NEC Projector M323W User Manual

20
2. Projecting an Image (Basic Operation)
Zoom
[M403X/M363X/M323X/M283X/M403W/M363W/M323W/M403H/M323H]
Use	the	ZOOM	lever	to	adjust	the	image	size	on	the	screen.
[M333XS/M353WS/M303WS]
The	image	size	can	be	adjusted	electronically	from	the	menu.	To	do	so,	follow	the	steps	below.
Adjusting	with	the	ZOOM	button	on	the	remote	control
1.  Press the ZOOM button. 
	 The	DIGITAL	ZOOM	bar	will	be	displayed.
2.  Press the ◀ or ▶	button	to	adjust	the	image	size. 	
3.	 Press	the	EXIT	button.
	 The	DIGITAL	ZOOM...

21
2. Projecting an Image (Basic Operation)
Focus
Use	the	FOCUS	ring	to	obtain	the	best	focus.
Focus Ring
Focus Lever
[M403X/M363X//M323X/M283X/M403W/M363W/
M323W/M403H/M323H][M333XS/M353WS/M303WS]
Use	the	FOCUS	lever	to	obtain	the	best	focus. 

22
2. Projecting an Image (Basic Operation)
❻ Correcting Keystone Distortion Manually
If	the	 screen 	is	 tilted 	vertically, 	keystone 	distortion	 becomes	large. 	Automatic	 Keystone	Correction 	function 	is	 turned 	on 	
at	the	 time	 of	shipment. 	To	 correct	 keystone	 distortion	 manually,	 proceed	with	the	following	 steps	to	correct	 keystone	
distortion. 
 
NOTE:	
•	 The	Keystone	correction	can	cause	an	image	to	be	slightly	blurred	because	the	correction	is	made	electronically.
•	 The	Keystone...

23
2. Projecting an Image (Basic Operation)
Adjusting with the remote control
1.	 Press	the	KEYSTONE	button.
 The Keystone bar will be displayed.
 
2. Use the  ◀ or ▶	button	to	correct	the	keystone	distortion.
  Adjust so that the right and left sides are parallel.
 
3.	 Press	the	EXIT	button.
 The Keystone bar will be closed. 

24
2. Projecting an Image (Basic Operation)
[M403W/M363W/M323W/M403X/M363X/M323X/M283X/M403H/M323H]
1. Press the ▼ (  ) button on the projector cabinet 
with	no	menus	displayed. 	
 The Keystone screen will be displayed on the screen.
•	 Press 	the 	KEYSTONE 	button 	when 	using 	the 	remote	
control.
2.  Press the ▼	button	 to	select	 [VERTICAL]	 and	then	
use the  ◀ or ▶	so	 that	 the	left	and	 right	 sides	 of	the	
projected	image	are	parallel.
*	 Adjust	the	vertical	keystone	distortion.
Projected...

25
2. Projecting an Image (Basic Operation)
6.	 After	completing 	Keystone 	correction, 	press 	the	
EXIT	button. 	
 The Keystone screen will disappear.
•	 To	 perform	 Keystone	 correction	 again,	press	the	▼ 
button  to  display  the  Keystone  screen  and  repeat 
above steps 1 to 6. 

26
2. Projecting an Image (Basic Operation)
❼ Optimizing Computer Signal Automatically
Adjusting the Image Using Auto Adjust
Optimizing	a	computer	image	automatically.	(COMPUTER)
Press	the	AUTO	ADJ.	button	to	optimize	a	computer	image	automatically.
This	adjustment	may	be	necessary	when	you	connect	your	computer	for	the	first	time.
[Poor picture]
[Normal picture]
NOTE:
Some	signals	may	take	time	to	display	or	may	not	be	displayed	correctly.
•	 If	the 	Auto 	Adjust 	operation 	cannot 	optimize 	the...

27
2. Projecting an Image (Basic Operation)
❾ Turning off the Projector
To	turn	off	the	projector:
1. First,  press  the   (POWER)  button  on  the  projector 
cabinet  or  the  STANDBY  button  on  the  remote  con -
trol. 
  The confirmation message will be displayed.
2.	 Secondly, 	press 	the 	ENTER 	button 	or 	press 	the 	 
(POWER)	or	the	STANDBY	button	again.
 The cooling fans stop operating when the projector turns off 
and goes into standby mode. When in standby mode, the 
POWER  indicator  will...

28
2. Projecting an Image (Basic Operation)
❿ After Use
Preparation:	Make	sure	that	the	projector	is	turned	off.
1.	 Unplug	the	power	cord.
2. Disconnect any other cables.
•	 Remove	the	USB	memory	if	it	is	inserted	into	the	projector.
3.	 Retract	adjustable	tilt	foot	if	extended.
(M403W/M363W/M323W/M403X/M363X/M323X/M283X/M403H/M323H	only)
4. 	Slide	the	lens	cover	to	the	left	to	cover	the	lens.
5.	 Put	the	projector	and	accessories	in	the	supplied	soft	case.
  Place the projector in the soft case with...

29
❶ Turning off the Image and Sound
Press	the	AV-MUTE	 button	to	turn	 off	the	 image	 and	sound	 for	a	short	
period	of	time. 	Press	again	to	restore	the	image	and	sound.
The	projector’s	 power-saving	 function	will	work	 10	seconds	 after	the	im-
age	is	turned	off.
As	a	result,	the	lamp	power	will	be	reduced.
NOTE:
•	
Even	though	the	image	is	turned	off,	the	menu	still	remains	on	the	screen.
•	 Sound	from	the	AUDIO	OUT	jack	(Stereo	mini)	can	be	turned	off.
•	 Even	 when	the	power-saving	 function...