NEC Plasmasync 60xc10 Users Manual

							PlasmaSync 42XC10
PlasmaSync 50XC10
PlasmaSync 60XC10
English
User’s Manual
 
						

							Package Contents
Plasma Monitor
Remote control and AA Batteries
Power cord
Users Manual (CD-ROM) 
Start Up Guide (Paper / CD-ROM)
Main Power Switch cover and screw
Cable clamps •
•
•
•
•
•
•
 
						

							Important Safety Instructions ..............................................................................................................English-1
Important Information ...........................................................................................................................English-2
Safety Precautions and Maintenance ...................................................................................................English-3
Recommended Use ....................................................................................................................................English-4
Installation
 Optional Stands/Mounts ..........................................................................................................English-6
 Mounting Location ....................................................................................................................English-6
  Mounting on Ceiling ..................................................................................................................English-7
  Maintenance, Orientation, Cable Management ..................................................................English-7
  Using the Remote ......................................................................................................................English-8
Part Names and Functions
 Control Panel ..............................................................................................................................English-9
 Terminal Panel ............................................................................................................................English-10
 Remote Control ..........................................................................................................................English-11
  Power, Display, Digital Zoom, Pointer, Main Power Switch Cover .....................................English-12
  Remote Control ID .....................................................................................................................English-13
On-Screen Display (OSD)
  Using the OSD .............................................................................................................................English-14
 OSD ................................................................................................................................................English-15
Operation 
  Picture Size Using Video Signals ............................................................................................English-18
  Picture Size Using Computer Signals ....................................................................................English-19
  Split Screen Mode .....................................................................................................................English-20 
 Picture-in-Picture Mode .........................................................................................................English-21 
RS-232C  .......................................................................................................................................................English-23
Troubleshooting.........................................................................................................................................English-27
Specifi cations
 42XC10..........................................................................................................................................English-28
 50XC10 .........................................................................................................................................English-29
 60XC10 .........................................................................................................................................English-30
Supported Resolutions
 42XC10..........................................................................................................................................English-31
 50XC10 .........................................................................................................................................English-33
 60XC10 .........................................................................................................................................English-35
Pin Assignment ..........................................................................................................................................English-37
Table of  Contents
 
						

							English
English-1
Read Before Operating Equipment.
1.   Read these instructions.
2.  Keep these instructions.
3.   Heed all warnings.
4.   Follow all instructions.
5.   Do not use this apparatus near water.
6.   Clean only with a dry cloth.
7.   Do not block any of the ventilation openings. Install in 
accordance with the manufacturer's instructions.
8.   Do not install near any heat sources such as radiators, 
heat registers, stoves, or other apparatus (including 
amplifi ers) that produce heat.
9.   Do not defeat the safety purpose of the polarized or 
grounding-type plug. A polarized plug has two blades 
with one wider than the other. A grounding type plug 
has two blades and third grounding prong Th e wide 
blade or third prong are provided for your safety. If the 
provided plug does not fi t into your outlet, consult an 
electrician for replacement of the obsolete outlet.
10.  Protect the power cord from being walked on or 
pinched particularly at plugs, convenience receptacles, 
and the point where they exit from the apparatus.
11.  Only use attachments/accessories specifi ed by the 
manufacturer
12. Use only with the cart, stand, tripod, bracket, or 
table specifi ed by the manufacturer, or sold with the 
apparatus. When a cart is used, use caution when 
moving the cart or apparatus combination to avoid 
injury from tip-over.
13.  Unplug this apparatus during lightning storms or when 
unused for long periods of time
14. Refer all servicing to qualifi ed service personnel. 
Servicing is required when the apparatus has been 
damaged in any way, such as when the power-supply 
cord or plug is damaged, liquid has been spilled or 
objects have fallen into the apparatus, the apparatus 
has been exposed to rain or moisture, does not operate 
normally, or has been dropped
Additional Safety Information
15.  Th  is product may contain lead. Disposal of these 
materials may be regulated due to environmental 
considerations.
  For disposal or recycling information, please contact 
your local authorities or the Electronic Industries 
Alliance: www.eiae org.16. Damage Requiring Service -Th  e appliance should be 
serviced by qualifi ed service personnel when:
A. Th  e power supply cord or the plug has been damaged;
or
B. Objects have fallen, or liquid has been spilled into
the appliance; 
or
C. Th  e appliance has been exposed to rain; 
or
D. Th  e appliance does not appear to operate normally or 
exhibits a marked change in performance; 
or
E. Th  e appliance has been dropped, or the enclosure 
damaged.
17.  Tilt/Stability - All monitors must comply with 
recommended international global safety standards for 
tilt and stability properties of its cabinet design. 
Do not compromise these design standards by applying 
excessive pull force to the front, or top, of the cabinet 
which could ultimately overturn the product.
  Also, do not endanger yourself, or children, by placing 
electronic equipment/toys on the top of the cabinet.
Such items could unsuspectingly fall from the top of the 
set and cause product damage and/or personal injury.
18. Wall/Ceiling Mounting - Th  e appliance should be 
mounted to a wall/ceiling only as recommended by the 
manufacturer.
19. Power Lines - An outdoor antenna should be located 
away from power lines.
20. Outdoor Antenna Grounding - If an outside antenna is 
connected to the receiver, be sure the antenna system 
is grounded so as to provide some protection against 
voltage surges and built up static charges.
  Section 810 of the National Electric code. ANSI/NFPA
  No.70-1984, provides information with respect to 
proper grounding of the mats and supporting structure, 
grounding of the lead-in wire to an antenna-discharge 
unit, size of grounding connectors, location of antenna 
discharge unit, connection to grounding electrodes and 
requirements for the grounding electrode.
21. Objects and Liquid Entry - Care should be taken so that 
objects do not fall and liquids are not spilled into the 
enclosure through openings.
  Apparatus shall not be exposed to dripping or splashing 
and no objects fi  lled with liquids, such as vases, shall be 
placed on apparatusWA R N I N G
To  r e d u c e  t h e  r i s k  o f  fi  re or electric shock, do not expose 
this apparatus to rain or moisture.
Important Safety Instructions
 
						

							English-2
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS 
UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS 
CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING 
TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION:  TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL 
SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD 
FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. 
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
 Th  is symbol warns user that uninsulated voltage within the unit may have suffi    cient magnitude to cause electric shock. 
Th  erefore, it is dangerous to make any kind of contact with any part inside this unit.
 Th  is symbol alerts the user that important literature concerning the operation and maintenance of this unit has been 
included. Th  erefore, it should be read carefully in order to avoid any problems.
Impor tant Information
Canadian Department of
Communications Compliance Statement
DOC: Th  is Class B digital apparatus meets all requirements of the Canadian 
Interference-Causing Equipment Regulations.
FCC Information
1.  Use the attached specifi ed cables with the P426Y3(P42XC10), 
P506Y4(P50XC10) or P606Y5(P60XC10) color monitor so as not to 
interfere with radio and television reception.
  (1)  Please use the supplied power cord or equivalent to 
  ensure FCC compliance.
 (2) Please use shielded video signal cable,
  15-pin mini D-SUB to 15-pin mini D-SUB 
  with ferrite cores on both ends (not included).
2. Th  is equipment has been tested and found to comply with the limits 
for a Class B digital device, pursuant to part 15 of the FCC Rules. Th ese 
limits are designed to provide reasonable protection against harmful 
interference in a residential installation. Th  is equipment generates, uses, 
and can radiate radio frequency energy, and, if not installed and used 
in accordance with the instructions, may cause harmful interference to 
radio communications. However, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be 
determined by turning the equipment off   and on, the user is encouraged 
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
diff  erent from that to which the receiver is connected.
Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/
television technician for additional suggestions. Th  e user may fi nd the 
following booklet, prepared by the Federal Communications Commission, 
helpful: “How to Identify and Resolve Radio-TV Interference Problems.” Th is 
booklet is available from the U.S. Government Printing Offi  ce, Washington, 
D.C., 20402, Stock No. 004-000-00345-4.
WA R N I N G
Th  is product equipped with a three-wire grounding (earthed) plug - a plug 
that has a third (grounding) pin. Th is plug only fi ts a grounding-type power 
outlet. If you are unable to insert the plug into an outlet, contact a licensed 
electrician to replace the outlet with a properly grounded one. Do not defeat 
the safety purpose of the grounding plug.•
•
•
•
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not 
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the AC 
voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.
Plug Type North AmericaEuropean
ContinentalU.K. Chinese Japanese
Plug Shape
Country
VoltageU.S.A./Canada U.K. China JapanEU (except U.K.)
120* 230 220 100230
*When operating the PlasmaSync monitor with its AC 125-240V power supply, use a power supply cord that matches the power 
supply voltage of the AC power outlet being used.
 
						

							English
English-3
Safety Precautions
and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE 
THE FOLLOWING WHEN SETTING UP AND 
USING THE MONITOR:
Th  e plasma display's panel is made up of fi ne picture 
elements (cells), of which more than 99.99 percent are active 
cells. Some cells may not produce light or remain constantly 
lit. For safe operation and to avoid damaging the unit, read 
carefully and observe the following instructions. 
DO NOT OPEN THE MONITOR. Th  ere are no user-
serviceable parts inside and opening or removing covers 
may expose you to dangerous shock hazards or other 
risks. Th  e manufacturer is not liable for any bodily harm 
or damage caused if unqualifi ed persons attempt service 
or open the back cover. Refer all servicing to qualifi ed 
service personnel.
Do not spill any liquids into the cabinet or use your 
monitor near water.
Do not insert objects of any kind into the cabinet slots, 
as they may touch dangerous voltage points, which can 
be harmful or fatal or may cause electric shock, fi re or 
equipment failure.
Do not bend, crimp or otherwise damage the power cord. 
Do not place any heav y objects on the power cord. 
Damage to the cord may cause shock or fi re.
Do not place this product on a sloping or unstable cart, 
stand or table, as the monitor may fall, causing serious 
damage to the monitor.
Do not use in a moving vehicle, as the unit could drop or 
topple over and cause injuries.
Th  e power cable connector is the primary means of 
detaching the system from the power supply. Th e 
monitor should be installed close to a power outlet that 
is easily accessible. 
Th  is equipment shall be connected to a MAIN outlet 
with a protective earth-ground connection. Do not place 
any objects onto the monitor and do not use the monitor 
outdoors.
Do not use this unit’s polarized plug with an extension 
cord or with outlets unless the prongs can be inserted 
fully.
Th  e power supply cord you use must have been approved 
by and comply with the safety standards of your 
country. (Type H05VV-F 3G 1mm
2 should be used in 
Europe)
In UK, use a BS-approved power cord with molded plug 
having a black (13A) fuse installed for use with this 
monitor.
Use only with 100 V to 240 V 50 Hz/60 Hz AC power 
supply. Continued operation at line voltages greater than 
100 V to 240 V AC will shorten the life of the unit, and 
might even cause a fi re hazard. •
•
•
•
•
•
•
•
•
•
•
•Unplug the power cord during electrical storms or when 
the unit will not be in use for a long period.
Do not use monitor in high temperature, humid, dusty, 
or oily areas.
Do not cover vent on monitor.
Clean plasma ventilation areas using a vacuum cleaner 
with a soft    brush nozzle attachment.
To ensure proper ventilation, cleaning the ventilation 
areas must be carried out monthly. More frequent 
cleaning may be necessary depending on the 
environment in which the plasma monitor is installed.
Allow adequate ventilation around the monitor so that 
heat can properly dissipate. Do not block ventilated 
openings or place the monitor near a radiator or other 
heat sources. Do not put anything on top of monitor.
Handle with care when transporting. Save packaging for 
transporting.
As is the case with any phosphor-based display (like a 
CRT monitor, for example) light output will gradually 
decrease over the life of a Plasma Display Panel.
To avoid sulfurization it is strongly recommended not to 
place the unit in a dressing room in a public bath or hot 
spring bath.
           CAUTION
Immediately unplug your monitor from the wall outlet and 
refer servicing to qualifi ed service personnel under the 
following conditions:
When the power supply cord or plug is damaged.
If liquid has been spilled on, or objects have fallen into 
the monitor.
If the monitor has been exposed to rain or water.
If the monitor has been dropped or the cabinet 
damaged.
If the monitor does not operate normally by following 
operating instructions. •
•
•
•
•
•
•
•
•
•
•
•
•
•
Safety Precautions and Maintenance
 
						

							English-4
Recommended Use
CAUTION
CORRECT PLACEMENT AND ADJUSTMENT OF 
THE MONITOR CAN REDUCE EYE, SHOULDER AND 
NECK FATIGUE. CHECK THE FOLLOWING WHEN 
POSITIONING THE MONITOR:
For optimum performance, allow 20 minutes for warm-
up.
Rest your eyes periodically by focusing on an object at 
least 5 feet away. Blink oft en.
Position the monitor at a 90 degree angle to windows 
and other light sources to minimize glare and 
refl ections.
Clean the monitor surface with a lint-free, nonabrasive 
cloth. Avoid using any cleaning solution or glass 
cleaner.
Adjust the monitor’s brightness and contrast controls to 
enhance readability.
Get regular eye checkups.
Ergonomics
To realize the maximum ergonomic benefi ts, we recommend 
the following:
Use the preset Size and Position controls with standard 
signals.
Use the preset Color Setting.
Do not use primary color blue on a dark background, as 
it is diffi  cult to see and may produce eye fatigue due to 
insuffi  cient contrast.
Th  is equipment is not for use at video display work 
station according to Bildscharb V.
For more detailed information on setting up a healthy work 
environment, refer to the following document:
  American National Standard for Human Factors
Engineering of Visual Display Terminal Workstations
ANSI-HFS Standard No. 100-1988
Published by:
Th  e Human Factors and Ergonomics Society
P.O. Box 1369, Santa Monica, California 90406. •
•
•
•
•
•
•
•
•
•
Cleaning the Panel
When the panel becomes dusty or dirty, wipe gently 
with soft  cloth.
Do not rub the panel with coarse material.
Do not apply pressure to the surface.
Do not use OA cleaner. OA cleaner will cause 
deterioration or discolor the surface.
Cleaning the Cabinet
Unplug t he power supply.
Gently wipe the cabinet with a soft  cloth.
To clean the cabinet, dampen the cloth with a neutral 
detergent and water, wipe the cabinet and follow with a 
dry cloth.
NOTE: Th  e surface of the cabinet is composed of many 
types of plastic. 
DO NOT clean with benzene thinner, alkaline 
detergent, alcoholic system detergent, glass cleaner, 
wax, polish cleaner, soap powder, or insecticide. 
Rubber or vinyl should not be in contact with 
the cabinet for an extended period of time. Th ese 
types of fl uids and materials can cause the paint to 
deteriorate, crack or peel.
CLEANING THE VENT HOLES
Clean plasma ventilation areas using a vacuum cleaner 
with a soft    brush nozzle attachment.
To ensure proper ventilation, cleaning the ventilation 
areas must be carried out monthly. More frequent 
cleaning may be necessary depending on the 
environment in which the plasma monitor is installed. •
•
•
•
•
•
•
•
•
 
						

							English
English-5
Recommended Use - continued
To avoid or minimize image 
retention:
 
Like all phosphor-based display devices and all other gas 
plasma displays, plasma monitors can be susceptible to image 
retention under certain circumstances. Certain operating 
conditions, such as the continuous display of a static 
image over a prolonged period of time, can result in image 
retention if proper precautions are not taken. To protect 
your investment in this plasma monitor, please adhere to the 
following guidelines and recommendations for minimizing 
the occurrence of image retention:
Always enable and use your computer’s screen saver 
function during use with a computer input source.
Display a moving image whenever possible.
Change the position of the menu display from time to 
time.
Always power down the monitor when you are fi nished 
using it.
To reduce the likelihood of 
image retention from long-term 
use:
Lower the Brightness and Contrast levels as much as 
possible without impairing image readability.
Display an image with many colors and color gradations 
(i.e. photographic or photo-realistic images).
Create image content with minimal contrast between 
light and dark areas. Use complementary or pastel colors 
whenever possible.
Avoid displaying images with few colors and distinct, 
sharply defi ned borders between colors.
Plasma monitor driving sound
Th  e panel of the Plasma monitor is composed of 
extremely fi  ne pixels and these pixels emit light 
according to received video signals. Th  is principle may 
cause you to hear a buzz or electrical hum coming from 
the Plasma monitor. Also note that the rotation speed 
of the cooling fan motor increases when the ambient 
temperature of the Plasma monitor becomes high. You 
may hear the sound of the motor at that time.
NOTE: Th  e following items are not covered by the 
warranty.
• Image retention
• Panel generated sound. Examples: Fan motor   
   and electrical noises circuit humming /glass panel 
   buzzing. •
•
•
•
•
•
•
•
•
OPERATING ENVIRONMENT
Operating environment temperature and humidity: 0 °C to 
+40 °C (+32 °F to +104 °F); less than 80%RH (cooling vents 
not blocked) Do not install this unit in a poorly ventilated 
area, or in locations exposed to high humidity or direct 
sunlight (or strong artifi cial light)
WARNING
Not for use in a computer room as defi ned in the Standard 
for the Protection of Electronic Computer/Data Processing 
Equipment ANSI/NFPA 75.
NOTE:  Please use shielded video signal cable, 15-pin mini 
D-SUB to 15-pin mini D-SUB with ferrite cores on 
both ends (not included).
 
						

							English-6
Using Optional Stand/Mounts
An optional stand or mounting apparatus can be installed 
either while the unit is in the upright position or while the 
unit is face-down.
To install the stand while in the upright position, lower the 
monitor onto to the feet as shown (Figure 1). Use the handles 
to support the display while lowering the support holes 
underneath the display onto the feet.
If stand or mounting apparatus is to be installed while the 
unit is face-down (Figure 2), be sure to lay the protective 
sheet (the foam sheet that the unit was wrapped in) 
underneath the unit  on order to prevent damage to the 
screen. 
Th  is unit must be used with a stand or some type of 
mounting apparatus. Th  is unit is not designed for use 
without additional support.
For correct Installation and Mounting it is 
recommended to use a trained, authorized dealer.
Failure to follow correct mounting procedures could 
result in dame to the unit or to the installer.
Product warranty does not cover damage caused by 
improper installation.
CAUTION:
To install, follow those instructions included with the 
stand or mounting apparatus. Use only those devices 
recommended by the manufacturer.
Make sure to install stand or mounting apparatus to the 
unit while on a surface that is strong and stable enough 
to support the weight of the unit, such as a fl oor or 
sturdy table.
Use the specifi ed clasps for installation.
Take necessary steps to prevent the unit from tipping or 
falling.
Mounting Location
Th  e ceiling and wall must be strong enough to support the 
monitor and mounting accessories.
DO NOT install in locations where a door or gate can hit 
the unit.
DO NOT install in areas where the unit will be subjected 
to strong vibrations and dust.
DO NOT install near where the main power supply 
enters the building.
DO NOT install in where people can easily grab and 
hang onto the unit or the mounting apparatus.
When mounting in an enclosure or in a recessed area, as 
in a wall, leave at least 2 inches (50mm) of space between 
the monitor and the wall for proper ventilation (Figure 3). •
•
•
•
•
•
•
•
•
•
•
•Allow adequate ventilation or provide air conditioning 
around the monitor, so that heat can properly dissipate 
away from the unit and mounting apparatus. •
50mm (2)
50mm (2)
50mm (2)
50mm (2)
50mm (2)
Installation
Figure 3Figure 1
Figure 2
Ta b l eProtective Sheet
 
						

							English
English-7
Mounting on Ceiling
Ensure that the ceiling is sturdy enough to support the 
weight of the unit and the mounting apparatus over 
time, against earthquakes, unexpected vibrations, and 
other external forces.
Be sure the unit is mounted to a solid structure within 
the ceiling, such as a support beam. Secure the monitor 
using bolts, spring lock washers, washer and nut.
DO NOT mount to areas that have no supporting 
internal structure. DO NOT use wood screws or anchor 
screws for mounting. DO NOT mount the unit to trim 
or to hanging fi  xtures.
Maintenance
Periodically check for loose screws, gaps, distortions, 
or other problems that may occur with the mounting 
apparatus. If a problem is detected, please refer to 
qualifi ed personnel for service.
Regularly check the mounting location for signs of 
damage or weakness that may occur over time.
Please note the following when 
mounting on wall or ceiling.
When using mounting accessories other than those that 
are NEC approved, they must comply with the VESA-
compatible (FDMlv1) mounting method.
NEC strongly recommends 
using size M8 screws 
(16mm + thickness of 
bracket in length). If using 
screws longer than 16mm, 
check the depth of the 
hole.(Recommended Fasten 
Force: 1125 - 1375N•cm)
NEC recommends mounting 
interfaces that comply with 
UL1678 standard in North 
America.
Orientation
DO NOT use this monitor in the 
portrait position. Doing so may cause 
failure and void the warranty.•
•
•
•
•
•
•
Cable Management
To conveniently manage cables, use the cable clamps 
provided to bundle the power cord together with the signal 
and audio cables at the back of the display.
To attach cable clamps:
1.   Attach the cable clamps to the display. Insert the anchor 
of the clamp into the hole on the back of the display. 
Th  ere are 4 cable clamps and 4 clamp holes on the unit. 
2.   Aft  er the cable clamp is positioned on the display, wrap 
the end around the cables. Place the end of the clamp 
into the slot near the anchor. Pull until cables are snug.
  Clamps are designed to stay in place. Once in position, 
they will be diffi  cult to remove.
3.   Cables can be routed to the right or left   of the clamp. 
Use the beaded bands to secure the cables together along 
their length. Make sure the cables are fully supported.
To  d e t a c h  c l a m p s :
  Using pliers, twist the clamp 90 degrees and pull 
outward. It is possible that the clamp can weaken over 
time and removing it may cause damage to the clamp.
Installation - continued
Holes for Clamp 
anchors
Anchor
Slot
Closed Clamp
16mm
Screw length should equal 
depth of hole (16mm) + the 
thickness of mounting bracket. UnitMounting 
Bracket
Screw
Thickness 
of  Bracket