 2753  -121  3080  6 160  14.0 - 12.7 
80 2032 641626 481219 31792  124 3147  -139  3520  7 183  14.0 - 12.7 
90 2286 721829 541372 35891  139 3540  -156  3960 
8 206  14.0 - 12.7 
100 2540 802032 601524 39990  155 3933  -173  4400  9 228  14.0 - 12.7 
120 3048 962438 721829 471188  186 4720  -208  5280  11 274  14.0 - 12.7 
150 3810 1203048 902286 581486  232 5900  -260  6600  13 343  14.0 - 12.7 
180 4572 1443658 1082743 701783  279 7080  -312  7920  16 411  14.0 - 12.7 
200 5080 1604064 1203048 781981  310 7867  -346  8800  18 457  14.0 - 12.7 
240 6096 1924877 1443658 942377  372 9440  -416 10560  22 548  14.0 - 12.7 
270 6858 2165486 1624115 1052674  418 10620  -468 11880  24 617  14.0 - 12.7 
300 7620 240
60961804572 1172971  465 11800  -520 13200  27 685  14.0 - 12.7 
B = Vertical distance between lens center and screen center
C = Throw distance
D = Vertical distance between lens center and bottom of screen(top of screen for ceiling application)
α = Throw angle
NOTE: The values in the tables are design values and may vary. 
						

							11
2. Installation and Connections
 WARNING
* Installing your projector on the ceiling must be done 
by a qualified technician. Contact your NEC dealer 
for more information.
* Do not attempt to install the projector yourself.
•	 Only	 use	your	 projector	 on	a	solid,	 level	surface. 	If	
the projector falls to the ground, you can be injured 
and the projector severely damaged.
•	 Do	 not	use	 the	projector	 where	temperatures	 vary	
greatly. The projector must be used at temperatures 
between	41˚F 	(5˚C) 	and 	104˚F 	(40˚C). 	([ECO 	MODE]	
is	 set	 automatically	 to	[ON]	 at	95°F	 to	104°F/35°C	
to	 40°C. 	Note	 that	[ECO]	 mode	will	be	set	 to	[ON]	
automatically	 at	86°F	 to	104°F/30°C	 to	40°C	 when	
used	in	[HIGH	ALTITUDE].)
•	 Do 	not 	expose 	the 	projector 	to 	moisture, 	dust, 	or	
smoke. This will harm the screen image.
•	 Ensure	 that	you	have	 adequate	 ventilation	 around	
your  projector  so  heat  can  dissipate.  Do  not  cover 
the vents on the side or the front of the projector.
Reflecting	the	Image
Using a mirror to reflect your projector's image enables 
you to enjoy a much larger image when a smaller space 
is required. Contact your NEC dealer if you need a mirror 
system. If you're using a mirror system and your image 
is inverted, use the MENU and   buttons on your 
projector  cabinet  or  your  remote  control  to  correct  the 
orientation. (→ page 59)